Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM C

1KR-FE ENGINE CONTROL  SFI SYSTEM  P24522A  Particulate Filter Pressure Sensor "A" Signal Stuck In Range  


DESCRIPTION

Refer to DTC P244B00.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>P244B00

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority
P24522A Particulate Filter Pressure Sensor "A" Signal Stuck In Range When ignition switch on, the differential pressure sensor output learning value at atmospheric pressure is above or below the specified value for 1 second or more (1 trip detection logic).
·

Open or short in differential pressure sensor circuit

·

Differential pressure sensor

·

Vacuum transmitting hose assembly

·

No. 1 vacuum pipe


- DTC stored (Euro-OBD)
- (except Euro-OBD)
Engine B

MONITOR DESCRIPTION

The differential pressure sensor output learning value is updated when ignition switch off after completely engine warmed up drive cycle. The sensor output should show its neutral (zero) value at the condition. The sensor output stuck in range is judged when the learning value is below or above the specified value at ignition switch on after the learning value updated.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


When the ambient temperature is 10°C or higher and the vehicle is driven for 15 minutes or more at a speed of 50 km/h or more, DTC P24522A is detected.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P24522A)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
Only P24522A is output A
P24522A and other DTCs are output B


HINT:

If any DTCs other than P24522A are output, troubleshoot those DTCs first.



A

2.CHECK FOR EXHAUST GAS LEAK

B

GO TO DTC CHART

2.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks in exhaust system.



Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTION OF VACUUM TRANSMITTING HOSE ASSEMBLY (DIFFERENTIAL PRESSURE SENSOR - VACUUM PIPE)

NG

REPAIR OR REPLACE EXHAUST SYSTEM

3.CHECK CONNECTION OF VACUUM TRANSMITTING HOSE ASSEMBLY (DIFFERENTIAL PRESSURE SENSOR - VACUUM PIPE)
A467274C01
2.698,2.521 1.823,1.302 1.823,1.302 1.563,1.302 true 1.313,3.719 1.531,3.719 1.531,3.719 2.698,2.979 true 3.344,4.094 3.854,4.917 3.854,4.917 4.042,4.917 true 1.385,1.219 1.698,1.417 0.313,0.198 10 false *1 1.135,3.625 1.448,3.823 0.313,0.198 10 false *2 4.104,4.833 4.417,5.031 0.313,0.198 10 false *3
*1 Differential Pressure Sensor *2 Vacuum Transmitting Hose Assembly
*3 No. 1 Vacuum Pipe - -


a.

Check the vacuum transmitting hose assembly is no exhaust gas leak between the differential pressure sensor and the vacuum pipe.

OK:

The vacuum transmitting hose assembly is no exhaust gas leak.



Result:
Proceed to
OK
NG



OK

4.CHECK BLOCKAGE OF VACUUM TRANSMITTING HOSE ASSEMBLY AND VACUUM PIPE

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS

4.CHECK BLOCKAGE OF VACUUM TRANSMITTING HOSE ASSEMBLY AND VACUUM PIPE
CAUTION:

Be careful of being burned by exhaust gases during the following inspection.


A467275C01
1.521,0.958 1.292,0.729 1.292,0.729 1.167,0.729 true 2.344,1.563 2.198,1.563 2.198,1.563 1.76,1.354 true 0.958,0.615 1.156,0.823 0.198,0.208 10 true *1 2.396,1.448 2.604,1.646 0.208,0.198 10 true *2
*1 Differential Pressure Sensor
*2 Vacuum Transmitting Hose Assembly


a.

Disconnect vacuum transmitting hose assembly on the differential pressure sensor.


b.

Start the engine.


c.

Check if there are exhaust gas pulsations from vacuum transmitting hose assembly during idling.


Result:
Proceed to
OK
NG



OK

5.INSPECT DIFFERENTIAL PRESSURE SENSOR

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS

5.INSPECT DIFFERENTIAL PRESSURE SENSOR

OK

6.CLEAR DTC

NG

8.CHECK HARNESS AND CONNECTOR (DIFFERENTIAL PRESSURE SENSOR - ECM)
6.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P24522A)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P24522A)

Pre-procedure1

a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Procedure1

b.

Read the Pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
OK:

DTCs are not output



Result:
Proceed to
NEXT


Post-procedure1

c.

None.



NEXT

END

8.CHECK HARNESS AND CONNECTOR (DIFFERENTIAL PRESSURE SENSOR - ECM)

Pre-procedure1

a.

Disconnect the differential pressure sensor connector.


b.

Disconnect the ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D72-3 (VC) - A55-35 (VCPX) Always Below 1 Ω
D72-2 (PEX) - A55-34 (PEX) Always Below 1 Ω
D72-1 (E2) - A55-32 (EPEX) Always Below 1 Ω
D72-3 (VC) or A55-35 (VCPX) - Body ground and other terminals Always 10 kΩ or higher
D72-2 (PEX) or A55-34 (PEX) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

9.REPLACE DIFFERENTIAL PRESSURE SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.REPLACE DIFFERENTIAL PRESSURE SENSOR

Pre-procedure1

a.

None.


Procedure1

b.

Replace the differential pressure sensor.

HINT:

Click hereEngine / Hybrid System>1KR-FE (EMISSION CONTROL)>DIFFERENTIAL PRESSURE SENSOR>REMOVAL



Result:
Proceed to
NEXT


Post-procedure1

c.

Start the engine and allow it to idle until the engine coolant temperature reaches 75°C (167°F) or higher (A).


d.

Turn the ignition switch off and wait for 30 seconds or more (B).


e.

Repeat the above procedures (A) and (B) 3 times.

HINT:

Procedures (A) and (B) must be repeated 3 times to complete the differential pressure sensor learning process.




NEXT

END