Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM C

1KR-FE ENGINE CONTROL  SFI SYSTEM  P24521C  Particulate Filter Pressure Sensor "A" Circuit Voltage Out of Range  


DESCRIPTION

Refer to DTC P244B00.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>P244B00

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority
P24521C Particulate Filter Pressure Sensor "A" Circuit Voltage Out of Range Differential pressure sensor value at intake air flow of 50 kg/h or higher is -4.4 kPa a for 5 seconds or more (1 trip detection logic).
·

Incorrect vacuum transmitting hose assembly

·

Differential pressure sensor


- DTC stored (Euro-OBD)
- (except Euro-OBD)
Engine B

MONITOR DESCRIPTION

When the differential pressure sensor output is output with the positive and negative values reversed, incorrect connection of the differential pressure sensor and vacuum transmitting hose assembly is judged and the ECM stores a DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


1.

When the ambient temperature is 10°C or higher and the vehicle is driven for 15 minutes or more at a speed of 50 km/h or more.

2.

Turn the ignition switch off and wait for at least 30 seconds.

3.

Check that no DTCs are output.


WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P24521C)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
Only P24521C is output A
DTC P24521C and other DTCs are output B


HINT:

If any DTCs other than P24521C are output, troubleshoot those DTCs first.




A

2.CHECK BLOCKAGE OF VACUUM TRANSMITTING HOSE ASSEMBLY AND VACUUM PIPE (DIFFERENTIAL PRESSURE SENSOR - VACUUM PIPE)

B

GO TO DTC CHART

2.CHECK BLOCKAGE OF VACUUM TRANSMITTING HOSE ASSEMBLY AND VACUUM PIPE (DIFFERENTIAL PRESSURE SENSOR - VACUUM PIPE)
A467273C01
1.479,1.5 2.49,0.552 2.49,0.552 2.677,0.552 true 1.365,2.063 1.615,3.146 1.615,3.146 1.823,3.146 true 4.031,2.729 4.729,1.01 4.729,1.01 5.01,1.01 true 4.021,3.24 2.917,4 2.917,4 2.635,4 true 4.656,4.5 3.719,5.302 3.719,5.302 3.5,5.302 true 2.729,0.479 3.042,0.677 0.313,0.198 10 false *1 1.875,3.063 2.188,3.26 0.313,0.198 10 false *2 5.063,0.917 5.375,1.115 0.313,0.198 10 false *1 2.458,3.927 2.771,4.125 0.313,0.198 10 false *2 3.333,5.219 3.646,5.417 0.313,0.198 10 false *3
*1 Differential Pressure Sensor *2 Vacuum Transmitting Hose Assembly
*3 No. 1 Vacuum Pipe - -


a.

Check if vacuum transmitting hose assembly between the differential pressure sensor and the vacuum pipe is correct.


b.

Check that there is no exhaust gas leak between the differential pressure sensor and the vacuum pipe.


Result:
Proceed to
OK
NG



OK

3.INSPECT DIFFERENTIAL PRESSURE SENSOR

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS

3.INSPECT DIFFERENTIAL PRESSURE SENSOR

OK

4.CLEAR DTC

NG

6.REPLACE DIFFERENTIAL PRESSURE SENSOR
4.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P24521C)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P24521C)

Pre-procedure1

a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Procedure1

b.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
OK:

DTCs are not output



Result:
Proceed to
NEXT


Post-procedure1

c.

None.



NEXT

END

6.REPLACE DIFFERENTIAL PRESSURE SENSOR

Pre-procedure1

a.

None.


Procedure1

b.

Replace the differential pressure sensor.

HINT:

Click hereEngine / Hybrid System>1KR-FE (EMISSION CONTROL)>DIFFERENTIAL PRESSURE SENSOR>REMOVAL



Result:
Proceed to
NEXT


Post-procedure1

c.

Start the engine and allow it to idle until the engine coolant temperature reaches 75°C (167°F) or higher (A).


d.

Turn the ignition switch off and wait for 30 seconds or more (B).


e.

Repeat the above procedures (A) and (B) 3 times.

HINT:

Procedures (A) and (B) must be repeated 3 times to complete the differential pressure sensor learning process.




NEXT

END