Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM C

1KR-FE ENGINE CONTROL  SFI SYSTEM  P211173  Throttle Actuator "A" Control System Actuator Stuck Closed  


DESCRIPTION

Refer to DTC P060E87.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>P060E87

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority
P211173 Throttle Actuator "A" Control System Actuator Stuck Closed The throttle does not open when current is applied to the throttle motor (1 trip detection logic).
·

Open or short circuit in throttle motor circuit

·

Throttle body with motor assembly


Comes on DTC stored Engine B

WIRING DIAGRAM

CONFIRMATION DRIVING PATTERN

DTC P21173 is detected when the ignition switch to ON.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the throttle body with motor assembly, perform electronic throttle learning and idle learning.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTC OUTPUT (IN ADDITION TO DTC P211173)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
Only P211173 is output A
P211173 and other DTCs are output B


HINT:

If any DTCs other than P211173 are output, troubleshoot those DTCs first.




A

2.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)

B

GO TO DTC CHART

2.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)

Pre-procedure1

a.

Remove the throttle body with motor assembly.

HINT:

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>THROTTLE BODY>REMOVAL



Procedure1

b.

Check for contamination between the throttle valve and housing. If necessary, clean the throttle body with motor assembly. Also, check that the throttle valve moves smoothly.

OK:

Throttle valve is not contaminated with foreign matter and moves smoothly.



Result:
Proceed to
OK
NG


Post-procedure1

c.

None.



OK

3.CHECK HARNESS AND CONNECTOR (THROTTLE BODY WITH MOTOR ASSEMBLY - ECM)

NG

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (THROTTLE BODY WITH MOTOR ASSEMBLY - ECM)

Pre-procedure1

a.

Disconnect the throttle body with motor assembly connector.


b.

Disconnect the ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D50-103 (M+) - D18-6 (M+) Always Below 1 Ω
D50-135 (M-) - D18-5 (M-) Always Below 1 Ω
D50-103 (M+) or D18-6 (M+) - Body ground Always 10 kΩ or higher
D50-135 (M-) or D18-5 (M-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

4.REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

NEXT

5.PERFORM IDLE LEARNING
5.PERFORM IDLE LEARNING

NEXT

6.CLEAR DTC
6.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P211173)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P211173)

Pre-procedure1

a.

Turn the ignition switch to ON.


Procedure1

b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
OK:

DTCs are not output.



Result:
Proceed to
NEXT


Post-procedure1

c.

None.



NEXT

END