Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM C

1KR-FE ENGINE CONTROL  SFI SYSTEM  P035113  Ignition Coil "A" Circuit Open  P035213  Ignition Coil "B" Circuit Open  P035313  Ignition Coil "C" Circuit Open  


DESCRIPTION

A direct ignition system is used on this vehicle.

The direct ignition system is a 1-cylinder ignition system in which each cylinder is ignited by one No. 1 ignition coil and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The sparks of the spark plugs pass from the center electrode to the ground electrodes.

The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches on and off the current to the primary coil. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority
P035113 Ignition Coil "A" Circuit Open Open or short in No. 1 ignition coil signal circuit (3 trip detection logic).
·

Ignition system

·

Open or short in No. 1 ignition coil (No. 1 cylinder) circuit

·

No. 1 ignition coil (No. 1 cylinder)

·

ECM


Comes on DTC stored (except Euro-OBD)
- (Euro-OBD)
Engine A
P035213 Ignition Coil "B" Circuit Open Open or short in No. 1 ignition coil signal circuit (3 trip detection logic).
·

Ignition system

·

Open or short in No. 1 ignition coil (No. 2 cylinder) circuit

·

No. 1 ignition coil (No. 2 cylinder)

·

ECM


Comes on DTC stored (except Euro-OBD)
- (Euro-OBD)
Engine A
P035313 Ignition Coil "C" Circuit Open Open or short in No. 1 ignition coil signal circuit (3 trip detection logic).
·

Ignition system

·

Open or short in No. 1 ignition coil (No. 3 cylinder) circuit

·

No. 1 ignition coil (No. 3 cylinder)

·

ECM


Comes on DTC stored (except Euro-OBD)
- (Euro-OBD)
Engine A

WIRING DIAGRAM

A459181E01
2.385,0.292 2.615,0.49 0.229,0.198 10 false 24 2.906,0.271 3.156,0.469 0.25,0.198 10 false *1 1.969,0.385 2.375,0.563 0.406,0.177 10 false IGPD 0.802,0.698 1.135,0.865 0.333,0.167 10 false H45 1.083,0.708 2.667,1.125 1.583,0.417 10 false Certification ECU (Smart Key ECU Assembly)*1 1.083,1.615 1.24,1.813 0.156,0.198 10 false 7 2.365,1.635 2.521,1.833 0.156,0.198 10 false 8 1.302,1.615 1.708,1.792 0.406,0.177 10 false AM1 2.073,1.615 2.427,1.792 0.354,0.177 10 false IG1 0.271,5.104 0.521,5.302 0.25,0.198 10 false *2 2.885,1.531 3.135,1.729 0.25,0.198 10 false *2 0.781,2.104 1.115,2.271 0.333,0.167 10 false H54 0.698,2.26 3.115,2.458 2.417,0.198 10 false Ignition or Starter Switch Assembly*2 0.552,1.854 0.958,2.031 0.406,0.177 10 false AM1 1.948,4.26 2.354,4.438 0.406,0.177 10 false IGP 2.75,4.073 3.156,4.25 0.406,0.177 10 false INJ 0.802,4.875 1.99,5.104 1.188,0.229 10 false BATT-MAIN NO.1 0.917,4.083 1.677,4.281 0.76,0.198 10 false IGP-MAIN 0.99,5.75 1.563,5.938 0.573,0.188 10 false Battery 4.094,0.906 4.25,1.104 0.156,0.198 10 false 1 4.104,1.219 4.26,1.417 0.156,0.198 10 false 3 4.292,1.031 4.583,1.198 0.292,0.167 10 false +B 4.292,1.323 4.656,1.49 0.365,0.167 10 false GND 5.042,1.177 5.406,1.344 0.365,0.167 10 false IGT 5.354,1.042 5.51,1.24 0.156,0.198 10 false 2 5.573,1.052 5.865,1.219 0.292,0.167 10 false 27 5.802,1.052 6.188,1.219 0.385,0.167 10 false IGT1 4.125,1.615 4.479,1.813 0.354,0.198 10 false D1 4.323,1.625 5.49,1.99 1.167,0.365 10 false No. 1 Ignition Coil (No. 1 Cylinder) 4.104,2.573 4.26,2.771 0.156,0.198 10 false 1 4.104,2.875 4.26,3.073 0.156,0.198 10 false 3 4.292,2.677 4.583,2.844 0.292,0.167 10 false +B 4.292,2.99 4.656,3.156 0.365,0.167 10 false GND 4.958,2.813 5.323,2.979 0.365,0.167 10 false IGT2 5.344,2.719 5.5,2.917 0.156,0.198 10 false 2 5.573,2.719 5.865,2.885 0.292,0.167 10 false 57 5.802,2.708 6.188,2.875 0.385,0.167 10 false IGT2 5.354,4.323 5.51,4.521 0.156,0.198 10 false 2 5.573,4.333 5.865,4.5 0.292,0.167 10 false 56 5.802,4.333 6.188,4.5 0.385,0.167 10 false IGT3 4.104,4.188 4.26,4.385 0.156,0.198 10 false 1 4.104,4.49 4.26,4.688 0.156,0.198 10 false 3 4.292,4.292 4.583,4.458 0.292,0.167 10 false +B 4.281,4.604 4.646,4.771 0.365,0.167 10 false GND 4.969,4.427 5.333,4.594 0.365,0.167 10 false IGT3 4.073,3.26 4.427,3.458 0.354,0.198 10 false D2 4.271,3.281 5.406,3.656 1.135,0.375 10 false No. 1 Ignition Coil (No. 2 Cylinder) 4.094,4.896 4.448,5.094 0.354,0.198 11 false D3 4.323,4.906 5.448,5.292 1.125,0.385 10 false No. 1 Ignition Coil (No. 3 Cylinder) 6.156,5.052 6.51,5.25 0.354,0.198 10 false D50 6.458,5.052 6.875,5.323 0.417,0.271 10 false ECM 1.698,5.927 4.604,6.125 2.906,0.198 10 false *1: w/ Entry and Start System 1.688,6.354 4.594,6.552 2.906,0.198 10 false *2: w/o Entry and Start System 2.406,3.833 2.563,4.031 0.156,0.198 10 false 5 1.656,3.813 1.813,4.01 0.156,0.198 10 false 3 2.417,3.323 2.573,3.521 0.156,0.198 10 false 1 1.635,3.323 1.792,3.521 0.156,0.198 10 false 2 0.313,3.052 2.458,3.25 2.146,0.198 10 false INP STD NO.1-3

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, perform idle learning.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

These DTCs indicate malfunctions relating to the primary circuit.

·

If DTC P035113 is output, check the No. 1 ignition coil (No. 1 cylinder) circuit.

·

If DTC P035213 is output, check the No. 1 ignition coil (No. 2 cylinder) circuit.

·

If DTC P035313 is output, check the No. 1 ignition coil (No. 3 cylinder) circuit.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT



NEXT

2.PERFORM SIMULATION TEST (SHUFFLE ARRANGEMENT OF NO. 1 IGNITION COILS)
2.PERFORM SIMULATION TEST (SHUFFLE ARRANGEMENT OF NO. 1 IGNITION COILS)

Pre-procedure1

a.

Shuffle arrangement of the No. 1 ignition coils (among No. 1 to No. 3 cylinders).

NOTICE:

Do not change the location of the connectors.



b.

Perform a simulation test.


Procedure1

c.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
Same DTC output A
Different ignition coil DTC output B


Post-procedure1

d.

None.



A

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 IGNITION COIL)

B

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 IGNITION COIL)

Pre-procedure1

a.

Disconnect the No. 1 ignition coil connectors.


b.

Turn the ignition switch to ON.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D1-1 (+B) - D1-3 (GND) Ignition switch ON 11 to 14 V
D2-1 (+B) - D2-3 (GND) Ignition switch ON 11 to 14 V
D3-1 (+B) - D3-3 (GND) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

4.CHECK HARNESS AND CONNECTOR (ECM - NO. 1 IGNITION COIL)

NG

5.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (ECM - NO. 1 IGNITION COIL)

Pre-procedure1

a.

Disconnect the ECM connector.


b.

Disconnect the No. 1 ignition coil connectors.


Procedure1

c.

Measure the resistance according the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition Output DTC
D50-27 (IGT1) - D1-2 (IGT) Always Below 1 Ω P035113
D50-57 (IGT2) - D2-2 (IGT2) Always Below 1 Ω P035213
D50-56 (IGT3) - D3-2 (IGT3) Always Below 1 Ω P035313
D50-27 (IGT1) or D1-2 (IGT) - Body ground Always 10 kΩ or higher P035113
D50-57 (IGT2) or D2-2 (IGT2) - Body ground Always 10 kΩ or higher P035213
D50-56 (IGT3) or D3-2 (IGT3) - Body ground Always 10 kΩ or higher P035313


Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - BODY GROUND)

Pre-procedure1

a.

Disconnect the No. 1 ignition coil connectors.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition Output DTC
D1-3 (GND) - Body ground Always Below 1 Ω P035113
D2-3 (GND) - Body ground Always Below 1 Ω P035213
D3-3 (GND) - Body ground Always Below 1 Ω P035313


Result:
Proceed to
OK
NG


Post-procedure1

c.

None.



OK

6.CHECK HARNESS AND CONNECTOR (IGP RELAY - NO. 1 IGNITION COIL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (IGP RELAY - NO. 1 IGNITION COIL)

Pre-procedure1

a.

Remove the IGP relay from the No. 1 engine room relay block and junction block assembly.


b.

Disconnect the No. 1 ignition coil connectors.


Procedure1

c.

Measure the resistance according the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
5 (IGP relay) - D1-1 (+B) Always Below 1 Ω
5 (IGP relay) - D2-1 (+B) Always Below 1 Ω
5 (IGP relay) - D3-1 (+B) Always Below 1 Ω
5 (IGP relay) or D1-1 (+B) - Body ground Always 10 kΩ or higher
5 (IGP relay) or D2-1 (+B) - Body ground Always 10 kΩ or higher
5 (IGP relay) or D3-1 (+B) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)