Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › 2020.07–2020.09
RM36W0E _51 Engine / Hybrid System _090986 STOP AND START _0432127 STOP AND START SYSTEM J

STOP AND START  STOP AND START SYSTEM  Starter Signal Circuit  


DESCRIPTION

The engine stop and start ECU uses its internal starter circuit to drive the starter drive relay (ST No. 1 relay) and operate the starter.

WIRING DIAGRAM

for M15A-FKS


A490644E01
5.906,0.375 6.365,0.573 0.458,0.198 10 false A67 6.281,0.365 6.74,0.563 0.458,0.198 10 false +B 5.969,0.198 6.427,0.396 0.458,0.198 10 false 1 4.865,0.552 5.573,0.802 0.708,0.25 10 false EFI NO. 3 3.094,1.125 4.24,1.354 1.146,0.229 10 false EFI-MAIN NO. 1 1.01,0.958 2.156,1.188 1.146,0.229 10 false EFI-MAIN NO. 1 0.146,0.094 2.698,0.438 2.552,0.344 12 false w/ Entry and Start System: 4.083,0.688 4.542,0.885 0.458,0.198 10 false 1 4.094,0.26 4.552,0.458 0.458,0.198 10 false 3 2.969,0.688 3.427,0.885 0.458,0.198 10 false 2 2.958,0.271 3.417,0.469 0.458,0.198 10 false 5 4.448,1.698 5.156,1.948 0.708,0.25 10 false INJ 2.323,1.531 2.781,1.729 0.458,0.198 10 false A54 2.323,1.948 2.781,2.146 0.458,0.198 10 false A54 2.354,1.76 2.813,1.958 0.458,0.198 10 false 13 2.385,1.365 2.844,1.563 0.458,0.198 10 false 2 1.969,1.542 2.427,1.74 0.458,0.198 10 false IGP 1.979,1.927 2.438,2.125 0.458,0.198 10 false IGR 1.552,2.271 2.01,2.469 0.458,0.198 10 false ECM 5.906,3.708 6.365,3.906 0.458,0.198 10 false H43 5.958,3.531 6.417,3.729 0.458,0.198 10 false 21 6.271,3.698 6.729,3.896 0.458,0.198 10 false IGR 6.26,5.167 6.719,5.365 0.458,0.198 10 false IGP 6.094,7.438 7.135,8.198 1.042,0.76 10 false Engine Stop and Start ECU 5.917,5.167 6.375,5.365 0.458,0.198 10 false H43 5.948,4.979 6.406,5.177 0.458,0.198 10 false 18 4.552,5.344 5.698,5.573 1.146,0.229 10 false ECU-IGP NO. 3 3.188,4.406 6.073,4.75 2.885,0.344 10 false Power Distribution Box Assembly 4.042,3 5.188,3.229 1.146,0.229 10 false ECU-IGR NO. 1 4,3.854 5.146,4.083 1.146,0.229 10 false ECU-IGR NO. 4 5.167,2.844 5.625,3.042 0.458,0.198 10 false 4D 5.167,2.677 5.625,2.875 0.458,0.198 10 false 22 5.167,3.708 5.625,3.906 0.458,0.198 10 false 4B 5.156,3.521 5.615,3.719 0.458,0.198 10 false 10 2.823,3.594 3.969,3.823 1.146,0.229 10 false IGR-NO. 1 1.333,4.375 1.792,4.573 0.458,0.198 10 false 4B 1.771,4.375 2.229,4.573 0.458,0.198 10 false 17 0.833,3.417 1.292,3.615 0.458,0.198 10 false 4B 0.865,3.208 1.323,3.406 0.458,0.198 10 false 9 1.427,3.563 1.885,3.76 0.458,0.198 10 false AM2 3.063,5.063 3.521,5.26 0.458,0.198 10 false 3 3.958,5.052 4.417,5.25 0.458,0.198 10 false 5 3.063,5.469 3.521,5.667 0.458,0.198 10 false 1 3.958,5.479 4.417,5.677 0.458,0.198 10 false 2 3.427,5.896 3.885,6.094 0.458,0.198 10 false IGP 3.073,8.344 5.958,8.688 2.885,0.344 10 false Certification ECU (Smart Key ECU Assembly) 3.313,7.219 3.771,7.417 0.458,0.198 10 false IGPD 3.323,7.677 3.781,7.875 0.458,0.198 10 false IGRD 3.333,8.042 3.792,8.24 0.458,0.198 10 false +B 2.927,7.219 3.385,7.417 0.458,0.198 10 false H45 2.927,7.656 3.385,7.854 0.458,0.198 10 false H45 2.938,8.031 3.396,8.229 0.458,0.198 10 false H46 2.969,7.031 3.427,7.229 0.458,0.198 10 false 24 2.969,7.458 3.427,7.656 0.458,0.198 10 false 11 3.01,7.854 3.469,8.052 0.458,0.198 10 false 6 0.958,8.427 2.208,8.813 1.25,0.385 10 false Auxiliary Battery 0.656,7.635 1.813,8.083 1.156,0.448 10 false Fusible Link Block Assembly 0.698,6.708 1.458,7.094 0.76,0.385 10 false BATT-MAIN NO. 1 0.5,6.26 0.958,6.458 0.458,0.198 10 false A81 0.302,6.229 0.76,6.427 0.458,0.198 10 false 1 1.094,5.323 2.063,5.531 0.969,0.208 10 false IGP-MAIN 5.156,4.146 5.615,4.344 0.458,0.198 10 false 4C 5.167,3.969 5.625,4.167 0.458,0.198 10 false 41 0.094,8.531 0.552,8.729 0.458,0.198 10 false A 0.573,8.542 1.031,8.74 0.458,0.198 10 false B 4.292,6.333 4.75,6.531 0.458,0.198 10 false A58 4.281,6.51 6.115,6.896 1.833,0.385 10 false Engine Hood Courtesy Switch (Hood Lock Assembly) 5.667,5.865 6.125,6.063 0.458,0.198 10 false 1 4.365,5.854 4.823,6.052 0.458,0.198 10 false 2 4.552,5.854 5.01,6.052 0.458,0.198 10 false E 5.469,5.865 5.927,6.063 0.458,0.198 10 false + 5.906,5.979 6.365,6.177 0.458,0.198 10 false A67 6.271,5.979 6.729,6.177 0.458,0.198 10 false BNT1 5.979,5.792 6.438,5.99 0.458,0.198 10 false 7 2.073,4.375 2.531,4.573 0.458,0.198 10 false 4C 1.021,4.375 1.479,4.573 0.458,0.198 10 false 11 2.823,4.375 3.281,4.573 0.458,0.198 10 false 4D 2.542,4.375 3,4.573 0.458,0.198 10 false 13 1.5,2.854 1.958,3.052 0.458,0.198 10 false IC 0.844,2.854 1.302,3.052 0.458,0.198 10 false 4H 0.875,2.656 1.333,2.854 0.458,0.198 10 false 1 1.604,6.26 2.063,6.458 0.458,0.198 10 false A80 1.396,6.229 1.854,6.427 0.458,0.198 10 false 1 0.698,7.365 2.115,7.594 1.417,0.229 10 false INP STD NO. 1-3

A490630E01
1.542,3.146 2.219,3.5 0.677,0.354 10 false ST NO. 1 2.052,7.594 3.281,7.792 1.229,0.198 10 false ECM 0.688,8.438 2.885,8.667 2.198,0.229 10 false : CAN Communication Line 2.458,5.302 3.688,5.5 1.229,0.198 10 false ST NO. 1 4.01,2.5 5.24,2.698 1.229,0.198 10 false D45 4.01,2.677 5.333,3.167 1.323,0.49 10 false Park/Neutral Position Switch Assembly*1 0.667,5.021 1.896,5.219 1.229,0.198 10 false Starter Assembly 2.792,7.167 4.021,7.365 1.229,0.198 10 false A54 5.625,6.719 6.854,6.917 1.229,0.198 10 false H43 5.625,7.167 6.854,7.365 1.229,0.198 10 false H43 5.927,7.594 6.969,8.26 1.042,0.667 10 false Engine Stop and Start ECU 4.458,0.542 5.688,0.74 1.229,0.198 10 false BBC NO. 1 4.458,1.125 5.688,1.323 1.229,0.198 10 false BBC NO. 2 5.99,0.406 6.625,0.708 0.635,0.302 10 false BIN1 6,1 6.635,1.302 0.635,0.302 10 false BIN2 6,1.615 6.635,1.917 0.635,0.302 10 false CLL 6,6.042 6.635,6.344 0.635,0.302 10 false DGND 5.99,4.667 6.625,4.969 0.635,0.302 10 false STA 5.615,1.594 6.25,1.896 0.635,0.302 10 false A67 5.615,5.594 6.25,5.896 0.635,0.302 10 false A66 5.615,0.385 6.25,0.688 0.635,0.302 10 false A66 5.615,0.99 6.25,1.292 0.635,0.302 10 false A66 5.615,4.677 6.25,4.979 0.635,0.302 10 false A67 0.521,2.25 1.75,2.448 1.229,0.198 10 false H45 2.281,1.625 3.51,1.823 1.229,0.198 10 false STAR 2.385,1.979 3.615,2.177 1.229,0.198 10 false STA 2.76,1.49 3.99,1.688 1.229,0.198 10 false 10 2.76,1.865 3.99,2.063 1.229,0.198 10 false 3 0.51,4.479 1.74,4.677 1.229,0.198 10 false D80 0.885,4.479 2.115,4.677 1.229,0.198 10 false B 1.229,4.229 2.458,4.427 1.229,0.198 10 false ZYV 1.615,4.625 2.031,4.854 0.417,0.229 10 false D54 0.573,4.292 1.802,4.49 1.229,0.198 10 false 1 2.385,6.281 3.615,6.479 1.229,0.198 10 false STA 2.333,5.854 3.563,6.052 1.229,0.198 10 false NSW 2.281,6.729 3.51,6.927 1.229,0.198 10 false CANH 2.302,7.188 3.531,7.385 1.229,0.198 10 false CANL 5.979,7.188 6.708,7.51 0.729,0.323 10 false CANL 5.969,6.729 6.5,7.01 0.531,0.281 10 false CANH 5.698,0.188 6.198,0.5 0.5,0.313 10 false 3 5.688,0.802 6.188,1.115 0.5,0.313 10 false 1 5.688,1.385 6.188,1.698 0.5,0.313 10 false 17 5.688,5.396 6.198,5.708 0.51,0.313 10 false 2 5.667,4.458 6.167,4.771 0.5,0.313 10 false 21 5.667,6.521 6.167,6.833 0.5,0.313 10 false 13 5.656,6.969 6.156,7.281 0.5,0.313 10 false 14 2.333,4.51 3.563,4.708 1.229,0.198 10 false 3 2.323,4.865 3.552,5.063 1.229,0.198 10 false 1 3.021,4.5 4.25,4.698 1.229,0.198 10 false 5 3.031,4.854 4.26,5.052 1.229,0.198 10 false 2 2.833,5.635 3.333,5.948 0.5,0.313 10 false 23 2.833,6.979 3.333,7.292 0.5,0.313 10 false 25 2.833,6.094 3.333,6.406 0.5,0.313 10 false 30 2.833,6.521 3.333,6.833 0.5,0.313 10 false 26 4.854,0.26 5.354,0.573 0.5,0.313 10 false 2 4.542,0.25 5.042,0.563 0.5,0.313 10 false 1 4.865,0.844 5.365,1.156 0.5,0.313 10 false 2 4.542,0.844 5.042,1.156 0.5,0.313 10 false 1 0.052,0.031 2.208,0.448 2.156,0.417 12 false w/ Entry and Start System: 4.042,4.104 5.271,4.656 1.229,0.552 10 false Clutch Start Switch Assembly*2 0.5,2.438 3.438,2.76 2.938,0.323 10 false Certification ECU (Smart Key ECU Assembly) 2.927,8.302 4.115,8.552 1.188,0.25 10 false *1: for CVT 4.219,8.292 6.104,8.604 1.885,0.313 10 false *2: for Manual Transaxle 1.625,4.24 2.177,4.5 0.552,0.26 10 false D55 1.698,4.042 2.031,4.281 0.333,0.24 10 false 1 5.552,2.146 5.885,2.385 0.333,0.24 10 false *1 5.51,3.542 5.844,3.781 0.333,0.24 10 false *2 1.313,4.615 2.542,4.813 1.229,0.198 10 false ST 2.802,5.823 4.031,6.021 1.229,0.198 10 false A54 2.792,6.281 4.021,6.479 1.229,0.198 10 false A54 2.792,6.729 4.021,6.927 1.229,0.198 10 false A54 6.01,5.594 6.646,5.896 0.635,0.302 10 false GND2 6,5.167 6.635,5.469 0.635,0.302 10 false GND1 5.615,6.042 6.25,6.344 0.635,0.302 10 false A67 5.604,5.167 6.24,5.469 0.635,0.302 10 false A66 5.688,5.823 6.198,6.135 0.51,0.313 10 false 2 5.677,4.979 6.188,5.292 0.51,0.313 10 false 8 4.042,3.917 5.271,4.115 1.229,0.198 10 false A64 3.979,3.552 4.313,3.792 0.333,0.24 10 false *2 5.167,3.542 6.396,3.74 1.229,0.198 10 false 2 4.302,3.552 5.531,3.75 1.229,0.198 10 false 1 3.865,2.135 4.198,2.375 0.333,0.24 10 false *1 5.208,2.125 6.438,2.323 1.229,0.198 10 false 4 4.302,2.115 5.531,2.313 1.229,0.198 10 false 5 4.49,2.115 5.719,2.313 1.229,0.198 10 false L 4.469,3.552 5.698,3.75 1.229,0.198 10 false L 4.979,3.542 6.208,3.74 1.229,0.198 10 false B 4.99,2.135 6.219,2.333 1.229,0.198 10 false B 1.688,4.427 2.021,4.667 0.333,0.24 10 false 1 0.219,0.344 1.448,0.542 1.229,0.198 10 false A 0.219,3.813 1.448,4.01 1.229,0.198 10 false B

A490645E01
5.938,0.375 6.396,0.573 0.458,0.198 10 false A67 6.281,0.365 6.74,0.563 0.458,0.198 10 false +B 6,0.198 6.458,0.396 0.458,0.198 10 false 1 4.708,0.552 5.417,0.802 0.708,0.25 10 false EFI NO. 3 2.76,1.125 3.906,1.354 1.146,0.229 10 false EFI-MAIN NO. 1 0.927,0.958 2.073,1.188 1.146,0.229 10 false EFI-MAIN NO. 1 0.146,0.094 2.698,0.438 2.552,0.344 12 false w/o Entry and Start System: 3.635,0.677 4.094,0.875 0.458,0.198 10 false 1 3.635,0.26 4.094,0.458 0.458,0.198 10 false 3 2.719,0.688 3.177,0.885 0.458,0.198 10 false 2 2.698,0.281 3.156,0.479 0.458,0.198 10 false 5 4.49,1.698 5.198,1.948 0.708,0.25 10 false INJ 2.333,1.552 2.792,1.75 0.458,0.198 10 false A54 2.323,1.969 2.781,2.167 0.458,0.198 10 false A54 2.354,1.792 2.813,1.99 0.458,0.198 10 false 13 2.385,1.365 2.844,1.563 0.458,0.198 10 false 2 1.969,1.542 2.427,1.74 0.458,0.198 10 false IGP 1.979,1.927 2.438,2.125 0.458,0.198 10 false IGR 1.552,2.271 2.01,2.469 0.458,0.198 10 false ECM 5.938,3.302 6.396,3.5 0.458,0.198 10 false H43 5.979,3.125 6.438,3.323 0.458,0.198 10 false 21 6.292,3.313 6.75,3.51 0.458,0.198 10 false IGR 6.292,5.385 6.75,5.583 0.458,0.198 10 false IGP 6.302,7.083 6.76,7.281 0.458,0.198 10 false BNT1 6.083,7.938 7.125,8.698 1.042,0.76 10 false Engine Stop and Start ECU 5.917,5.396 6.375,5.594 0.458,0.198 10 false H43 5.958,5.208 6.417,5.406 0.458,0.198 10 false 18 6,6.917 6.458,7.115 0.458,0.198 10 false 6 4.438,5.583 5.583,5.813 1.146,0.229 10 false ECU-IGP NO. 3 1.552,4.406 4.052,4.813 2.5,0.406 10 false Power Distribution Box Assembly 4.073,2.99 5.219,3.219 1.146,0.229 10 false ECU-IGR NO. 1 4.052,3.438 5.198,3.667 1.146,0.229 10 false ECU-IGR NO. 4 5.229,2.854 5.688,3.052 0.458,0.198 10 false 4D 5.229,2.677 5.688,2.875 0.458,0.198 10 false 22 5.229,3.313 5.688,3.51 0.458,0.198 10 false 4B 5.229,3.115 5.688,3.313 0.458,0.198 10 false 10 2.875,4.042 4.021,4.271 1.146,0.229 10 false IGR-NO. 1 5.229,3.708 5.688,3.906 0.458,0.198 10 false 4C 5.229,3.531 5.688,3.729 0.458,0.198 10 false 17 0.833,3.708 1.292,3.906 0.458,0.198 10 false 4B 0.885,3.531 1.344,3.729 0.458,0.198 10 false 4 1.49,3.844 1.948,4.042 0.458,0.198 10 false AM1 0.833,3.302 1.292,3.5 0.458,0.198 10 false 4H 0.885,3.104 1.344,3.302 0.458,0.198 10 false 1 2.958,5.281 3.417,5.479 0.458,0.198 10 false 3 4.01,5.292 4.469,5.49 0.458,0.198 10 false 5 2.958,4.854 3.417,5.052 0.458,0.198 10 false 2 4.01,4.854 4.469,5.052 0.458,0.198 10 false 1 3.427,5.719 3.885,5.917 0.458,0.198 10 false IGP 3.063,7.094 4.167,7.573 1.104,0.479 10 false Ignition or Starter Switch Assembly 2.979,6.406 3.438,6.604 0.458,0.198 10 false AM1 4.052,6.406 4.51,6.604 0.458,0.198 10 false IG1 3.063,6.917 3.521,7.115 0.458,0.198 10 false H54 4.406,6.406 4.865,6.604 0.458,0.198 10 false 8 2.76,6.406 3.219,6.604 0.458,0.198 10 false 7 0.917,8.385 2.167,8.771 1.25,0.385 10 false Auxiliary Battery 0.49,7.646 2.354,7.958 1.865,0.313 10 false Fusible Link Block Assembly 0.656,7.323 2.021,7.563 1.365,0.24 10 false INP STD NO. 1-3 0.656,6.708 1.896,6.979 1.24,0.271 10 false BATT-MAIN NO. 1 1.813,6.24 2.271,6.438 0.458,0.198 10 false A80 0.469,6.24 0.927,6.438 0.458,0.198 10 false A81 1.615,6.208 2.073,6.406 0.458,0.198 10 false 1 0.271,6.208 0.729,6.406 0.458,0.198 10 false 1 0.74,5.542 1.708,5.75 0.969,0.208 10 false IGP-MAIN 4.146,4.375 4.604,4.573 0.458,0.198 10 false 4D 4.469,4.385 4.927,4.583 0.458,0.198 10 false 13 0.833,4.083 1.292,4.281 0.458,0.198 10 false 4C 0.844,3.917 1.302,4.115 0.458,0.198 10 false 41 0.094,8.5 0.552,8.698 0.458,0.198 10 false A 0.385,8.5 0.844,8.698 0.458,0.198 10 false B 4.25,7.479 4.708,7.677 0.458,0.198 10 false A58 4.24,7.656 6.104,8.031 1.865,0.375 10 false Engine Hood Courtesy Switch (Hood Lock Assembly) 5.938,7.104 6.396,7.302 0.458,0.198 10 false A67 5.698,6.969 6.156,7.167 0.458,0.198 10 false 1 5.469,6.969 5.927,7.167 0.458,0.198 10 false + 4.396,6.99 4.854,7.188 0.458,0.198 10 false 2 4.583,6.99 5.042,7.188 0.458,0.198 10 false E 2.323,8.5 2.781,8.698 0.458,0.198 10 false C 1.573,3.302 2.031,3.5 0.458,0.198 10 false IC

A490631E01
1.375,3.156 2.115,3.427 0.74,0.271 10 false ST NO. 1 2.063,7.906 3.292,8.104 1.229,0.198 10 false ECM 0.688,8.448 2.885,8.677 2.198,0.229 10 false : CAN Communication Line 2.448,5.458 3.677,5.656 1.229,0.198 10 false ST NO. 1 4.177,2.781 5.406,2.979 1.229,0.198 10 false D45 4.167,4.729 5.375,5.188 1.208,0.458 10 false Clutch Start Switch Assembly*2 0.646,5.125 1.875,5.323 1.229,0.198 10 false Starter Assembly 2.771,7.49 4,7.688 1.229,0.198 10 false A54 5.615,6.604 6.844,6.802 1.229,0.198 10 false A67 5.625,7.042 6.854,7.24 1.229,0.198 10 false H43 5.927,7.906 6.99,8.656 1.063,0.75 10 false Engine Stop and Start ECU 4.458,0.542 5.688,0.74 1.229,0.198 10 false BBC NO. 1 4.458,1.125 5.688,1.323 1.229,0.198 10 false BBC NO. 2 5.99,0.385 6.625,0.688 0.635,0.302 10 false BIN1 5.99,1 6.625,1.302 0.635,0.302 10 false BIN2 6,1.604 6.635,1.906 0.635,0.302 10 false CLL 6,5.615 6.635,5.917 0.635,0.302 10 false GND2 6.01,6.594 6.646,6.896 0.635,0.302 10 false STA 5.625,1.604 6.26,1.906 0.635,0.302 10 false A67 5.615,5.198 6.25,5.5 0.635,0.302 10 false A66 5.615,0.385 6.25,0.688 0.635,0.302 10 false A66 5.615,0.99 6.25,1.292 0.635,0.302 10 false A66 5.615,6.073 6.25,6.375 0.635,0.302 10 false A67 2.5,1.99 3.729,2.188 1.229,0.198 10 false H54 2.479,2.156 3.583,2.74 1.104,0.583 10 false Ignition or Starter Switch Assembly 2.583,1.458 3.813,1.656 1.229,0.198 10 false AM2 3.281,1.458 4.51,1.656 1.229,0.198 10 false ST2 2.375,1.448 3.604,1.646 1.229,0.198 10 false 1 3.646,1.448 4.875,1.646 1.229,0.198 10 false 4 0.479,4.76 1.708,4.958 1.229,0.198 10 false D80 0.844,4.771 2.073,4.969 1.229,0.198 10 false B 1.188,4.26 2.417,4.458 1.229,0.198 10 false ZYV 1.604,4.771 2.833,4.969 1.229,0.198 10 false D54 0.542,4.563 1.771,4.76 1.229,0.198 10 false 1 2.375,6.656 3.604,6.854 1.229,0.198 10 false STA 2.333,6.156 3.563,6.354 1.229,0.198 10 false NSW 2.281,7.063 3.51,7.26 1.229,0.198 10 false CANH 2.292,7.51 3.521,7.708 1.229,0.198 10 false CANL 5.979,7.469 6.708,7.792 0.729,0.323 10 false CANL 6,7.042 6.531,7.323 0.531,0.281 10 false CANH 5.698,0.188 6.198,0.5 0.5,0.313 10 false 3 5.688,0.802 6.188,1.115 0.5,0.313 10 false 1 5.688,1.385 6.188,1.698 0.5,0.313 10 false 17 5.688,5 6.198,5.313 0.51,0.313 10 false 8 5.698,5.885 6.198,6.198 0.5,0.313 10 false 6 5.656,6.844 6.156,7.156 0.5,0.313 10 false 13 5.656,7.281 6.156,7.594 0.5,0.313 10 false 14 2.313,4.646 3.542,4.844 1.229,0.198 10 false 3 2.313,5 3.542,5.198 1.229,0.198 10 false 1 3.031,4.656 4.26,4.854 1.229,0.198 10 false 5 3.021,4.99 4.25,5.188 1.229,0.198 10 false 2 2.823,6.417 3.323,6.729 0.5,0.313 10 false 30 2.823,5.958 3.323,6.271 0.5,0.313 10 false 23 2.823,6.854 3.323,7.167 0.5,0.313 10 false 26 4.854,0.26 5.354,0.573 0.5,0.313 10 false 2 4.542,0.25 5.042,0.563 0.5,0.313 10 false 1 4.865,0.844 5.365,1.156 0.5,0.313 10 false 2 4.542,0.844 5.042,1.156 0.5,0.313 10 false 1 1.719,1.771 2.948,1.969 1.229,0.198 10 false AM2 4.177,2.969 5.49,3.365 1.313,0.396 10 false Park/Neutral Position Switch Assembly*1 3.01,8.417 3.948,8.729 0.938,0.313 10 false *1: for CVT 4.115,8.396 5.698,8.75 1.583,0.354 10 false *2: for Manual Transaxle 0.083,0.042 2.438,0.344 2.354,0.302 12 false w/o Entry and Start System: 4.177,4.552 5.406,4.75 1.229,0.198 10 false A64 1.594,4.25 2.823,4.448 1.229,0.198 10 false D55 1.667,4.563 2.896,4.76 1.229,0.198 10 false 1 5.531,2.396 6.76,2.594 1.229,0.198 10 false *1 5.531,4.135 6.76,4.333 1.229,0.198 10 false *2 1.302,4.75 2.531,4.948 1.229,0.198 10 false ST 2.823,7.292 3.323,7.604 0.5,0.313 10 false 25 2.781,7.052 4.01,7.25 1.229,0.198 10 false A54 2.792,6.604 4.021,6.802 1.229,0.198 10 false A54 2.792,6.146 4.021,6.344 1.229,0.198 10 false A54 4.073,2.406 5.302,2.604 1.229,0.198 10 false *1 4.125,4.146 5.354,4.344 1.229,0.198 10 false *2 5.083,2.417 6.313,2.615 1.229,0.198 10 false B 5.031,4.146 6.26,4.344 1.229,0.198 10 false B 4.531,4.146 5.76,4.344 1.229,0.198 10 false L 4.604,2.417 5.833,2.615 1.229,0.198 10 false L 4.396,2.406 5.625,2.604 1.229,0.198 10 false 5 5.313,2.406 6.542,2.604 1.229,0.198 10 false 4 5.25,4.156 6.479,4.354 1.229,0.198 10 false 2 4.354,4.156 5.583,4.354 1.229,0.198 10 false 1 1.667,4.052 2.896,4.25 1.229,0.198 10 false 1 5.615,7.479 6.844,7.677 1.229,0.198 10 false H43 5.656,6.396 6.156,6.708 0.5,0.313 10 false 21 5.615,5.625 6.25,5.927 0.635,0.302 10 false A66 6,6.063 6.635,6.365 0.635,0.302 10 false DGND 6,5.208 6.635,5.51 0.635,0.302 10 false GND1 5.688,5.427 6.917,5.625 1.229,0.198 10 false 2 0.219,0.625 0.719,0.938 0.5,0.313 10 false A 0.229,3.813 0.729,4.125 0.5,0.313 10 false B 1.063,0.635 1.563,0.948 0.5,0.313 10 false C


for 1KR-FE


A490644E02
5.906,0.375 6.365,0.573 0.458,0.198 10 false A67 6.281,0.365 6.74,0.563 0.458,0.198 10 false +B 5.969,0.198 6.427,0.396 0.458,0.198 10 false 1 4.865,0.552 5.573,0.802 0.708,0.25 10 false EFI NO. 3 3.104,1.125 4.25,1.354 1.146,0.229 10 false EFI-MAIN NO. 1 0.927,0.958 2.073,1.188 1.146,0.229 10 false EFI-MAIN NO. 1 0.146,0.094 2.698,0.438 2.552,0.344 12 false w/ Entry and Start System: 4.104,0.688 4.563,0.885 0.458,0.198 10 false 1 2.958,0.26 3.417,0.458 0.458,0.198 10 false 3 2.948,0.688 3.406,0.885 0.458,0.198 10 false 2 4.104,0.26 4.563,0.458 0.458,0.198 10 false 5 4.448,1.698 5.156,1.948 0.708,0.25 10 false INJ 2.323,1.531 2.781,1.729 0.458,0.198 10 false A55 2.323,1.948 2.781,2.146 0.458,0.198 10 false A55 2.354,1.76 2.813,1.958 0.458,0.198 10 false 31 2.354,1.344 2.813,1.542 0.458,0.198 10 false 37 1.823,1.542 2.281,1.74 0.458,0.198 10 false IGSW 1.979,1.927 2.438,2.125 0.458,0.198 10 false IGR 1.552,2.271 2.01,2.469 0.458,0.198 10 false ECM 5.906,3.708 6.365,3.906 0.458,0.198 10 false H43 5.958,3.531 6.417,3.729 0.458,0.198 10 false 21 6.271,3.698 6.729,3.896 0.458,0.198 10 false IGR 6.26,5.167 6.719,5.365 0.458,0.198 10 false IGP 6.094,7.438 7.135,8.198 1.042,0.76 10 false Engine Stop and Start ECU 5.917,5.167 6.375,5.365 0.458,0.198 10 false H43 5.948,4.979 6.406,5.177 0.458,0.198 10 false 18 4.552,5.344 5.698,5.573 1.146,0.229 10 false ECU-IGP NO. 3 3.188,4.417 6.073,4.76 2.885,0.344 10 false Power Distribution Box Assembly 4.042,3.031 5.188,3.26 1.146,0.229 10 false ECU-IGR NO. 1 4,3.875 5.146,4.104 1.146,0.229 10 false ECU-IGR NO. 4 5.167,2.844 5.625,3.042 0.458,0.198 10 false 4D 5.167,2.677 5.625,2.875 0.458,0.198 10 false 22 5.167,3.708 5.625,3.906 0.458,0.198 10 false 4B 5.156,3.521 5.615,3.719 0.458,0.198 10 false 10 2.823,3.594 3.969,3.823 1.146,0.229 10 false IGR-NO. 1 2.073,4.375 2.531,4.573 0.458,0.198 10 false 4C 1.781,4.375 2.24,4.573 0.458,0.198 10 false 17 0.833,3.417 1.292,3.615 0.458,0.198 10 false 4B 0.885,3.219 1.344,3.417 0.458,0.198 10 false 9 1.427,3.563 1.885,3.76 0.458,0.198 10 false AM2 3.073,5.052 3.531,5.25 0.458,0.198 10 false 3 3.969,5.052 4.427,5.25 0.458,0.198 10 false 5 3.073,5.479 3.531,5.677 0.458,0.198 10 false 1 3.969,5.479 4.427,5.677 0.458,0.198 10 false 2 3.448,5.896 3.906,6.094 0.458,0.198 10 false IGP 3.073,8.365 5.958,8.708 2.885,0.344 10 false Certification ECU (Smart Key ECU Assembly) 3.313,7.219 3.771,7.417 0.458,0.198 10 false IGPD 3.313,7.646 3.771,7.844 0.458,0.198 10 false IGRD 3.333,8.042 3.792,8.24 0.458,0.198 10 false +B 2.927,7.219 3.385,7.417 0.458,0.198 10 false H45 2.927,7.656 3.385,7.854 0.458,0.198 10 false H45 2.938,8.031 3.396,8.229 0.458,0.198 10 false H46 2.969,7.031 3.427,7.229 0.458,0.198 10 false 24 2.969,7.458 3.427,7.656 0.458,0.198 10 false 11 3.01,7.854 3.469,8.052 0.458,0.198 10 false 6 0.958,8.438 2.208,8.823 1.25,0.385 10 false Auxiliary Battery 0.708,7.646 1.917,8.052 1.208,0.406 10 false Fusible Link Block Assembly 0.698,6.74 1.448,7.146 0.75,0.406 10 false BATT-MAIN NO. 1 0.51,6.26 0.969,6.458 0.458,0.198 10 false A81 0.302,6.219 0.76,6.417 0.458,0.198 10 false 1 1.094,5.313 2.063,5.521 0.969,0.208 10 false IGP-MAIN 5.156,4.146 5.615,4.344 0.458,0.198 10 false 4C 5.167,3.969 5.625,4.167 0.458,0.198 10 false 41 0.094,8.531 0.552,8.729 0.458,0.198 10 false A 0.573,8.542 1.031,8.74 0.458,0.198 10 false B 4.292,6.333 4.75,6.531 0.458,0.198 10 false A58 4.281,6.51 6.115,6.896 1.833,0.385 10 false Engine Hood Courtesy Switch (Hood Lock Assembly) 5.667,5.865 6.125,6.063 0.458,0.198 10 false 1 4.365,5.854 4.823,6.052 0.458,0.198 10 false 2 4.552,5.854 5.01,6.052 0.458,0.198 10 false E 5.469,5.865 5.927,6.063 0.458,0.198 10 false + 5.906,5.979 6.365,6.177 0.458,0.198 10 false A67 6.271,5.979 6.729,6.177 0.458,0.198 10 false BNT1 5.979,5.792 6.438,5.99 0.458,0.198 10 false 7 2.833,4.375 3.292,4.573 0.458,0.198 10 false 4D 2.531,4.375 2.99,4.573 0.458,0.198 10 false 13 1.344,4.375 1.802,4.573 0.458,0.198 10 false 4B 1.031,4.375 1.49,4.573 0.458,0.198 10 false 11 0.74,7.375 2.24,7.667 1.5,0.292 10 false INP STD NO. 1-3 1.51,2.854 1.969,3.052 0.458,0.198 10 false IC 0.844,2.844 1.302,3.042 0.458,0.198 10 false 4H 0.875,2.656 1.333,2.854 0.458,0.198 10 false 1 1.604,6.26 2.063,6.458 0.458,0.198 10 false A80 1.396,6.229 1.854,6.427 0.458,0.198 10 false 1

A490632E01
1.365,3.146 2.042,3.5 0.677,0.354 10 false ST NO. 1 2.094,7.583 3.323,7.781 1.229,0.198 10 false ECM 0.688,8.438 2.885,8.667 2.198,0.229 10 false : CAN Communication Line 2.438,5.323 3.667,5.521 1.229,0.198 10 false ST NO. 1 0.667,5.021 1.896,5.219 1.229,0.198 10 false Starter Assembly 2.813,7.177 4.042,7.375 1.229,0.198 10 false A55 5.635,6.729 6.865,6.927 1.229,0.198 10 false H43 5.625,7.156 6.854,7.354 1.229,0.198 10 false H43 5.927,7.583 6.969,8.25 1.042,0.667 10 false Engine Stop and Start ECU 4.458,0.542 5.688,0.74 1.229,0.198 10 false BBC NO. 1 4.458,1.125 5.688,1.323 1.229,0.198 10 false BBC NO. 2 5.99,0.406 6.625,0.708 0.635,0.302 10 false BIN1 6,1 6.635,1.302 0.635,0.302 10 false BIN2 6,1.615 6.635,1.917 0.635,0.302 10 false CLL 5.99,6.031 6.625,6.333 0.635,0.302 10 false DGND 6,4.667 6.635,4.969 0.635,0.302 10 false STA 5.615,1.594 6.25,1.896 0.635,0.302 10 false A67 5.625,5.604 6.26,5.906 0.635,0.302 10 false A66 5.615,0.385 6.25,0.688 0.635,0.302 10 false A66 5.615,0.99 6.25,1.292 0.635,0.302 10 false A66 5.625,4.677 6.26,4.979 0.635,0.302 10 false A67 0.521,2.25 1.75,2.448 1.229,0.198 10 false H45 2.281,1.625 3.51,1.823 1.229,0.198 10 false STAR 2.385,1.979 3.615,2.177 1.229,0.198 10 false STA 2.76,1.49 3.99,1.688 1.229,0.198 10 false 10 2.76,1.865 3.99,2.063 1.229,0.198 10 false 3 0.51,4.479 1.74,4.677 1.229,0.198 10 false D80 0.885,4.49 2.115,4.688 1.229,0.198 10 false B 1.625,4.625 2.042,4.854 0.417,0.229 10 false D54 2.375,6.271 3.604,6.469 1.229,0.198 10 false STA 2.333,5.833 3.563,6.031 1.229,0.198 10 false NSW 2.281,6.729 3.51,6.927 1.229,0.198 10 false CANH 2.292,7.167 3.521,7.365 1.229,0.198 10 false CANL 6,7.167 6.729,7.49 0.729,0.323 10 false CANL 5.99,6.708 6.521,6.99 0.531,0.281 10 false CANH 5.698,0.188 6.198,0.5 0.5,0.313 10 false 3 5.688,0.802 6.188,1.115 0.5,0.313 10 false 1 5.688,1.385 6.188,1.698 0.5,0.313 10 false 17 5.698,5.417 6.208,5.729 0.51,0.313 10 false 2 5.667,4.479 6.167,4.792 0.5,0.313 10 false 21 5.667,6.531 6.167,6.844 0.5,0.313 10 false 13 5.667,6.969 6.167,7.281 0.5,0.313 10 false 14 2.323,4.5 3.552,4.698 1.229,0.198 10 false 3 2.313,4.854 3.542,5.052 1.229,0.198 10 false 1 3.031,4.49 4.26,4.688 1.229,0.198 10 false 5 3.031,4.844 4.26,5.042 1.229,0.198 10 false 2 2.781,5.635 3.281,5.948 0.5,0.313 10 false 111 2.833,6.979 3.333,7.292 0.5,0.313 10 false 25 2.823,6.073 3.323,6.385 0.5,0.313 10 false 46 2.833,6.531 3.333,6.844 0.5,0.313 10 false 26 4.854,0.26 5.354,0.573 0.5,0.313 10 false 2 4.542,0.25 5.042,0.563 0.5,0.313 10 false 1 4.865,0.844 5.365,1.156 0.5,0.313 10 false 2 4.542,0.844 5.042,1.156 0.5,0.313 10 false 1 0.052,0.031 2.208,0.448 2.156,0.417 12 false w/ Entry and Start System: 3.99,3.646 5.906,3.938 1.917,0.292 10 false Clutch Start Switch Assembly 0.5,2.438 3.438,2.76 2.938,0.323 10 false Certification ECU (Smart Key ECU Assembly) 1.323,4.615 2.552,4.813 1.229,0.198 10 false ST 2.802,5.833 4.031,6.031 1.229,0.198 10 false D50 2.802,6.281 4.031,6.479 1.229,0.198 10 false A55 2.792,6.729 4.021,6.927 1.229,0.198 10 false A55 6.01,5.604 6.646,5.906 0.635,0.302 10 false GND2 6,5.167 6.635,5.469 0.635,0.302 10 false GND1 5.625,6.052 6.26,6.354 0.635,0.302 10 false A67 5.604,5.177 6.24,5.479 0.635,0.302 10 false A66 5.688,5.854 6.198,6.167 0.51,0.313 10 false 6 5.698,4.99 6.208,5.302 0.51,0.313 10 false 8 4,3.438 5.229,3.635 1.229,0.198 10 false A64 5.188,3.094 6.417,3.292 1.229,0.198 10 false 2 4.219,3.094 5.448,3.292 1.229,0.198 10 false 1 4.469,3.094 5.698,3.292 1.229,0.198 10 false L 4.969,3.104 6.198,3.302 1.229,0.198 10 false B 1.688,4.438 2.021,4.677 0.333,0.24 10 false 1 0.219,0.708 1.448,0.906 1.229,0.198 10 false A 0.219,3.813 1.448,4.01 1.229,0.198 10 false B 0.563,4.271 1.792,4.469 1.229,0.198 10 false 1

A490645E02
5.938,0.375 6.396,0.573 0.458,0.198 10 false A67 6.281,0.365 6.74,0.563 0.458,0.198 10 false +B 6,0.198 6.458,0.396 0.458,0.198 10 false 1 4.708,0.552 5.417,0.802 0.708,0.25 10 false EFI NO. 3 2.771,1.125 3.917,1.354 1.146,0.229 10 false EFI-MAIN NO. 1 0.927,0.958 2.073,1.188 1.146,0.229 10 false EFI-MAIN NO. 1 0.146,0.094 2.698,0.438 2.552,0.344 12 false w/o Entry and Start System: 3.635,0.677 4.094,0.875 0.458,0.198 10 false 1 2.719,0.26 3.177,0.458 0.458,0.198 10 false 3 2.719,0.688 3.177,0.885 0.458,0.198 10 false 2 3.635,0.25 4.094,0.448 0.458,0.198 10 false 5 4.49,1.698 5.198,1.948 0.708,0.25 10 false INJ 2.333,1.552 2.792,1.75 0.458,0.198 10 false A55 2.323,1.969 2.781,2.167 0.458,0.198 10 false A55 2.354,1.792 2.813,1.99 0.458,0.198 10 false 31 2.365,1.365 2.823,1.563 0.458,0.198 10 false 37 1.833,1.542 2.292,1.74 0.458,0.198 10 false IGSW 1.979,1.927 2.438,2.125 0.458,0.198 10 false IGR 1.552,2.271 2.01,2.469 0.458,0.198 10 false ECM 5.938,3.302 6.396,3.5 0.458,0.198 10 false H43 5.979,3.125 6.438,3.323 0.458,0.198 10 false 21 6.292,3.313 6.75,3.51 0.458,0.198 10 false IGR 6.292,5.385 6.75,5.583 0.458,0.198 10 false IGP 6.302,7.083 6.76,7.281 0.458,0.198 10 false BNT1 6.083,7.938 7.125,8.698 1.042,0.76 10 false Engine Stop and Start ECU 5.917,5.396 6.375,5.594 0.458,0.198 10 false H43 5.958,5.208 6.417,5.406 0.458,0.198 10 false 18 6,6.917 6.458,7.115 0.458,0.198 10 false 6 4.438,5.583 5.583,5.813 1.146,0.229 10 false ECU-IGP NO. 3 1.177,4.417 4.063,4.76 2.885,0.344 10 false Instrument Panel Junction Block Assembly 4.042,3.01 5.188,3.24 1.146,0.229 10 false ECU-IGR NO. 1 4.042,3.469 5.188,3.698 1.146,0.229 10 false ECU-IGR NO. 4 5.229,2.854 5.688,3.052 0.458,0.198 10 false 4D 5.229,2.677 5.688,2.875 0.458,0.198 10 false 22 5.229,3.313 5.688,3.51 0.458,0.198 10 false 4B 5.229,3.115 5.688,3.313 0.458,0.198 10 false 10 2.875,4.01 4.021,4.24 1.146,0.229 10 false IGR-NO. 1 5.229,3.708 5.688,3.906 0.458,0.198 10 false 4C 5.229,3.531 5.688,3.729 0.458,0.198 10 false 17 0.833,3.708 1.292,3.906 0.458,0.198 10 false 4B 0.885,3.531 1.344,3.729 0.458,0.198 10 false 4 1.5,3.865 1.958,4.063 0.458,0.198 10 false AM1 0.833,3.302 1.292,3.5 0.458,0.198 10 false 4H 0.885,3.104 1.344,3.302 0.458,0.198 10 false 1 2.948,5.271 3.406,5.469 0.458,0.198 10 false 3 3.979,5.271 4.438,5.469 0.458,0.198 10 false 5 2.948,4.844 3.406,5.042 0.458,0.198 10 false 2 3.979,4.844 4.438,5.042 0.458,0.198 10 false 1 3.427,5.75 3.885,5.948 0.458,0.198 10 false IGP 3.083,7.104 4.188,7.583 1.104,0.479 10 false Ignition or Starter Switch Assembly 3.01,6.406 3.469,6.604 0.458,0.198 10 false AM1 4.042,6.406 4.5,6.604 0.458,0.198 10 false IG1 3.083,6.938 3.542,7.135 0.458,0.198 10 false H54 4.406,6.396 4.865,6.594 0.458,0.198 10 false 8 2.76,6.417 3.219,6.615 0.458,0.198 10 false 7 0.917,8.375 2.167,8.76 1.25,0.385 10 false Auxiliary Battery 0.51,7.646 2.667,8.031 2.156,0.385 10 false Fusible Link Block Assembly 0.625,7.333 1.99,7.573 1.365,0.24 10 false INP STD NO. 1-3 0.667,6.677 1.854,7.083 1.188,0.406 10 false BATT-MAIN NO. 1 1.813,6.24 2.271,6.438 0.458,0.198 10 false A80 0.469,6.24 0.927,6.438 0.458,0.198 10 false A81 1.604,6.208 2.063,6.406 0.458,0.198 10 false 1 0.271,6.208 0.729,6.406 0.458,0.198 10 false 1 0.729,5.542 1.698,5.75 0.969,0.208 10 false IGP-MAIN 4.146,4.375 4.604,4.573 0.458,0.198 10 false 4D 4.469,4.385 4.927,4.583 0.458,0.198 10 false 13 0.833,4.083 1.292,4.281 0.458,0.198 10 false 4C 0.844,3.917 1.302,4.115 0.458,0.198 10 false 41 0.094,8.5 0.552,8.698 0.458,0.198 10 false A 0.385,8.5 0.844,8.698 0.458,0.198 10 false B 4.25,7.479 4.708,7.677 0.458,0.198 10 false A58 4.24,7.656 6.104,8.031 1.865,0.375 10 false Engine Hood Courtesy Switch (Hood Lock Assembly) 5.938,7.104 6.396,7.302 0.458,0.198 10 false A67 5.698,6.979 6.156,7.177 0.458,0.198 10 false 1 5.469,6.969 5.927,7.167 0.458,0.198 10 false + 4.396,6.979 4.854,7.177 0.458,0.198 10 false 2 4.583,6.979 5.042,7.177 0.458,0.198 10 false E 2.313,8.5 2.771,8.698 0.458,0.198 10 false C 1.563,3.302 2.021,3.5 0.458,0.198 10 false IC

A490633E01
1.375,3.156 2.115,3.427 0.74,0.271 10 false ST NO. 1 2.063,7.906 3.292,8.104 1.229,0.198 10 false ECM 0.688,8.448 2.885,8.677 2.198,0.229 10 false : CAN Communication Line 2.458,5.458 3.688,5.656 1.229,0.198 10 false ST NO. 1 4.271,4.229 5.479,4.802 1.208,0.573 10 false Clutch Start Switch Assembly 0.646,5.104 1.875,5.302 1.229,0.198 10 false Starter Assembly 2.771,7.479 4,7.677 1.229,0.198 10 false A55 5.615,6.604 6.844,6.802 1.229,0.198 10 false A67 5.625,7.042 6.854,7.24 1.229,0.198 10 false H43 5.927,7.906 6.99,8.656 1.063,0.75 10 false Engine Stop and Start ECU 4.458,0.542 5.688,0.74 1.229,0.198 10 false BBC NO. 1 4.458,1.125 5.688,1.323 1.229,0.198 10 false BBC NO. 2 5.99,0.385 6.625,0.688 0.635,0.302 10 false BIN1 5.99,1 6.625,1.302 0.635,0.302 10 false BIN2 6,1.604 6.635,1.906 0.635,0.302 10 false CLL 6,5.615 6.635,5.917 0.635,0.302 10 false GND2 6.01,6.594 6.646,6.896 0.635,0.302 10 false STA 5.625,1.604 6.26,1.906 0.635,0.302 10 false A67 5.615,5.198 6.25,5.5 0.635,0.302 10 false A66 5.625,0.385 6.26,0.688 0.635,0.302 10 false A66 5.625,1 6.26,1.302 0.635,0.302 10 false A66 5.615,6.073 6.25,6.375 0.635,0.302 10 false A67 2.5,1.99 3.729,2.188 1.229,0.198 10 false H54 2.479,2.156 3.583,2.74 1.104,0.583 10 false Ignition or Starter Switch Assembly 2.583,1.458 3.813,1.656 1.229,0.198 10 false AM2 3.302,1.469 4.531,1.667 1.229,0.198 10 false ST2 2.375,1.448 3.604,1.646 1.229,0.198 10 false 1 3.646,1.448 4.875,1.646 1.229,0.198 10 false 4 0.479,4.76 1.708,4.958 1.229,0.198 10 false D80 0.844,4.75 2.073,4.948 1.229,0.198 10 false B 1.604,4.771 2.833,4.969 1.229,0.198 10 false D54 0.542,4.573 1.771,4.771 1.229,0.198 10 false 1 2.375,6.656 3.604,6.854 1.229,0.198 10 false STA 2.333,6.156 3.563,6.354 1.229,0.198 10 false NSW 2.281,7.063 3.51,7.26 1.229,0.198 10 false CANH 2.292,7.51 3.521,7.708 1.229,0.198 10 false CANL 5.979,7.469 6.708,7.792 0.729,0.323 10 false CANL 6,7.042 6.531,7.323 0.531,0.281 10 false CANH 5.698,0.188 6.198,0.5 0.5,0.313 10 false 3 5.688,0.802 6.188,1.115 0.5,0.313 10 false 1 5.688,1.385 6.188,1.698 0.5,0.313 10 false 17 5.688,5 6.198,5.313 0.51,0.313 10 false 8 5.698,5.885 6.198,6.198 0.5,0.313 10 false 6 5.656,6.844 6.156,7.156 0.5,0.313 10 false 13 5.656,7.281 6.156,7.594 0.5,0.313 10 false 14 2.313,4.615 3.542,4.813 1.229,0.198 10 false 3 2.302,4.99 3.531,5.188 1.229,0.198 10 false 1 3.042,4.625 4.271,4.823 1.229,0.198 10 false 5 3.042,4.99 4.271,5.188 1.229,0.198 10 false 2 2.823,6.417 3.323,6.729 0.5,0.313 10 false 46 2.781,5.958 3.281,6.271 0.5,0.313 10 false 111 2.823,6.854 3.323,7.167 0.5,0.313 10 false 26 4.854,0.26 5.354,0.573 0.5,0.313 10 false 2 4.542,0.25 5.042,0.563 0.5,0.313 10 false 1 4.865,0.844 5.365,1.156 0.5,0.313 10 false 2 4.542,0.844 5.042,1.156 0.5,0.313 10 false 1 1.719,1.771 2.948,1.969 1.229,0.198 10 false AM2 0.083,0.042 2.438,0.344 2.354,0.302 12 false w/o Entry and Start System: 4.271,4.042 5.5,4.24 1.229,0.198 10 false A64 1.667,4.552 2.896,4.75 1.229,0.198 10 false 1 1.292,4.76 2.521,4.958 1.229,0.198 10 false ST 2.823,7.292 3.323,7.604 0.5,0.313 10 false 25 2.781,7.052 4.01,7.25 1.229,0.198 10 false A55 2.792,6.604 4.021,6.802 1.229,0.198 10 false A55 2.792,6.146 4.021,6.344 1.229,0.198 10 false D50 5.042,3.573 6.271,3.771 1.229,0.198 10 false B 4.531,3.573 5.76,3.771 1.229,0.198 10 false L 5.25,3.573 6.479,3.771 1.229,0.198 10 false 2 4.313,3.573 5.542,3.771 1.229,0.198 10 false 1 5.615,7.479 6.844,7.677 1.229,0.198 10 false H43 5.656,6.396 6.156,6.708 0.5,0.313 10 false 21 5.615,5.625 6.25,5.927 0.635,0.302 10 false A66 6,6.063 6.635,6.365 0.635,0.302 10 false DGND 6,5.208 6.635,5.51 0.635,0.302 10 false GND1 5.688,5.427 6.917,5.625 1.229,0.198 10 false 2 0.229,0.646 1.458,0.844 1.229,0.198 10 false A 1.063,0.635 2.292,0.833 1.229,0.198 10 false C


CAUTION / NOTICE / HINT

·

When the engine stop and start ECU is replaced, read the number of starter operations before replacement and record this number to the new engine stop and start ECU after replacement.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

When the engine stop ECU has been replaced, perform external backup boost converter (Eco run vehicle converter assembly) existence learning.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioner amplifier assembly, perform initialization/learning of the air conditioner information for the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

When the starter assembly is replaced, the number of starter operations stored in the engine stop and start ECU must be reset.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

for CVT:

When the engine stop and start ECU or oil pump with motor assembly is replaced, check the oil pump with motor assembly.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

When the starter assembly is replaced, "ST NO. 1 relay" must be also replaced.

·

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

For wire harness and connector inspection procedures and precautions, refer toGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


PROCEDURE

1.CHECK CRANKING
a.

Turn the ignition switch to ON and check that the engine cranks.


Result:
Result Proceed to
Engine cranks A
Engine does not crank B



A

2.PERFORM ACTIVE TEST USING GTS (STARTER(HOOD CLOSE))

B

20.READ VALUE USING GTS (STARTER(HOOD CLOSE))
2.PERFORM ACTIVE TEST USING GTS (STARTER(HOOD CLOSE))
a.

Using the GTS, perform Active Test.

Powertrain > Stop and Start > Active Test
Tester Display
Starter(Hood Close)
50004 392 42017

b.

Check whether the engine cranks while the Active Test "Starter(Hood Close)" is being performed.

NOTICE:

The Active Test "Starter(Hood Close)" is stopped automatically 3 seconds after the starter assembly begins operating.


Standard:

Engine cranks



Result:
Result Proceed to
Engine cranks A
Engine does not crank B



A

3.CHECK VEHICLE CONTROL HISTORY (ENGINE CONTROL SYSTEM)

B

14.CHECK HARNESS AND CONNECTOR (STA SIGNAL)
3.CHECK VEHICLE CONTROL HISTORY (ENGINE CONTROL SYSTEM)
a.

Enter the following menus.

Powertrain > Engine > Utility
Tester Display
Vehicle Control History (RoB)
50005 372 55

b.

Check the vehicle control history (RoB).

Result:
Result Proceed to
Engine control system Vehicle Control History (RoB) is not output A
Engine Difficult to Start is output B
Result other than Engine Difficult to Start is output C


HINT:
·

If the value of "Cranking Time" is approximately 1.5 seconds, the stop and start control system or starter system may be malfunctioning.

·

If the value of "Cranking Time" is small (approximately 0.5 seconds or less: the minimum value varies depending on the model), the engine control system may be malfunctioning.

·

The Data List item "Cranking Time" indicates the length of time starter operation is requested by the engine stop and start ECU. If the engine speed exceeds the specified value, the engine stop and start ECU cancels its start request.





A

4.CHECK VEHICLE CONTROL HISTORY

B

6.CHECK VEHICLE CONTROL HISTORY (ENGINE CONTROL SYSTEM)

C

4.CHECK VEHICLE CONTROL HISTORY
a.

Enter the following menus.

Powertrain > Stop and Start > Utility
Tester Display
Vehicle Control History (RoB)
50005 392 55

b.

Select a vehicle control history item to display the data from the time of control.


c.

Check the output data.

Result:
Tester Display Result Proceed to
Engine Stall History during Stop&Start (Collision or Battery Voltage Low) Yes A
Engine Stall History during Engine Starting (Collision) Yes
Engine Start Fail Yes B
Vehicle control history item is not output or No is displayed for the results of all of the freeze frame data above




A

5.CHECK VEHICLE CONDITION (COLLISION HISTORY)

B

7.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST RELAY)
5.CHECK VEHICLE CONDITION (COLLISION HISTORY)
a.

Check if the vehicle was in a collision when the engine stalled.

Result:
Result Proceed to
Vehicle was in collision when engine stalled A
Vehicle was not in collision when engine stalled B


HINT:

When "Engine Stall History during Stop&Start (Collision or Battery Voltage Low)" or "Engine Stall History during Engine Starting (Collision)" is stored:

This may have been stored because the vehicle was in a collision or a collision detection signal was input while stop and start control was operating.




A

END (ENGINE STALLED BECAUSE COLLISION DETECTION SIGNAL WAS RECEIVED)

B

6.CHECK VEHICLE CONTROL HISTORY (ENGINE CONTROL SYSTEM)
a.

Enter the following menus.

Powertrain > Engine > Utility
Tester Display
Vehicle Control History (RoB)
50005 372 55

b.

Select Engine Difficult to Start from the Vehicle Control History to display the data from the time of control.


c.

Check the output data.

HINT:
·

Checking the freeze frame data allows the vehicle conditions at the time of detection to be confirmed.

·

As Vehicle Control History may be overwritten whenever the trigger conditions are met, make sure to save the Vehicle Control History data before performing any inspections.




Result:
Result Proceed to
Engine speed does not rise to approximately 300 rpm (Starter does not rotate) A
Engine speed rises to approximately 300 rpm (Starter rotates) B



A

4.CHECK VEHICLE CONTROL HISTORY

B

7.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST RELAY)
a.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.*1

*1: w/ Entry and Start System



b.

Disconnect the D45 park/neutral position switch assembly connector.*1

*1: for CVT



c.

Disconnect the A64 clutch start switch assembly connector.*1

*1: for Manual Transaxle



d.

Disconnect the A54*1 or A55*2 ECM connector.

*1: for M15A-FKS

*2: for 1KR-FE



e.

Disconnect the A67 engine stop and start ECU connector.


f.

Remove the ST NO. 1 relay from the NO. 1 engine room relay block and junction block assembly


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A67-21 (STA) - 1 (ST relay holder) Always Below 1 Ω
A67-21 (STA) - Body ground Always 10 kΩ or higher
1 (ST relay holder) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)
a.

Remove the ST relay from the NO. 1 engine room relay block and junction block assembly


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 2 - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (for M15A-FKS) A
OK (for 1KR-FE) B
NG C



A

9.CHECK HARNESS AND CONNECTOR (ST RELAY - AUXILIARY BATTERY)

B

15.CHECK HARNESS AND CONNECTOR (ST RELAY - AUXILIARY BATTERY)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (ST RELAY - AUXILIARY BATTERY)
a.

Remove the ST relay from the NO. 1 engine room relay block and junction block assembly


b.
A456535C01
0.125,0.083 0.438,0.24 0.313,0.156 10 false *1 2.198,0.354 2.51,0.51 0.313,0.156 10 false *a
*1 No. 1 Engine Room Relay Block
*a ST NO. 1 Relay Holder


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
ST relay terminal 5 - Body ground Always 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - BATTERY)
a.
A456536C01
2.365,0.844 2.667,0.417 2.667,0.417 2.833,0.417 true 0.125,0.104 0.479,0.333 0.354,0.229 10 false *1 2.896,0.323 3.25,0.573 0.354,0.25 10 false *a
*1 Starter Assembly
*a D80-1 (B)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D80-1 (B) - Body ground Always 9.5 to 14 V


CAUTION:

Before performing this step, check that the starter assembly connector D80 is not disconnected or loose.



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)
a.

Remove the ST NO. 1 relay from the No. 1 engine room relay block.


b.

Disconnect the D54 starter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (ST NO. 1 relay holder) - D54-1 (ST) Always Below 1 Ω
3 (ST NO. 1 relay holder) - D55-1 (ZYV) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

12.INSPECT RELAY (ST NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT RELAY (ST NO. 1 RELAY)

OK

13.INSPECT STARTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.INSPECT STARTER ASSEMBLY

OK

REPLACE ENGINE STOP AND START ECU

Click hereEngine / Hybrid System>STOP AND START>ENGINE STOP AND START ECU>REMOVAL

HINT:

If arriving at this item from the item "Drive command is being sent from the engine stop and start ECU but the starter itself is not moving" of "After Engine Stops due to Stop and Start System, Engine does not Restart" in Stop and Start / Stop and Start System / Problem Symptoms Table, go to SIMULATION METHOD.



NG

14.CHECK HARNESS AND CONNECTOR (STA SIGNAL)
a.

Disconnect the engine stop and start ECU connectors.

A348463C43
0.917,0.667 1.333,0.917 0.417,0.25 3.25,0.5 3.667,0.75 0.417,0.25 5.75,0.531 6.167,0.781 0.417,0.25 3.813,2.219 3.646,1.917 true 2.885,2.198 2.708,1.75 true 0.323,0.115 0.635,0.313 0.313,0.198 10 false *a 1,0.708 1.469,0.896 0.469,0.188 10 false A66 3.354,0.542 3.802,0.74 0.448,0.198 10 false A67 5.833,0.573 6.333,0.833 0.5,0.26 10 false H43 3.729,2.229 4.042,2.427 0.313,0.198 10 false STA 2.74,2.229 3.208,2.438 0.469,0.208 10 false DGND
*a Front view of wire harness connector
(to Engine Stop and Start ECU)
- -



b.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition
A67-21 (STA) - A67-2 (DGND) Cranking commanded via Active Test item Starter(Hood Close) 6 to 14 V


HINT:

The Active Test "Starter" is stopped automatically 3 seconds after the starter assembly begins operating.



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE STOP AND AND START ECU - ST NO. 1 RELAY)

NG

REPLACE ENGINE STOP AND START ECU

Click hereEngine / Hybrid System>STOP AND START>ENGINE STOP AND START ECU>REMOVAL

HINT:

If arriving at this item from the item "Drive command is being sent from the engine stop and start ECU but the starter itself is not moving" of "After Engine Stops due to Stop and Start System, Engine does not Restart" in Stop and Start / Stop and Start System / Problem Symptoms Table, go to SIMULATION METHOD.



15.CHECK HARNESS AND CONNECTOR (ST RELAY - AUXILIARY BATTERY)
a.

Remove the ST relay from the NO. 1 engine room relay block and junction block assembly


b.
A456535C01
0.125,0.083 0.438,0.24 0.313,0.156 10 false *1 2.198,0.354 2.51,0.51 0.313,0.156 10 false *a
*1 No. 1 Engine Room Relay Block
*a ST NO. 1 Relay Holder


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
ST relay terminal 5 - Body ground Always 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - BATTERY)
a.
A456537C01
1.813,0.688 2.167,0.25 2.167,0.25 2.333,0.25 true 0.115,0.104 0.427,0.26 0.313,0.156 10 false *1 2.406,0.188 2.719,0.344 0.313,0.156 10 false *a
*1 Starter Assembly
*a D80-1(B)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D80-1 (B) - Body ground Always 9.5 to 14 V


CAUTION:

Before performing this step, check that the starter assembly connector D80 is not disconnected or loose.



Result:
Proceed to
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)
a.

Remove the ST NO. 1 relay from the No. 1 engine room relay block.


b.

Disconnect the D54 starter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (ST NO. 1 relay holder) - D54-1 (ST) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

18.INSPECT RELAY (ST NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.INSPECT RELAY (ST NO. 1 RELAY)

OK

19.INSPECT STARTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.INSPECT STARTER ASSEMBLY

OK

REPLACE ENGINE STOP AND START ECU

Click hereEngine / Hybrid System>STOP AND START>ENGINE STOP AND START ECU>REMOVAL

HINT:

If arriving at this item from the item "Drive command is being sent from the engine stop and start ECU but the starter itself is not moving" of "After Engine Stops due to Stop and Start System, Engine does not Restart" in Stop and Start / Stop and Start System / Problem Symptoms Table, go to SIMULATION METHOD.



NG

20.READ VALUE USING GTS (STARTER(HOOD CLOSE))
a.

Enter the following menus: Powertrain / Stop and Start / Active Test / Starter(Hood Close)

Powertrain > Stop and Start > Active Test
Tester Display
Starter(Hood Close)
50004 392 42017

b.

Check whether the engine cranks while the Active Test "Starter(Hood Close)" is being performed.

NOTICE:

The Active Test "Starter(Hood Close)" is stopped automatically 3 seconds after the starter assembly begins operating.



Standard:

Engine cranks


Result:
Result Proceed to
Engine cranks (for CVT) A
Engine cranks (for Manual transaxle) B
Engine does not crank C



A

21.READ VALUE USING GTS (NEUTRAL SWITCH)

B

29.READ VALUE USING GTS (CLUTCH LOWER SWITCH)

C

38.CHECK HARNESS AND CONNECTOR (STA SIGNAL)
21.READ VALUE USING GTS (NEUTRAL SWITCH)
a.

Enter the following menus: Powertrain / Stop and Start / Data List / Neutral Switch.

Powertrain > Stop and Start > Data List
Tester Display
Neutral Switch
50003 392 202

b.

Read the Data List when the shift lever is operated.

Powertrain > Stop and Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral Switch Park/Neutral position switch assembly status OFF / ON ON: Shift lever in P or N
OFF: Shift lever not in P or N
-

Result:
Result Proceed to
Data List display is not as specified A
Data List display is within the specification (w/ Entry and Start System) B
Data List display is within the specification (w/o Entry and Start System) C



A

22.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

B

24.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE STOP AND START ECU)

C

26.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
22.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

OK

23.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)

NG

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

23.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)
a.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


b.

Remove the ST NO. 1 relay from the No. 1 engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-10 (STAR) - 2 (ST NO. 1 relay holder) Shift lever in P or N Below 1 Ω
H45-3 (STA) - Body ground Shift lever not in P or N 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

24.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE STOP AND START ECU)
a.

Disconnect the D45 park/neutral position switch assembly connector.


b.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


c.

Disconnect the A67 engine stop and start ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-10 (STAR) - A67-17 (CLL) Always Below 1 Ω
H45-10 (STAR) - D45-4 (B) Always Below 1 Ω
H45-10 (STAR) - Body ground Always 10 kΩ or higher
A67-17 (CLL) - Body ground Always 10 kΩ or higher
D45-4 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

25.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (STAR SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

25.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (STAR SIGNAL)
a.

Disconnect A67 the engine stop and start ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A67-17 (CLL) - Body ground Engine started using push start switch assembly (engine start) 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

26.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

OK

27.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - BATTERY)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

27.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - BATTERY)
a.

Disconnect the H54 ignition or starter switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H54-4 (AM2) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

28.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

28.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the H54 ignition or starter switch assembly connector.


b.

Disconnect the D45 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H54-4 (ST2) - D45-4 (B) Always Below 1 Ω
H54-4 (ST2) - Body ground Always 10 kΩ or higher
D45-4 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

29.READ VALUE USING GTS (CLUTCH LOWER SWITCH)
Powertrain > Stop and Start > Data List
Tester Display
Clutch Lower Switch
50003 392 594
a.

Depress the clutch pedal and read the values displayed on the GTS.


Result:
Tester Display Result Proceed to
Clutch Lower Switch Fully Depressed ON
Clutch Lower Switch Fully Released OFF


Result:
Result Proceed to
OK A
NG (w/ Entry and Start System) B
NG (w/o Entry and Start System) C



A

30.INSPECT CLUTCH START SWITCH ASSEMBLY

B

33.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)

C

35.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
30.INSPECT CLUTCH START SWITCH ASSEMBLY

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION

Result:
Result Proceed to
OK (w/ Entry and Start System) A
OK (w/o Entry and Start System) B
NG C



A

31.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)

B

32.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - ST NO. 1 RELAY)

C

REPLACE CLUTCH START SWITCH ASSEMBLY

31.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)
a.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


b.

Remove the ST NO. 1 relay from the No. 1 engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-3 (STA) - 2 (ST NO. 1 relay holder) Shift lever in P or N Below 1 Ω
H45-3 (STA) - Body ground Shift lever not in P or N 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

32.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - ST NO. 1 RELAY)
a.

Disconnect the H45 ignition or starter switch assembly connector


b.

Remove the ST NO. 1 relay from the No. 1 engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-3 (STA) - 2 (ST NO. 1 relay holder) Shift lever in P or N Below 1 Ω
H45-3 (STA) - Body ground Shift lever not in P or N 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

33.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)
a.

Disconnect the A64 clutch start switch assembly connector.


b.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


c.

Disconnect the A67 engine stop and start ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-10 (STAR) - A67-17 (CLL) Always Below 1 Ω
H45-10 (STAR) - A64-2 (B) Always Below 1 Ω
H45-10 (STAR) - Body ground Always 10 kΩ or higher
A67-17 (CLL) - Body ground Always 10 kΩ or higher
A64-2 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

34.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (STAR SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

34.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (STAR SIGNAL)
a.

Disconnect A67 the engine stop and start ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A67-17 (CLL) - Body ground Engine started using push start switch assembly (engine start) 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

35.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

OK

36.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - BATTERY)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

36.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - BATTERY)
a.

Disconnect the H54 ignition or starter switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H54-1 (AM2) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

37.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

37.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY)
a.

Disconnect the H54 ignition or starter switch assembly connector.


b.

Disconnect the A64 clutch start switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H54-4 (ST2) - A64-2 (B) Always Below 1 Ω
H54-4 (ST2) - Body ground Always 10 kΩ or higher
A64-2 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

38.CHECK HARNESS AND CONNECTOR (STA SIGNAL)
a.

Disconnect the A66, A67 and H43 engine stop and start ECU connectors.

A348463C43
0.917,0.667 1.333,0.917 0.417,0.25 3.25,0.5 3.667,0.75 0.417,0.25 5.75,0.531 6.167,0.781 0.417,0.25 3.813,2.219 3.646,1.917 true 2.885,2.198 2.708,1.75 true 0.323,0.115 0.635,0.313 0.313,0.198 10 false *a 1,0.708 1.469,0.896 0.469,0.188 10 false A66 3.354,0.542 3.802,0.74 0.448,0.198 10 false A67 5.833,0.573 6.333,0.833 0.5,0.26 10 false H43 3.729,2.229 4.042,2.427 0.313,0.198 10 false STA 2.74,2.229 3.208,2.438 0.469,0.208 10 false DGND
*a Front view of wire harness connector
(to Engine Stop and Start ECU)
- -



b.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU


c.

Check the waveform immediately after starting.

Standard Resistance:
Tester Connection Condition Specified Condition
A67-21 (STA) - A67-6 (DGND) Ignition switch ON 6 to 14 V
Cranking commanded via Active Test item Starter(Hood Close)*1


*1: In the case of stop and start inspection procedure.



Result:
Result Proceed to
OK A
NG B
NG*1 C


*1: In the case of stop and start inspection procedure.



A

39.INSPECT RELAY (ST NO. 1 RELAY)

B

43.CHECK HARNESS AND CONNECTOR (POWER SUPPLY CIRCUIT)

C

IF ARRIVING AT THIS ITEM FROM CONTROL HISTORY (BATTERY VOLTAGE)", "14. INSPECT AUXILIARY BATTERY" OR "21. CHECK DATA POINTS", GO TO SIMULATION METHOD

39.INSPECT RELAY (ST NO. 1 RELAY)

OK

40.CHECK HARNESS AND CONNECTOR (POWER SUPPLY CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

40.CHECK HARNESS AND CONNECTOR (POWER SUPPLY CIRCUIT)
a.

Disconnect the A66, A67 and H43 engine stop and start ECU connectors.

A348463C34
0.948,0.51 1.313,0.75 0.365,0.24 3.396,0.5 3.76,0.74 0.365,0.24 5.792,0.521 6.198,0.771 0.406,0.25 0.365,2.073 0.719,1.563 true 0.906,2.052 0.74,1.75 true 2.438,2.094 2.604,1.708 true 5.542,2.063 5.771,1.771 true 6.354,2.052 6.198,1.771 true 0.323,0.115 0.635,0.313 0.313,0.198 10 false *a 1.031,0.563 1.344,0.76 0.313,0.198 10 false A66 3.469,0.552 3.781,0.75 0.313,0.198 10 false A67 5.875,0.573 6.375,0.833 0.5,0.26 10 false H43 0.844,2.104 1.156,2.302 0.313,0.198 10 false BIN1 0.229,2.104 0.542,2.302 0.313,0.198 10 false BIN2 2.323,2.115 2.635,2.313 0.313,0.198 10 false +B 6.292,2.083 6.604,2.281 0.313,0.198 10 false IGR 5.427,2.094 5.74,2.292 0.313,0.198 10 false IGP
*a Front view of wire harness connector
(to Engine Stop and Start ECU)
- -



b.

Measure the voltage according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Voltage:
Tester Connection Condition Specified Condition
A66-3 (BIN1) - Body ground Always 9.5 to 14 V
A66-1 (BIN2) - Body ground Always 9.5 to 14 V



c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Voltage:
Tester Connection Condition Specified Condition
A67-1 (+B) - Body ground Ignition switch ON 9.5 to 14 V
H43-18 (IGP) - Body ground Ignition switch ON 9.5 to 14 V
H43-21 (IGR) - Body ground Ignition switch ON 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

41.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

41.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)
a.

Disconnect the A66 and A67 engine stop and start ECU connectors.


b.

Measure the voltage according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition
A66-2 (GND2) - Body ground Always Below 1 Ω
A67-6 (DGND) - Body ground Always Below 1 Ω
A66-8 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

42.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

42.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST NO. 1 RELAY)
a.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.*1

*1: w/ Entry and Start System



b.

Disconnect the D45 park/neutral position switch assembly connector.*1

*1: for CVT



c.

Disconnect the A64 clutch switch assembly connector.*1

*1: for Manual Transaxle



d.

Disconnect the A54*1 or A55*2 ECM connector.

*1: for M15A-FKS

*2: for 1KR-FE



e.

Disconnect the A67 engine stop and start ECU connector.


f.

Remove the ST NO. 1 relay from the No. 1 engine room relay block.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A67-21 (STA) - 2 (ST NO. 1 relay holder) Always Below 1 Ω
A67-21 (STA) - Body ground Always 10 kΩ or higher
2 (ST NO. 1 relay holder) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE STOP AND START ECU

Click hereEngine / Hybrid System>STOP AND START>ENGINE STOP AND START ECU>REMOVAL

HINT:

If arriving at this item from the item "Drive command is being sent from the engine stop and start ECU but the starter itself is not moving" of "After Engine Stops due to Stop and Start System, Engine does not Restart" in Stop and Start / Stop and Start System / Problem Symptoms Table, go to SIMULATION METHOD.



NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

43.CHECK HARNESS AND CONNECTOR (POWER SUPPLY CIRCUIT)
a.

Disconnect the A66, A67 and H43 engine stop and start ECU connectors.

A348463C34
0.948,0.51 1.313,0.75 0.365,0.24 3.396,0.5 3.76,0.74 0.365,0.24 5.792,0.521 6.198,0.771 0.406,0.25 0.365,2.073 0.719,1.563 true 0.906,2.052 0.74,1.75 true 2.438,2.094 2.604,1.708 true 5.542,2.063 5.771,1.771 true 6.354,2.052 6.198,1.771 true 0.323,0.115 0.635,0.313 0.313,0.198 10 false *a 1.031,0.563 1.344,0.76 0.313,0.198 10 false A66 3.469,0.552 3.781,0.75 0.313,0.198 10 false A67 5.875,0.573 6.375,0.833 0.5,0.26 10 false H43 0.844,2.104 1.156,2.302 0.313,0.198 10 false BIN1 0.229,2.104 0.542,2.302 0.313,0.198 10 false BIN2 2.323,2.115 2.635,2.313 0.313,0.198 10 false +B 6.292,2.083 6.604,2.281 0.313,0.198 10 false IGR 5.427,2.094 5.74,2.292 0.313,0.198 10 false IGP
*a Front view of wire harness connector
(to Engine Stop and Start ECU)
- -



b.

Measure the voltage according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Voltage:
Tester Connection Condition Specified Condition
A66-3 (BIN1) - Body ground Always 9.5 to 14 V
A66-1 (BIN2) - Body ground Always 9.5 to 14 V



c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Voltage:
Tester Connection Condition Specified Condition
A67-1 (+B) - Body ground Ignition switch ON 9.5 to 14 V
H43-18 (IGP) - Body ground Ignition switch ON 9.5 to 14 V
H43-21 (IGR) - Body ground Ignition switch ON 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

44.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

44.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)
a.

Disconnect the A66 and A67 engine stop and start ECU connectors.


b.

Measure the voltage according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition
A66-2 (GND2) - Body ground Always Below 1 Ω
A67-6 (DGND) - Body ground Always Below 1 Ω
A66-8 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

45.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

45.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST NO. 1 RELAY)
a.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.*1

*1: w/ Entry and Start System



b.

Disconnect the D45 park/neutral position switch assembly connector.*1

*1: for CVT



c.

Disconnect the A64 clutch switch assembly connector.*1

*1: for Manual Transaxle



d.

Disconnect the A54*1 or A55*2 ECM connector.

*1: for M15A-FKS

*2: for 1KR-FE



e.

Disconnect the A67 engine stop and start ECU connector.


f.

Remove the ST NO. 1 relay from the No. 1 engine room relay block.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A67-21 (STA) - 2 (ST NO. 1 relay holder) Always Below 1 Ω
A67-21 (STA) - Body ground Always 10 kΩ or higher
2 (ST NO. 1 relay holder) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE STOP AND START ECU

Click hereEngine / Hybrid System>STOP AND START>ENGINE STOP AND START ECU>REMOVAL

HINT:

If arriving at this item from the item "Drive command is being sent from the engine stop and start ECU but the starter itself is not moving" of "After Engine Stops due to Stop and Start System, Engine does not Restart" in Stop and Start / Stop and Start System / Problem Symptoms Table, go to SIMULATION METHOD.



NG

REPAIR OR REPLACE HARNESS OR CONNECTOR