Home › Brake › PARKING BRAKE › FORCED RELEASE (w/ Electric Parking Brake) › from 2020.07
RM36W0E _54 Brake _089430 PARKING BRAKE _0432117 FORCED RELEASE(w/ Electric Parking Brake) A

PARKING BRAKE  FORCED RELEASE(w/ Electric Parking Brake)  OPERATION METHOD  


PROCEDURE

Hide 76973F 2.REMOVE REAR UNDER SIDE COVER RH

Hide 67914B 3.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 67913B 4.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 62112 5.REMOVE COWL SIDE TRIM BOARD LH

Hide 62111C 6.REMOVE COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure as for the LH side.


Hide 7. PARKING BRAKE FORCED RELEASE

CAUTION:

Work on a level surface to ensure safety.


NOTICE:
·

To release the parking brake, follow the procedure for when using SST.

·

If the parking brake cannot be released, follow the procedure for when not using SST.

·

When moving the vehicle after releasing the parking brake, install all parts and do not connect the 2 connectors shown in the illustration.

C437996

·

If the power switch is on (IG) or the engine is started with the 2 connectors disconnected, a DTC may be stored. Clear any DTCs after performing work.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>DTC CHECK / CLEAR



a.

When using SST:

i.

Park the vehicle on a level surface and move the shift lever to P.


ii.

Turn the power switch off and chock the wheels.


iii.

Disconnect the 2 connectors shown in the illustration.

C437996


iv.

Connect SST (09756-48020) to SST (09756-48070).

SST
09756-48020  09756-48070  

C437997C01
1.323,3.333 1.49,3.333 1.49,3.333 2.729,3.865 true 4.083,3.844 4.917,5.083 4.917,5.083 5.083,5.083 true 2.021,5.719 2.188,5.719 2.188,5.719 2.802,4.615 true 0.667,1.292 0.979,1.292 true 1.552,1.104 1.865,1.104 true 0.833,7.177 1.115,7.333 true 4.615,7.323 4.927,7.219 true 3.177,4.292 4.135,5.208 4.135,5.208 4.302,5.208 true 2.552,5.74 2.719,5.74 2.719,5.74 3.333,4.635 true 5.135,5 5.448,5.156 0.313,0.156 10 false *b 0.271,0.281 0.583,0.438 0.313,0.156 10 false *c 0.594,7.063 0.813,7.25 0.219,0.188 10 true *d 1.906,1.021 2.219,1.177 0.313,0.156 10 false *e 0.521,1.219 0.833,1.375 0.313,0.156 10 false *f 1.833,5.625 2.146,5.781 0.313,0.156 10 false *a 1.01,3.26 1.469,3.458 0.458,0.198 10 false SST 4.969,7.115 5.188,7.302 0.219,0.188 10 true *d 4.365,5.125 4.677,5.281 0.313,0.156 10 false *c 2.375,5.667 2.594,5.854 0.219,0.188 10 false *d
*a Brake Pedal *b Auxiliary Battery
*c SST (09756-48020) *d SST (09756-48070)
*e Release Button *f Finished Light
V100135

Connector - -



v.

Connect SST (09756-48070) to the 2 connectors inside of the vehicle.


vi.

Connect SST (09756-48020) to the auxiliary battery from the outside of the vehicle.


vii.

Push the release button on SST (09756-48020) with the brake pedal depressed.

CAUTION:

The vehicle may suddenly move when the parking brake is released. Make sure to perform the release operation with the brake pedal depressed.


HINT:
·

Confirm that the parking brake is operating by listening for operation sounds.

·

If no operation sounds are heard, push the release button on SST (09756-48020) with the brake pedal depressed.

·

The parking brake may not release if the auxiliary battery voltage is too low. In this case, perform the release operation again using a fully charged or new auxiliary battery.




viii.

When the finished light of SST (09756-48020) illuminates, release the brake pedal.


ix.

Move the vehicle forward and rearward to check that the parking brake is released.

CAUTION:

Be careful when performing this operation. The vehicle may suddenly move.


NOTICE:
·

When moving the vehicle after releasing the parking brake, check that the 2 connectors are disconnected.

·

The brake warning light (yellow) will illuminate when the vehicle is moved after releasing the parking brake.





b.

When not using SST:

NOTICE:

Perform the following procedure only when the parking brake cannot be released using SST.


HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



i.

Park the vehicle on a level surface and check that the shift lever is in P.


ii.

Turn the power switch off and check that the wheels are chocked.


iii.

Check that the 2 connectors shown in the illustration have been disconnected.

C437996


iv.

Remove the rear wheel.

Click hereGeneral>MAINTENANCE>TIRE AND WHEEL>REMOVAL

CAUTION:

When using a jack to lift the vehicle, make sure to support the vehicle using safety stands. Do not work on the vehicle with it supported only by a jack.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS



v.

Disconnect the No. 2 parking brake wire assembly connector from the parking brake actuator assembly.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>REMOVAL


vi.

Remove the parking brake actuator assembly from the rear disc brake cylinder assembly.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>REMOVAL


vii.
C437998

Insert an L-shaped T45 "TORX" wrench into the rear disc brake cylinder assembly.


viii.

Turn the L-shaped T45 "TORX" wrench 2 full rotations clockwise to release the parking brake lock.

NOTICE:
·

When moving the vehicle after releasing the parking brake, install all parts and do not connect the 2 connectors shown in the illustration.

C437996

·

The brake warning light (yellow) will illuminate when the vehicle is moved after releasing the parking brake.





Hide 62112 8.INSTALL COWL SIDE TRIM BOARD LH

Hide 62111C 9.INSTALL COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure as for the LH side.


Hide 67914B 10.INSTALL FRONT DOOR SCUFF PLATE LH

Hide 67913B 11.INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 76973F 12.INSTALL REAR UNDER SIDE COVER RH