Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM C

1KR-FE ENGINE CONTROL  SFI SYSTEM  P012011  Throttle / Pedal Position Sensor / Switch "A" Circuit Short to Ground  P012015  Throttle / Pedal Position Sensor / Switch "A" Circuit Short to Battery or Open  P022011  Throttle/Pedal Position Sensor/Switch "B" Circuit Short to Ground  P022015  Throttle/Pedal Position Sensor/Switch "B" Circuit Short to Battery or Open  


DESCRIPTION

Refer to DTC P01201C.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>P01201C

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority
P012011 Throttle / Pedal Position Sensor / Switch "A" Circuit Short to Ground Output voltage of VTA1 0.2 V or less for 0.14 seconds or more (1 trip detection logic).
·

Throttle position sensor (throttle body with motor assembly)

·

Open or short in VTA1 circuit

·

Open in VC circuit

·

ECM


Comes on DTC stored Engine A
P012015 Throttle / Pedal Position Sensor / Switch "A" Circuit Short to Battery or Open Output voltage of VTA1 4.8 V or more for 0.14 seconds or more (1 trip detection logic).
·

Throttle position sensor (throttle body with motor assembly)

·

Open in VTA1 circuit

·

Open in ETA circuit

·

Short between VC and VTA1 circuits

·

ECM


Comes on DTC stored Engine A
P022011 Throttle/Pedal Position Sensor/Switch "B" Circuit Short to Ground Output voltage of VTA2 0.2 V or less for 0.14 seconds or more (1 trip detection logic).
·

Throttle position sensor (throttle body with motor assembly)

·

Open or short in VTA2 circuit

·

Open in VC circuit

·

ECM


Comes on DTC stored Engine A
P022015 Throttle/Pedal Position Sensor/Switch "B" Circuit Short to Battery or Open Output voltage of VTA2 4.8 V or more for 0.14 seconds or more (1 trip detection logic).
·

Throttle position sensor (throttle body with motor assembly)

·

Open in VTA2 circuit

·

Open in ETA circuit

·

Short between VC and VTA2 circuits

·

ECM


Comes on DTC stored Engine A

WIRING DIAGRAM

CONFIRMATION DRIVING PATTERN

These DTCs are detected when the ignition switch is ON or the engine is running.

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM and/or throttle body with motor assembly, perform electronic throttle learning and idle learning.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION

·

If any DTCs related to the crankshaft position sensor, throttle position sensor and accelerator pedal sensor assembly are output simultaneously, inspect the VC circuit of each component.



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (THROTTLE POSITION SENSOR VOLTAGE)
a.

Read the values displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Throttle Position Sensor No.1 Voltage
Throttle Position Sensor No.2 Voltage
50003 372 75,76
Result:
When Accelerator Pedal Fully Released When Accelerator Pedal Fully Depressed Trouble Area Proceed to
Throttle Position Sensor No.1 Voltage Throttle Position Sensor No.2 Voltage Throttle Position Sensor No.1 Voltage Throttle Position Sensor No.2 Voltage
4.8 to 4.98 V 0 to 0.2 V 4.8 to 4.98 V 0 to 0.2 V VC circuit open A
4.5 to 4.98 V 0 to 0.2 V 4.8 to 4.98 V 0 to 0.2 V ETA circuit open
0 to 0.2 V, or 4.8 to 4.98 V 3.9 to 4.4 V 0 to 0.2 V, or 4.8 to 4.98 V 3.9 to 4.3 V VTA1 circuit open or shorted to ground
0.6 to 1.1 V 0 to 0.2 V, or 4.8 to 4.98 V 0.7 to 1.1 V 0 to 0.2 V, or 4.8 to 4.98 V VTA2 circuit open or shorted to ground
0.6 to 1.1 V 3.9 to 4.4 V 4.2 to 4.54 V 0.46 to 0.76 V Throttle position sensor circuit normal B




A

2.CHECK HARNESS AND CONNECTOR (THROTTLE BODY WITH MOTOR ASSEMBLY - ECM)

B

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P012011, P012015, P022011 OR P022015)
2.CHECK HARNESS AND CONNECTOR (THROTTLE BODY WITH MOTOR ASSEMBLY - ECM)

Pre-procedure1

a.

Disconnect the throttle body with motor assembly connector.


b.

Disconnect the ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D18-2 (VC) - D50-116 (VC) Always Below 1 Ω
D18-1 (VTA) - D50-117 (VTA1) Always Below 1 Ω
D18-3 (VTA2) - D50-83 (VTA2) Always Below 1 Ω
D18-4 (E2) - D50-115 (ETA) Always Below 1 Ω
D18-2 (VC) or D50-116 (VC) - Body ground Always 10 kΩ or higher
D18-1 (VTA) or D50-117 (VTA1) - Body ground Always 10 kΩ or higher
D18-3 (VTA2) or D50-83 (VTA2) - Body ground Always 10 kΩ or higher
D18-4 (E2) or D50-115 (ETA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF THROTTLE BODY WITH MOTOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF THROTTLE BODY WITH MOTOR ASSEMBLY)

Pre-procedure1

a.

Disconnect the throttle body with motor assembly connector.


b.

Turn the ignition switch to ON.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D18-2 (VC) - D18-4 (E2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

4.REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

NG

4.REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

NEXT

5.PERFORM IDLE LEARNING
5.PERFORM IDLE LEARNING

NEXT

6.CLEAR DTC
6.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P012011, P012015, P022011 OR P022015)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P012011, P012015, P022011 OR P022015)

Pre-procedure1

a.

Start the engine.


Procedure1

b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
OK:

DTCs are not output



Result:
Proceed to
OK
NG


Post-procedure1

c.

None.



OK

END

NG