Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM C

1KR-FE ENGINE CONTROL  SFI SYSTEM  P05042B  Brake Switch "A"/"B" Signal Cross Coupled  


DESCRIPTION

The stop light switch assembly is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If both signals, which indicate the brake pedal is being depressed or released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch assembly and stores the DTC.

HINT:

The normal conditions are as shown in the table below. The signals can be read using the GTS.

Signal Brake pedal released In transition Brake pedal depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).

·

On the GTS, both the Data List items Stop Light Switch and ST1 are ON when the brake pedal is depressed because the ST1 indication characteristic is opposite to the Stop Light Switch indication.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority
P05042B Brake Switch "A"/"B" Signal Cross Coupled

Conditions (a) and (b) continue for 3 seconds or more (1 trip detection logic):

(a) Ignition switch ON

(b) STP signal off when ST1 signal off



·

Open or short in stop light switch signal circuit

·

Stop light switch assembly

·

ECM


Comes on DTC stored Engine A

WIRING DIAGRAM

A459177E03
0.792,0.573 1.198,0.75 0.406,0.177 10 false STOP 0.635,3.333 1.833,3.552 1.198,0.219 10 false BATT-MAIN NO.1 3.146,3.323 3.781,3.521 0.635,0.198 10 false IGP-MAIN 0.781,3.615 2.646,3.958 1.865,0.344 10 false from Certification ECU (Smart Key ECU Assembly)*1 0.781,4.219 3.521,4.521 2.74,0.302 10 false from Ignition or Starter Switch Assembly*2 0.563,4.5 1.083,4.677 0.521,0.177 10 false Battery 3.573,0.302 3.854,0.469 0.281,0.167 10 false 7 3.573,0.792 3.854,0.958 0.281,0.167 10 false 6 3.563,1.26 3.844,1.427 0.281,0.167 10 false 2 3.76,0.438 3.938,0.615 0.177,0.177 10 false B 3.76,0.938 3.938,1.115 0.177,0.177 10 false B 3.75,1.375 4.104,1.552 0.354,0.177 10 false GND 4.635,0.417 4.813,0.594 0.177,0.177 10 false L 4.646,1.365 4.823,1.542 0.177,0.177 10 false L 5.698,0.323 5.885,0.469 0.188,0.146 10 false 57 5.625,1.271 5.875,1.448 0.25,0.177 10 false 24 4.854,0.313 5.135,0.479 0.281,0.167 10 false 3 4.833,1.25 5.115,1.417 0.281,0.167 10 false 5 3.417,1.698 3.875,1.875 0.458,0.177 10 false A63 3.406,1.865 5.656,2.073 2.25,0.208 10 false Stop Light Switch Assembly 5.948,0.323 6.271,0.479 0.323,0.156 10 false STP 5.938,1.281 6.302,1.438 0.365,0.156 10 false ST1- 3.427,2.771 4.365,2.938 0.938,0.167 10 false ECU-IGP NO.3 4.417,3.906 4.719,4.063 0.302,0.156 10 false IGP 6.25,4.396 6.563,4.573 0.313,0.177 10 false A55 6.25,4.583 6.76,4.927 0.51,0.344 10 false ECM 0.406,1.719 1.448,1.917 1.042,0.198 10 false INP STD NO.1-3 1.208,5.021 5.031,5.219 3.823,0.198 10 false *1: w/ Entry and Start System 1.219,5.375 5.198,5.573 3.979,0.198 10 false *2: w/o Entry and Start System 4.115,3.469 4.271,3.667 0.156,0.198 10 false 1 4.875,3.479 5.031,3.677 0.156,0.198 10 false 2 4.104,3.063 4.26,3.26 0.156,0.198 10 false 3 4.885,3.073 5.042,3.271 0.156,0.198 10 false 5

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, perform idle learning.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

STP signal conditions can be checked using the GTS.

(a)

Connect the GTS to the DLC3.

(b)

Turn the ignition switch to ON.

(c)

Turn the GTS on.

(d)

Enter the following menus: Powertrain / Engine / Data List / All Data / Stop Light SW.

(e)

Check the STP signal when the brake pedal is depressed and released.



Brake Pedal Operation Stop Light SW
Depressed ON
Released OFF


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)

Pre-procedure1

a.

Disconnect the stop light switch assembly connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A63-7 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG


Post-procedure1

c.

None.



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY)

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)

Pre-procedure1

a.

Disconnect the stop light switch assembly connector.


b.

Turn the ignition switch to ON.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A63-6 (B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)

NG

6.CHECK HARNESS AND CONNECTOR (IGP RELAY - STOP LIGHT SWITCH ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)

Pre-procedure1

a.

Disconnect the stop light switch assembly connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A63-2 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

c.

None.



OK

4.CHECK TERMINAL VOLTAGE (STP AND ST1- VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK TERMINAL VOLTAGE (STP AND ST1- VOLTAGE)

Pre-procedure1

a.
F102339C06
0.729,0.229 1.042,0.427 0.313,0.198 10 *a 2.583,0.219 2.896,0.417 0.313,0.198 10 *b
*a Brake Pedal Depressed
*b Brake Pedal Released


Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Operation Specified Condition
A55-24 (ST1-) - Body ground Depressed Below 1.5 V
A55-57 (STP) - Body ground Depressed 7.5 to 14 V
A55-24 (ST1-) - Body ground Released 7.5 to 14 V
A55-57 (STP) - Body ground Released Below 1.5 V



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)

Pre-procedure1

a.

Disconnect the stop light switch assembly connector.


b.

Disconnect the ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A63-5 (L) - A55-24 (ST1-) Always Below 1 Ω
A63-3 (L) - A55-57 (STP) Always Below 1 Ω
A63-5 (L) or A55-24 (ST1-) - Body ground and other terminals Always 10 kΩ or higher
A63-3 (L) or A55-57 (STP) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (IGP RELAY - STOP LIGHT SWITCH ASSEMBLY)

Pre-procedure1

a.

Disconnect the IGP relay from the No. 1 engine room relay block and junction block assembly.


b.

Disconnect the stop light switch assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (IGP relay) - A63-6 (B) Always Below 1 Ω
5 (IGP relay) or A63-6 (B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

7.CHECK HARNESS AND CONNECTOR (IGP RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (IGP RELAY - BODY GROUND)

Pre-procedure1

a.

Disconnect the IGP relay from the No. 1 engine room relay block and junction block assembly.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (IGP relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

c.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR