Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM J

1KR-FE ENGINE CONTROL  SFI SYSTEM  Ignition Circuit  


DESCRIPTION

A direct ignition system is used on this vehicle. The direct ignition system is a 1 cylinder ignition system which ignites one cylinder with one No. 1 ignition coil. In the 1 cylinder ignition system, one spark plug is connected to the end of the secondary winding. High voltage is generated in the secondary winding and is applied directly to the spark plug. The spark of the spark plug passes from the center electrode to the ground electrode.

The ECM determines the ignition timing and transmits the ignition signals for each cylinder. Using the ignition signal, the ECM turns on and off the power transistor inside the igniter, which switches on and off a current to the primary coil. When the current to the primary coil is cut off, high voltage is generated in the secondary coil and this voltage is applied to the spark plugs to create sparks inside the cylinders.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, perform idle learning.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


HINT:
·

Perform a spark test first. If none of the cylinders spark, or if only some cylinders do not spark, check this circuit to determine if the ignition coil and spark plug are normal.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 IGNITION COIL)
a.

Disconnect the No. 1 ignition coil connectors.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D1-1 (+B) - D1-3 (GND) Ignition switch ON 11 to 14 V
D2-1 (+B) - D2-3 (GND) Ignition switch ON 11 to 14 V
D3-1 (+B) - D3-3 (GND) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ECM - NO. 1 IGNITION COIL)

NG

3.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (ECM - NO. 1 IGNITION COIL)
a.

Disconnect the ECM connector.


b.

Disconnect the No. 1 ignition coil connectors.


c.

Measure the resistance according the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
D50-27 (IGT1) - D1-2 (IGT) Always Below 1 Ω
D50-57 (IGT2) - D2-2 (IGT2) Always Below 1 Ω
D50-56 (IGT3) - D3-2 (IGT3) Always Below 1 Ω
D50-27 (IGT1) or D1-2 (IGT) - Body ground Always 10 kΩ or higher
D50-57 (IGT2) or D2-2 (IGT2) - Body ground Always 10 kΩ or higher
D50-56 (IGT3) or D3-2 (IGT3) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - BODY GROUND)
a.

Disconnect the No. 1 ignition coil connectors.


b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
D1-3 (GND) - Body ground Always Below 1 Ω
D2-3 (GND) - Body ground Always Below 1 Ω
D3-3 (GND) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (IGP RELAY - NO. 1 IGNITION COIL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (IGP RELAY - NO. 1 IGNITION COIL)
a.

Remove the IGP relay from the No. 1 engine room relay block and junction block assembly.


b.

Disconnect the No. 1 ignition coil connectors.


c.

Measure the resistance according the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
5 (IGP relay) - D1-1 (+B) Always Below 1 Ω
5 (IGP relay) - D2-1 (+B) Always Below 1 Ω
5 (IGP relay) - D3-1 (+B) Always Below 1 Ω
5 (IGP relay) or D1-1 (+B) - Body ground Always 10 kΩ or higher
5 (IGP relay) or D2-1 (+B) - Body ground Always 10 kΩ or higher
5 (IGP relay) or D3-1 (+B) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)