Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › 2020.07–2020.09
RM36W0E _51 Engine / Hybrid System _090986 STOP AND START _0432127 STOP AND START SYSTEM J

STOP AND START  STOP AND START SYSTEM  Failure to Restart from IG-ON Engine Stall  


DESCRIPTION

for CVT:

This is the troubleshooting procedure for situations where the engine does not restart when attempting to restart it after a failed engine start occurred under stop and start system control.


for Manual Transaxle:
·

This is the troubleshooting procedure for situations where the engine does not restart when attempting to restart it after either a failed engine start occurred under stop and start system control, or a mis-operation during vehicle takeoff resulted in an engine stall.

·

For information on stop and start control, refer to the system description.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>SYSTEM DESCRIPTION


CAUTION / NOTICE / HINT

PRECAUTIONS WHEN THE ENGINE STOP AND START ECU AND THE STARTER ASSEMBLY ARE REPLACED


NOTICE:
·

When the engine stop and start ECU is replaced, it is necessary to read the number of starter operations before replacement and store this number in the new engine stop and start ECU after replacement, and to perform external backup boost converter (eco run vehicle converter assembly) existence learning. Moreover, initialization/learning of the air conditioning information and initialization/learning of the deceleration sensor zero point are also required.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

When the engine stop and start ECU or electromagnetic oil pump (oil pump assembly w/ solenoid) has been replaced, it is necessary to check the operation of the electromagnetic oil pump (oil pump assembly w/ solenoid).

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

When the starter assembly is replaced, the number of starter operations stored in the engine stop and start ECU must be reset.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

When the starter assembly is replaced, "ST NO. 1 relay" must be also replaced.

·

Inspect the fuses for circuits related to this system before performing the following procedure.




PRECAUTIONS FOR FOUR-WHEEL TOWING


Do not tow the vehicle with all 4 wheels on the ground.

NOTICE:
·

Towing the vehicle with all 4 wheels on the ground may have a detrimental effect on the stop and start system, and could lead to damage.



HINT:

If it is absolutely necessary to tow the vehicle with all 4 wheels on the ground, before towing first turn the ignition switch off. Then, turn the ignition switch to ON without starting the engine, and tow the vehicle.



PRECAUTIONS WHEN REPLACING ECM


NOTICE:

When the ECM is replaced on a vehicle with a non-specified battery, it is necessary to perform battery type switching.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION



PROCEDURE

1.CHECK VEHICLE CONTROL HISTORY (Failure to Restart from IG-ON Engine Stall)
a.

Enter the following menus: Powertrain / Stop and Start / Utility / Vehicle Control History (RoB).

Powertrain > Stop and Start > Utility
Tester Display
Vehicle Control History (RoB)
50005 392 55

b.

Check vehicle control history.

HINT:
·

Checking the freeze frame data allows the vehicle conditions at the time of detection to be confirmed.

·

As Vehicle Control History may be overwritten whenever the trigger conditions are met, make sure to save the Vehicle Control History data before performing any inspections.




Result:
Result Proceed to
Vehicle control history [X0874: Stop & Start Restart Failure (Engine Restart after Engine Stall)] is output A
Vehicle control history [X0874: Stop & Start Restart Failure (Engine Restart after Engine Stall)] is not output B



A

2.CHECK VEHICLE SPECIFICATION

B

2.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
for CVT A
for Manual Transaxle B



A

3.CUSTOMER PROBLEM ANALYSIS AND SYMPTOM CONFIRMATION

B

4.CHECK VEHICLE CONDITION (DRIVER OPERATION ITEMS)
3.CUSTOMER PROBLEM ANALYSIS AND SYMPTOM CONFIRMATION
a.

Consult with the customer to determine if they performed operations that could result in an AT engine stall.

HINT:

(ex.) Heavy load, frequent shifts, etc.



Result:
Result Proceed to
Driver operations that could cause engine stall were performed A
None of the above conditions are met B



A

ENGINE STALL DUE TO DRIVER OPERATION

B

5.CHECK VEHICLE CONTROL HISTORY (STOP&START RESTART FAILURE (ENGINE RESTART AFTER ENGINE STALL)
4.CHECK VEHICLE CONDITION (DRIVER OPERATION ITEMS)
a.

Enter the following menus: Powertrain / Stop and Start / Utility / Vehicle Control History (RoB).

Powertrain > Stop and Start > Utility
Tester Display
Vehicle Control History (RoB)
50005 392 55

b.

Select the vehicle control history item [X0874: Stop&Start Restart Failure (Engine Restart after Engine Stall)] to display the data from the time of control.


c.

Check the output data, and check whether operations were performed that could result in an MT engine stall.


Result:
Result Proceed to
When failure to restart from Stop and Start occurred, check whether the vehicle was put into "Shift Position" and "Clutch Lower Switch" was released (= incorrect operation). Or, for all recorded points, "Neutral Switch" is "OFF" (= driving range) A
None of the above conditions are met B



A

ENGINE STALL DUE TO DRIVER OPERATION

B

5.CHECK VEHICLE CONTROL HISTORY (STOP&START RESTART FAILURE (ENGINE RESTART AFTER ENGINE STALL)
5.CHECK VEHICLE CONTROL HISTORY (STOP&START RESTART FAILURE (ENGINE RESTART AFTER ENGINE STALL)
a.

Enter the following menus: Powertrain / Stop and Start / Utility / Vehicle Control History (RoB).

Powertrain > Stop and Start > Utility
Tester Display
Vehicle Control History (RoB)
50005 392 55

b.

Select the vehicle control history item [X0874: Stop&Start Restart Failure (Engine Restart after Engine Stall)] to display the data from the time of control.


c.

Check the output data.


Result:
Result Proceed to
All recorded sections "Starter"*1 = OFF, and all recorded sections "Engine Speed" = 0 rpm
HINT:

It is possible that the starter drive command is not being sent from the engine stop and start ECU.


A
"Starter"*1 = ON for any sections, and all recorded sections "Engine Speed" = 0 rpm
HINT:

It is possible that the drive command is being sent from the engine stop and start ECU but the starter itself is not moving.


B
"Engine Speed" > 0 rpm for any sections
HINT:

It is possible that cranking was achieved but the engine stopped.


C


*1: Starter Status in the case of other than tandem starter (for 1KR-FE), Starter Motor Status in the case of tandem starter (for M15A-FKS)



A

REPLACE ENGINE STOP AND START ECU

Click hereEngine / Hybrid System>STOP AND START>ENGINE STOP AND START ECU>REMOVAL

HINT:

It is possible that there is a malfunction of the starter drive circuit inside the stop and start ECU.



B

6.CHECK VEHICLE CONTROL HISTORY (CRANKING TIME)

C

10.CHECK VEHICLE CONTROL HISTORY (CRANKING TIME)
6.CHECK VEHICLE CONTROL HISTORY (CRANKING TIME)
a.

Enter the following menus: Powertrain / Stop and Start / Utility / Vehicle Control History (RoB).

Powertrain > Stop and Start > Utility
Tester Display
Vehicle Control History (RoB)
50005 392 55

b.

Check the vehicle control history item "Cranking Time".


Result:
Result Proceed to
"Cranking Time" is 1.5 seconds or more
HINT:

It is possible that there is an external malfunction outside of the stop and start ECU (drive circuit).


A
"Cranking Time" is less than 1.5 seconds
HINT:

It is possible that there is a malfunction in the stop and start ECU (drive circuit).


B



A

7.CHECK ENGINE STOP AND START ECU (+B VOLTAGE)

B

7.CHECK ENGINE STOP AND START ECU (+B VOLTAGE)
a.

Disconnect the A67 engine stop and start ECU connector.


b.

Turn the ignition switch to ON.


c.

Turn off any electrical loads.


d.

Measure the resistance according to the value(s) in the table below.

OK:

11 V or higher


Standard Voltage:
Tester Connection Condition Specified Condition
A67-1 (+B) - Body ground Ignition switch ON 11 V or higher



Result:
Proceed to
OK
NG



OK

8.CHECK VEHICLE CONTROL HISTORY (BATTERY VOLTAGE)

NG

9.INSPECT AUXILIARY BATTERY
8.CHECK VEHICLE CONTROL HISTORY (BATTERY VOLTAGE)
a.

Enter the following menus: Powertrain / Stop and Start / Utility / Vehicle Control History (RoB).

Powertrain > Stop and Start > Utility
Tester Display
Vehicle Control History (RoB)
50005 392 55

b.

Check the voltage of the auxiliary battery.

HINT:
·

Depending on RoB detection timing, the minimum voltage from the previous startup will be stored for the Minimum Voltage (Cranking) and the Minimum Voltage (Starter Solenoid Engagement). For the battery condition at the start of the current driving cycle, see Battery Voltage.

·

When the value is 20, the value is being calculated.




Result:
Result Proceed to
Auxiliary battery voltage is 8.92 V or more A
Auxiliary battery voltage is less than 8.92 V B



A

B

9.INSPECT AUXILIARY BATTERY
9.INSPECT AUXILIARY BATTERY
a.

Measure the voltage of the auxiliary battery.

Standard Voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE AUXILIARY BATTERY

10.CHECK VEHICLE CONTROL HISTORY (CRANKING TIME)
a.

Enter the following menus: Powertrain / Stop and Start / Utility / Vehicle Control History (RoB).

Powertrain > Stop and Start > Utility
Tester Display
Vehicle Control History (RoB)
50005 392 55

b.

Select a vehicle control history item to display the "Cranking Time" and "Starter OFF Permission History (ECM)" data from the time of control.


c.

Check the output data.


Result:
Result Proceed to
"Cranking Time" is less than 1.5 seconds "Starter OFF Permission History (ECM)" is ON
HINT:

It is possible that the ECM made a judgment of complete combustion and the ECM then stopped the starter.


A
"Starter OFF Permission History (ECM)" is OFF
HINT:

It is possible that the engine stop and start ECU made a judgment of complete combustion and the engine stop and start ECU then stopped the starter.


B
"Cranking Time" is 1.5 seconds or more.
HINT:

It is possible that the stop andstart ECU did not stop the starter.


C



A

SFI SYSTEM (Poor Startability)

for 1KR-FE: Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>Engine Difficult to Start

for M15A-FKS: Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>Engine Difficult to Start

HINT:

Check whether the speed value of the EFI ECU is not a higher value than the original NE.



B

11.READ VALUE USING GTS (Engine Speed)

C

15.CHECK DATA POINTS (Engine Speed)
11.READ VALUE USING GTS (Engine Speed)
a.

Enter the following menus: Powertrain / Stop and Start / Data List / Engine Speed.

Powertrain > Stop and Start > Data List
Tester Display
Engine Speed
50003 392 502

b.

Using the Data List, check the current engine speed value of the stop and start ECU.

OK:

Stop and Start ECU "Engine Speed" > "Engine Speed (ENG)" + 300 rpm



Result:
Proceed to
OK
NG



OK

12.CHECK DATA POINTS (Engine Speed)

NG

14.CHECK ENGINE STOP AND START ECU (STA SIGNAL)
12.CHECK DATA POINTS (Engine Speed)
a.

Check the RoB data points.

OK:

For each and all of the data points, "Engine Speed" > "Engine Speed (ECM)" + 300 rpm



Result:
Proceed to
OK
NG



OK

READ VALUE USING GTS (Engine Speed)

NG

13.CHECK ENGINE STOP AND START ECU (STA SIGNAL)
13.CHECK ENGINE STOP AND START ECU (STA SIGNAL)
A471297C06
3.292,0.49 3.729,0.76 0.438,0.271 4.031,2.188 3.74,1.208 true 3.125,2.094 3.417,1.333 true 2.979,2.146 3.438,2.458 0.458,0.313 10 false STA 3.865,2.24 4.521,2.427 0.656,0.188 10 false DGND 3.375,0.552 3.802,0.75 0.427,0.198 10 false A67 0.896,0.365 1.271,0.563 0.375,0.198 10 false *a
*a Component with harness connected
(Engine Stop and Start ECU)
- -


a.

Enter the following menus: Powertrain / Stop and Start / Active Test / Starter Motor Drive Magnet Switch(Hood Close)

Powertrain > Stop and Start > Active Test
Tester Display
Starter Motor Drive Magnet Switch(Hood Close)
50004 392 42019

b.

Measure the voltage according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Voltage:
Tandem Starter (for M15A-FKS)
Tester Connection Condition Specified Condition
A67-21 (STA) - A67-6 (DGND) Performing Active Test, while cranking. 6 to 14 V

Except Tandem Starter (for 1KR-FE)
Tester Connection Condition Specified Condition
A67-21 (STA) - A67-6 (DGND) Performing Active Test, while cranking. 6 to 14 V



c.
A435595E01
3.021,1.271 3.354,1.479 0.333,0.208 10 false GND

Using an oscilloscope, measure the waveform immediately after starting.

Item Content
Tester Connection A67-21 (STA) - A67-6 (DGND)
Tool Setting 10 V/DIV, 200 ms./DIV
Condition During cranking

OK:

Voltage and waveform both normal



Result:
Proceed to
OK
NG



OK

INSPECT ENGINE (Pre-ignition, SFI System, Poor Startability)

NG

14.CHECK ENGINE STOP AND START ECU (STA SIGNAL)
A471297C06
3.292,0.49 3.729,0.76 0.438,0.271 4.031,2.188 3.74,1.208 true 3.125,2.094 3.417,1.333 true 2.979,2.146 3.438,2.458 0.458,0.313 10 false STA 3.865,2.24 4.521,2.427 0.656,0.188 10 false DGND 3.375,0.552 3.802,0.75 0.427,0.198 10 false A67 0.896,0.365 1.271,0.563 0.375,0.198 10 false *a
*a Component with harness connected
(Engine Stop and Start ECU)
- -


a.

Enter the following menus: Powertrain / Stop and Start / Active Test / Starter Motor Drive Magnet Switch(Hood Close)

Powertrain > Stop and Start > Active Test
Tester Display
Starter Motor Drive Magnet Switch(Hood Close)
50004 392 42019

b.

Measure the voltage according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Voltage:
Tandem Starter (for M15A-FKS)
Tester Connection Condition Specified Condition
A67-21 (STA) - A67-6 (DGND) Performing Active Test, while cranking. 6 to 14 V

Except Tandem Starter (for 1KR-FE)
Tester Connection Condition Specified Condition
A67-21 (STA) - A67-6 (DGND) Performing Active Test, while cranking. 6 to 14 V



c.
A435595E01
3.021,1.271 3.354,1.479 0.333,0.208 10 false GND

Using an oscilloscope, measure the waveform immediately after starting.

Item Content
Tester Connection A67-21 (STA) - A67-6 (DGND)
Tool Setting 10 V/DIV, 200 ms./DIV
Condition During cranking

OK:

Voltage and waveform both normal



Result:
Proceed to
OK
NG



OK

INSPECT ENGINE (Pre-ignition, SFI System, Poor Startability)

NG

15.CHECK DATA POINTS (Engine Speed)
a.

Check the RoB data points.

OK:

When "Starter Status"*1 is ON, there is even 1 point at which "Engine Speed" < 300 rpm

* "Starter Status" in the case of other than tandem starter, "Starter Motor Status" in the case of tandem starter (for M15A-FKS)



Result:
Proceed to
OK
NG



OK

NG

16.CHECK OPERATION
16.CHECK OPERATION
a.

Check how long it took the engine to stall after turning the starter off.


Result:
Result Proceed to
After starter turned off, engine immediately stalls.
HINT:

Engine stalls within 2 seconds.


A
After starter turned off, engine stalls after a time. B



A

B