CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND POWER DISTRIBUTION BOX ASSEMBLY
| *1 | Power Distribution Box Assembly | *2 | Main Body ECU (Multiplex Network Body ECU) |
Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Connect the power distribution box assembly connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| MB-13 (GND1) - Body ground | Ground | Always | Below 1 Ω |
| MB-14 (GND2) - Body ground | Ground | Always | Below 1 Ω |
| MB-26 (BECU) - Body ground | Auxiliary battery power supply | Ignition switch off | 11 to 14 V |
| MB-27 (IGR) - Body ground | Ignition power supply | Ignition switch off | Below 1 Ω |
| Ignition switch ON | 11 to 14 V |
Install the main body ECU (multiplex network body ECU).
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>INSTALLATION
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>INSTALLATION
Connect the power distribution box assembly and main body ECU (multiplex network body ECU) connectors.
Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H4-26 (HEAD) - Body ground | Light control switch in HEAD position signal input | Light control switch not in HEAD position | 11 to 14 V |
| Light control switch in HEAD position | Below 1 V | ||
| 4D-10 - Body ground | Headlight assembly LH power supply | Ignition switch off | 11 to 14 V |
| Ignition switch ON | Below 1 V | ||
| 4D-6 - Body ground | Headlight assembly RH power supply | Ignition switch off | 11 to 14 V |
| Ignition switch ON | Below 1 V | ||
| H4-8 (CLTB) - H4-21 (CLTE) | Automatic light control sensor power supply output | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V | ||
| H4-14 (AHBI) - Body ground | Auto high beam switch signal input | Auto high beam switch on | Below 1 V |
| Auto high beam switch off | 11 to 14 V | ||
| H4-20 (CLTS) - Body ground | Automatic light control sensor signal input | Ignition switch ON | Pulse generation
(See waveform 1) |
| 4E-5 - Body ground | Front door courtesy light switch assembly RH input | Front door RH open | 4.7 to 5.3 V |
| Front door RH closed | Below 1 V |
Waveform 1
| Item | Content |
|---|---|
| Tester Connection | H4-20 (CLTS) - Body ground |
| Tool setting | 2 V/DIV., 10 ms./DIV. |
| Condition | Ignition switch ON |
The communication waveform changes according to the surrounding brightness.
CHECK COMBINATION METER ASSEMBLY
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU
CHECK HYBRID VEHICLE CONTROL ECU
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>TERMINALS OF ECU
CHECK STEERING SENSOR
for HV Model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>TERMINALS OF ECU
for Gasoline Model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>TERMINALS OF ECU
CHECK FORWARD RECOGNITION CAMERA (w/ Toyota Safety Sense)
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA SYSTEM>TERMINALS OF ECU
SEMICONDUCTOR POWER INTEGRATION ECU
Click herePower Source / Network>POWER DISTRIBUTION>POWER INTEGRATION SYSTEM>TERMINALS OF ECU