Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _090986 STOP AND START _0432127 STOP AND START SYSTEM C

STOP AND START  STOP AND START SYSTEM  P085012  Park/Neutral Switch Circuit Short to Battery  P085014  Park/Neutral Switch Circuit Short to Ground or Open  


DESCRIPTION

The engine stop and start ECU detects malfunctions by comparing the conditions of the shift position signal and NSW signal. If a malfunction is detected, the engine stop and start ECU blinks the stop and start cancel indicator, prohibits stop and start control and stores DTC P085012 or P085014.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory Note
P085012 Park/Neutral Switch Circuit Short to Battery Both of the following conditions are met for 15 seconds or more (2 trip detection logic):
·

Ignition switch ON.

·

NSW signal is off with the shift lever in P or N.


·

Wire harness or connector

·

Park/Neutral position switch assembly

·

TCM

·

Engine stop and start ECU


Blinks DTC stored SAE Code: P0852
P085014 Park/Neutral Switch Circuit Short to Ground or Open Both of the following conditions are met for 2 seconds or more (2 trip detection logic):
·

Ignition switch ON.

·

NSW signal is on with the shift lever not in P or N.


·

Wire harness or connector

·

Park/Neutral position switch assembly

·

TCM

·

Engine stop and start ECU


Blinks DTC stored SAE Code: P0851

WIRING DIAGRAM

w/ Entry and Start System


A456550E04
3.281,0.125 5.521,0.448 2.24,0.323 10 false from BKUP LP Fuse 0.438,1.26 2.677,1.583 2.24,0.323 10 false ECM 4.521,3.5 6.729,3.927 2.208,0.427 10 false to ST NO. 1 Relay 6.042,3.708 6.542,3.948 0.5,0.24 10 false A67 6.031,3.917 7.104,4.635 1.073,0.719 10 false Engine Stop and Start ECU 6.208,3.115 6.552,3.406 0.344,0.292 10 false STA 6.219,0.51 6.563,0.802 0.344,0.292 10 false CLL 5.948,2.979 6.292,3.271 0.344,0.292 10 false 21 5.948,0.427 6.292,0.719 0.344,0.292 10 false 17 0.552,0.521 1.042,0.813 0.49,0.292 10 false NSW 0.792,2.177 1.281,2.469 0.49,0.292 10 false P 0.781,2.771 1.271,3.063 0.49,0.292 10 false R 0.781,3.333 1.271,3.625 0.49,0.292 10 false N 0.792,3.938 1.281,4.229 0.49,0.292 10 false D 0.26,4.385 0.75,4.677 0.49,0.292 10 false D71 1.427,4.896 1.917,5.188 0.49,0.292 10 false H45 0.448,1.094 0.938,1.385 0.49,0.292 10 false A54 4.438,1.052 4.927,1.344 0.49,0.292 10 false D45 4.438,1.24 5.771,1.667 1.333,0.427 10 false Park/Neutral Position Switch Assembly 1.021,0.396 1.51,0.688 0.49,0.292 10 false 23 1,2.115 1.49,2.406 0.49,0.292 10 false 29 1.01,2.688 1.5,2.979 0.49,0.292 10 false 30 1,3.25 1.49,3.542 0.49,0.292 10 false 32 1.01,3.844 1.5,4.135 0.49,0.292 10 false 31 1.948,1.833 2.438,2.125 0.49,0.292 10 false PL 2.438,1.833 2.927,2.125 0.49,0.292 10 false RL 2.885,1.833 3.375,2.125 0.49,0.292 10 false NL 3.344,1.833 3.833,2.125 0.49,0.292 10 false DL 3.885,1.844 4.375,2.135 0.49,0.292 10 false L 2.656,0.979 3.146,1.271 0.49,0.292 10 false RB 3.885,0.99 4.375,1.281 0.49,0.292 10 false B 2.781,0.729 3.271,1.021 0.49,0.292 10 false 2 3.885,0.729 4.375,1.021 0.49,0.292 10 false 4 2.063,2.083 2.552,2.385 0.49,0.302 10 false 6 2.521,2.073 3.01,2.365 0.49,0.292 10 false 1 2.969,2.073 3.458,2.365 0.49,0.292 10 false 9 3.438,2.083 3.927,2.375 0.49,0.292 10 false 7 3.906,2.073 4.396,2.365 0.49,0.292 10 false 5 0.25,4.552 1.083,5.104 0.833,0.552 10 false TCM 1.427,5.083 4.469,5.396 3.042,0.313 10 false Certification ECU (Smart Key ECU Assembly) 3.313,4.521 3.656,4.813 0.344,0.292 10 false STA 3.719,4.396 4.208,4.688 0.49,0.292 10 false 3


w/o Entry and Start System


A456551E05
3.292,0.406 5.531,0.729 2.24,0.323 10 false from BKUP LP Fuse 0.427,1.76 2.667,2.083 2.24,0.323 10 false ECM 4.552,3.802 6.635,4.229 2.083,0.427 10 false to ST NO. 1 Relay 5.792,4.125 6.135,4.417 0.344,0.292 10 false A67 5.781,4.292 7.156,4.719 1.375,0.427 10 false Engine Stop and Start ECU 6.219,3.375 6.563,3.667 0.344,0.292 10 false STA 6.219,0.823 6.563,1.115 0.344,0.292 10 false CLL 5.948,3.24 6.292,3.531 0.344,0.292 10 false 21 5.948,0.698 6.292,0.99 0.344,0.292 10 false 17 0.563,0.802 1.052,1.094 0.49,0.292 10 false NSW 0.792,2.531 1.281,2.823 0.49,0.292 10 false P 0.781,3.125 1.271,3.417 0.49,0.292 10 false R 0.781,3.688 1.271,3.979 0.49,0.292 10 false N 0.781,4.292 1.271,4.583 0.49,0.292 10 false D 0.448,1.583 0.938,1.875 0.49,0.292 10 false A54 4.406,1.521 4.896,1.813 0.49,0.292 10 false D45 4.406,1.688 5.74,2.115 1.333,0.427 10 false Park/Neutral Position Switch Assembly 0.979,0.719 1.469,1.01 0.49,0.292 10 false 23 1,2.427 1.49,2.719 0.49,0.292 10 false 29 1,3 1.49,3.292 0.49,0.292 10 false 30 0.99,3.563 1.479,3.854 0.49,0.292 10 false 32 1.01,4.156 1.5,4.448 0.49,0.292 10 false 31 1.958,2.135 2.448,2.427 0.49,0.292 10 false PL 2.438,2.146 2.927,2.438 0.49,0.292 10 false RL 2.875,2.135 3.365,2.427 0.49,0.292 10 false NL 3.354,2.135 3.844,2.427 0.49,0.292 10 false DL 3.906,2.146 4.396,2.438 0.49,0.292 10 false L 2.698,1.271 3.188,1.563 0.49,0.292 10 false RB 3.885,1.271 4.375,1.563 0.49,0.292 10 false B 2.813,1.042 3.302,1.333 0.49,0.292 10 false 2 3.906,1.063 4.396,1.354 0.49,0.292 10 false 4 2.063,2.375 2.552,2.667 0.49,0.292 10 false 6 2.521,2.385 3.01,2.677 0.49,0.292 10 false 1 2.979,2.365 3.469,2.656 0.49,0.292 10 false 9 3.438,2.365 3.927,2.656 0.49,0.292 10 false 7 3.906,2.375 4.396,2.667 0.49,0.292 10 false 5 0.292,4.844 1.135,5.427 0.844,0.583 10 false TCM 0.292,4.667 0.781,4.958 0.49,0.292 10 false D71 2.344,0.042 5.323,0.594 2.979,0.552 10 false from Ignition or Starter Switch Assembly 3.531,4.802 4.021,5.094 0.49,0.292 10 false A 1.417,1.24 1.906,1.531 0.49,0.292 10 false A 0.99,1.125 1.479,1.417 0.49,0.292 10 false 30 0.615,1.24 0.958,1.531 0.344,0.292 10 false STA


CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU, perform learning of the external backup boost converter (eco run vehicle converter assembly).

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

When the ECM is replaced on a vehicle with a non-specified auxiliary battery, it is necessary to perform auxiliary battery type switching.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

When the engine stop and start ECU or oil pump with motor assembly is replaced, check the oil pump with motor assembly.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA

·

For wire harness and connector inspection procedures and precautions, refer toGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

·

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.READ VALUE USING GTS (SHIFT SW STATUS)
a.

Enter the following menus: Powertrain / Transmission / Data List / Shift SW Status (P, R, N, D Range).

Powertrain > Transmission > Data List
Tester Display
Shift SW Status (P Range)
Shift SW Status (R Range)
Shift SW Status (N Range)
Shift SW Status (D Range)
50003 373 15,14,13,28

b.

In accordance with the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition
Shift SW Status (P Range) Park/Neutral position switch assembly status OFF or ON OFF: Shift lever not in P
ON: Shift lever in P
Shift SW Status (R Range) Park/Neutral position switch assembly status OFF or ON OFF: Shift lever not in R
ON: Shift lever in R
Shift SW Status (N Range) Park/Neutral position switch assembly status OFF or ON OFF: Shift lever not in N
ON: Shift lever in N
Shift SW Status (D Range) Park/Neutral position switch assembly status OFF or ON OFF: Shift lever not in D or S
ON: Shift lever in D or S

Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (NEUTRAL POSITION SW)

NG

5.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
2.READ VALUE USING GTS (NEUTRAL POSITION SW)
a.

Enter the following menus: Powertrain / Transmission / Data List / Neutral Position SW.

Powertrain > Transmission > Data List
Tester Display
Neutral Position SW
50003 373 20

b.

In accordance with the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition
Neutral Position SW Park/Neutral position switch assembly status OFF or ON OFF: Shift lever not in P or N
ON: Shift lever in P or N

Result:
Proceed to
OK
NG



OK

NG

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly.

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>PARK / NEUTRAL POSITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the A67 engine stop and start ECU connector.


b.

Disconnect the D45 park/neutral position switch assembly connector.


c.

Disconnect the A54 ECM connector.


d.

Disconnect the H45 certification ECU (smart key ECU Assembly) connector.*1

*1: w/ Entry and Start System



e.

Remove the ST NO. 1 relay from the No. 1 engine room relay block.


f.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition
A67-21 (STA) - D45-5 (L) Always Below 1 Ω
A67-17 (CLL) - D45-4 (B) Always Below 1 Ω
A67-21 (STA) - Body ground and other terminals Always 10 kΩ or higher
D45-5 (L) - Body ground and other terminals Always 10 kΩ or higher
A67-17 (CLL) - Body ground and other terminals Always 10 kΩ or higher
D45-4 (B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

OK

6.CHECK HARNESS AND CONNECTOR (ECM AND TCM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (ECM AND TCM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the D71 TCM connector.


b.

Disconnect the A54 ECM connector.


c.

Disconnect the D45 park/neutral position switch assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D71-29 (P) - D45-6 (PL) Always Below 1 Ω
D71 30 (R) - D45-1 (RL) Always Below 1 Ω
D71-32 (N) - D45-9 (NL) Always Below 1 Ω
D71-31 (D) - D45-7 (DL) Always Below 1 Ω
A54-23 (NSW) - D45-4 (B) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR