After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
This section describes the standard values for all CAN related components.
The systems (ECUs and sensors) that use CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed to the vehicle.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM
Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
NO. 1 GLOBAL CAN JUNCTION CONNECTOR
Check the No. 1 global CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 1 Global CAN Junction Connector) |
- | - |
Check the connection diagram of the components which are connected to the No. 1 global CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| H110-1 (CANH) | LG | Power steering ECU assembly
(for Bus 4) |
| H110-12 (CANL) | W | |
| H110-2 (CANH) | SB | Steering sensor
(for Bus 4) |
| H110-13 (CANL) | W | |
| H110-4 (CANH) | BR | No. 2 global CAN junction connector
(for Bus 4) |
| H110-15 (CANL) | W |
NO. 2 GLOBAL CAN JUNCTION CONNECTOR
Check the No. 2 global CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 2 Global CAN Junction Connector) |
- | - |
Check the connection diagram of the components which are connected to the No. 2 global CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| H112-1 (CANH) | B | Air bag sensor assembly
(for Bus 4) |
| H112-7 (CANL) | W | |
| H112-2 (CANH) | V | Central gateway ECU (network gateway ECU)
(for Bus 4) |
| H112-8 (CANL) | W | |
| H112-3 (CANH) | G | Brake actuator assembly
(for Bus 4) |
| H112-9 (CANL) | W | |
| H112-4 (CANH) | BR | No. 1 global CAN junction connector
(for Bus 4) |
| H112-10 (CANL) | W |
NO. 3 GLOBAL CAN JUNCTION CONNECTOR
Check the No. 3 global CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 3 Global CAN Junction Connector) |
- | - |
Check the connection diagram of the components which are connected to the No. 3 global CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| H114-1 (CANH) | B | Central gateway ECU (network gateway ECU)
(for Bus 5) |
| H114-12 (CANL) | W | |
| H114-2 (CANH) | SB | Main body ECU (multiplex network body ECU)
(for Bus 5) |
| H114-13 (CANL) | W | |
| H114-3 (CANH) | R | Air conditioning amplifier assembly
(for Bus 5) |
| H114-14 (CANL) | W | |
| H114-4 (CANH) | L | Certification ECU (smart key ECU assembly)
(for Bus 5) |
| H114-15 (CANL) | W |
NO. 4 GLOBAL CAN JUNCTION CONNECTOR
Check the No. 4 global CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 4 Global CAN Junction Connector) |
- | - |
Check the connection diagram of the components which are connected to the No. 4 global CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| H115-1 (CANH) | R | Central gateway ECU (network gateway ECU)
(for Bus 3) |
| H115-12 (CANL) | W | |
| H115-2 (CANH) | BR | Combination meter assembly
(for Bus 3) |
| H115-13 (CANL) | W | |
| H115-3 (CANH) | LG | Radio and display receiver assembly
(for Bus 3) |
| H115-14 (CANL) | W | |
| H115-4 (CANH) | BE | Telematics transceiver
(for Bus 3) |
| H115-15 (CANL) | W | |
| H115-5 (CANH) | SB | Meter mirror sub-assembly
(for Bus 3) |
| H115-16 (CANL) | W |
NO. 6 GLOBAL CAN JUNCTION CONNECTOR
Check the No. 6 global CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 6 Global CAN Junction Connector) |
- | - |
Check the connection diagram of the components which are connected to the No. 5 global CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| H117-1 (CANH) | Y | ECM
(for Bus 2) |
| H117-12 (CANL) | W | |
| H117-2 (CANH) | BR | Engine stop and start ECU*1
(for Bus 2) |
| H117-13 (CANL) | W | |
| H117-3 (CANH) | LG | Central gateway ECU (network gateway ECU)
(for Bus 2) |
| H117-14 (CANL) | W | |
| H117-4 (CANH) | L | TCM
(for Bus 2) |
| H117-15 (CANL) | W | |
| H117-9 (CANH) | B | Brake actuator assembly
(for Chassis Local Bus) |
| H117-20 (CANL) | W | |
| H117-10 (CANH) | R | Engine stop and start ECU*1
(for Chassis Local Bus) |
| H117-21 (CANL) | W | |
| H117-11 (CANH) | V | Central gateway ECU (network gateway ECU)
(for Chassis Local Bus) |
| H117-22 (CANL) | W |
NO. 7 GLOBAL CAN JUNCTION CONNECTOR
Check the No. 7 global CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 7 Global CAN Junction Connector) |
- | - |
Check the connection diagram of the components which are connected to the No. 7 global CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| H118-1 (CANH) | R | Forward recognition camera
(for Bus 1) |
| H118-12 (CANL) | W | |
| H118-2 (CANH) | SB | Central gateway ECU (network gateway ECU)
(for Bus 1) |
| H118-13 (CANL) | W | |
| H118-3 (CANH) | L | Millimeter wave radar sensor assembly
(for Bus 1) |
| H118-14 (CANL) | W | |
| H118-4 (CANH) | V | No. 8 global CAN junction connector
(for Bus 1) |
| H118-15 (CANL) | W |
NO. 8 GLOBAL CAN JUNCTION CONNECTOR
Check the No. 8 global CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 8 Global CAN Junction Connector) |
- | - |
Check the connection diagram of the components which are connected to the No. 8 global CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| O85-1 (CANH) | BE | Clearance warning ECU assembly
(for Bus 1) |
| O85-12 (CANL) | W | |
| O85-2 (CANH) | V | No. 7 global CAN junction connector
(for Bus 1) |
| O85-13 (CANL) | W | |
| O85-3 (CANH) | GR | Blind spot monitor sensor LH
(for Bus 1) |
| O85-14 (CANL) | W | |
| O85-4 (CANH) | LG | Rear television camera assembly
(for Bus 1) |
| O85-15 (CANL) | W | |
| O85-5 (CANH) | R | No. 1 CAN junction terminal
(for Bus 1) |
| O85-16 (CANL) | W |
NO. 9 GLOBAL CAN JUNCTION CONNECTOR
Check the No. 9 global CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 9 Global CAN Junction Connector) |
- | - |
Check the connection diagram of the components which are connected to the No. 9 global CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| O87-1 (CANH) | G | Central gateway ECU (network gateway ECU)
(for Bus 6) |
| O87-12 (CANL) | W | |
| O87-2 (CANH) | L | Central gateway ECU (network gateway ECU)
(for Bus 6) |
| O87-13 (CANL) | W | |
| O87-4 (CANH) | R | Tire pressure warning ECU and receiver
(for Bus 6) |
| O87-15 (CANL) | W |
NO. 1 CAN JUNCTION TERMINAL
Check the No. 1 CAN junction terminal.
| *a | Rear view of wire harness connector
(to No. 1 CAN Junction Terminal) |
Connection diagram
Check the connection diagram of the components which are connected to the No. 1 CAN junction terminal.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| O86-3 (CANH) | R | No. 8 global CAN junction connector
(for Bus 1) |
| O86-2 (CANL) | W |
DLC3
Disconnect the cable from the negative (-) auxiliary battery terminal.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H3-6 (CANH) - H3-14 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| H3-6 (CANH) - H3-4 (CG) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H3-14 (CANL) - H3-4 (CG) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H3-6 (CANH) - H3-16 (BAT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H3-14 (CANL) - H3-16 (BAT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)
| *a | Component without harness connected
(Central Gateway ECU (Network Gateway ECU)) |
- | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H40 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU)) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H40-16 (CA6H) - H40-17 (CA6L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 1 MΩ or higher |
| H40-16 (CA6H) - H40-22 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H40-17 (CA6L) - H40-22 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H40-16 (CA6H) - H40-1 (BATT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H40-17 (CA6L) - H40-1 (BATT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H40-28 (CA1H) - H40-27 (CA1L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| H40-28 (CA1H) - H40-22 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H40-27 (CA1L) - H40-22 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H40-28 (CA1H) - H40-1 (BATT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H40-27 (CA1L) - H40-1 (BATT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H40-26 (CA4H) - H40-25 (CA4L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| H40-26 (CA4H) - H40-22 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H40-25 (CA4L) - H40-22 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H40-26 (CA4H) - H40-1 (BATT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H40-25 (CA4L) - H40-1 (BATT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H40-30 (CA3H) - H40-29 (CA3L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| H40-30 (CA3H) - H40-22 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H40-29 (CA3L) - H40-22 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H40-30 (CA3H) - H40-1 (BATT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H40-29 (CA3L) - H40-1 (BATT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H40-24 (CA2H) - H40-23 (CA2L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| H40-24 (CA2H) - H40-22 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H40-23 (CA2L) - H40-22 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H40-24 (CA2H) - H40-1 (BATT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H40-23 (CA2L) - H40-1 (BATT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H40-7 (CA5H) - H40-8 (CA5L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| H40-7 (CA5H) - H40-22 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H40-8 (CA5L) - H40-22 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H40-7 (CA5H) - H40-1 (BATT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H40-8 (CA5L) - H40-1 (BATT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H40-31 (CA7H) - H40-10 (CAVH) | HIGH-level CAN bus line - HIGH-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | Below 1 Ω |
| H40-32 (CA7L) - H40-11 (CAVL) | LOW-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | Below 1 Ω |
| H40-31 (CA7H) - H40-22 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H40-32 (CA7L) - H40-22 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H40-31 (CA7H) - H40-1 (BATT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H40-32 (CA7L) - H40-1 (BATT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H40-5 (CA8H) - H40-6 (CA8L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| H40-5 (CA8H) - H40-22 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H40-6 (CA8L) - H40-22 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H40-5 (CA8H) - H40-1 (BATT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H40-6 (CA8L) - H40-1 (BATT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H40-12 (CAWH) - H40-13 (CAWL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| H40-12 (CAWH) - H40-22 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H40-13 (CAWL) - H40-22 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H40-12 (CAWH) - H40-1 (BATT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H40-13 (CAWL) - H40-1 (BATT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
ECM (for M15A-FKS)
Refer to Terminals of ECU.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>TERMINALS OF ECM
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the A54 ECM connector.
| *a | Front view of wire harness connector
(to ECM) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A54-8 (CANH) - A54-18 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| A54-8 (CANH) - A54-10 (E1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A54-18 (CANL) - A54-10 (E1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A54-8 (CANH) - A54-1 (BATT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A54-18 (CANL) - A54-1 (BATT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
ECM (for 1KR-FE)
Refer to Terminals of ECU.
Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>TERMINALS OF ECM
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the A55 ECM connector.
| *a | Front view of wire harness connector
(to ECM) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A55-26 (CANH) - A55-25 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| A55-26 (CANH) - A55-4 (E1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A55-25 (CANL) - A55-4 (E1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A55-26 (CANH) - A55-15 (BATT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A55-25 (CANL) - A55-15 (BATT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
TCM (for CVT)
Refer to Terminals of ECU.
Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the D71 TCM connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to TCM) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| D71-15 (CANH) - D71-16 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| D71-15 (CANH) - D71-2 (E1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| D71-16 (CANL) - D71-2 (E1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| D71-15 (CANH) - H3-16 (BAT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| D71-16 (CANL) - H3-16 (BAT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)
Refer to Terminals of ECU.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H80 radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Radio and Display Receiver Assembly) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H80-13 (CANH) - H80-14 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| H80-13 (CANH) - H3-4 (CG) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H80-14 (CANL) - H3-4 (CG) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H80-13 (CANH) - H3-16 (BAT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H80-14 (CANL) - H3-16 (BAT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
BRAKE ACTUATOR ASSEMBLY (for TMC Made)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the A36 brake actuator assembly connector.
| *a | Front view of wire harness connector
(to Brake Actuator Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A36-22 (CANH) - A36-10 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A36-22 (CANH) - A36-25 (GND1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A36-10 (CANL) - A36-25 (GND1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A36-22 (CANH) - A36-38 (+BS) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A36-10 (CANL) - A36-38 (+BS) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
BRAKE ACTUATOR ASSEMBLY (for TMMF Made)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the A37 brake actuator assembly connector.
| *a | Front view of wire harness connector
(to Brake Actuator Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A37-11 (CANH) - A37-10 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A37-11 (CANH) - A37-38 (GND1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A37-10 (CANL) - A37-38 (GND1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A37-11 (CANH) - A37-25 (+BS) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A37-10 (CANL) - A37-25 (+BS) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A37-19 (CA2H) - A37-18 (CA2L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| A37-19 (CA2H) - A37-38 (GND1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A37-18 (CA2L) - A37-38 (GND1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A37-19 (CA2H) - A37-25 (+BS) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A37-18 (CA2L) - A37-25 (+BS) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
STEERING SENSOR
| *a | Component without harness connected
(Steering Sensor) |
- | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H39 steering sensor connector.
| *a | Front view of wire harness connector
(to Steering Sensor) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H39-3 (CANH) - H39-8 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| H39-3 (CANH) - H39-6 (ESS) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H39-8 (CANL) - H39-6 (ESS) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H39-3 (CANH) - H39-4 (BATT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H39-8 (CANL) - H39-4 (BATT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
POWER STEERING ECU ASSEMBLY
Refer to Terminals of ECU.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H1 and H2 power steering ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to Power Steering ECU Assembly) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H1-7 (CANH) - H1-8 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| H1-7 (CANH) - H2-2 (PGND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H1-8 (CANL) - H2-2 (PGND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H1-7 (CANH) - H2-1 (PIG) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H1-8 (CANL) - H2-1 (PIG) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
AIRBAG SENSOR ASSEMBLY
Refer to Terminals of ECU.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H14 airbag sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Airbag Sensor Assembly) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H14-26 (CAFH) - H14-27 (CAFL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| H14-26 (CAFH) - H14-33 (E1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H14-27 (CAFL) - H14-33 (E1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H14-26 (CAFH) - H3-16 (BAT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H14-27 (CAFL) - H3-16 (BAT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Entry and Start System)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H46 certification ECU (smart key ECU assembly) connector.
| *a | Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H46-1 (CANH) - H46-2 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| H46-1 (CANH) - H46-29 (E) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H46-2 (CANL) - H46-29 (E) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H46-1 (CANH) - H46-6 (+B) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H46-2 (CANL) - H46-6 (+B) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
METER MIRROR SUB-ASSEMBLY (w/ Headup Display System)
Refer to Terminals of ECU.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>HEADUP DISPLAY SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H61 meter mirror sub-assembly connector.
| *a | Front view of wire harness connector
(to Meter Mirror Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H61-12 (MPX1) - H61-13 (MPX2) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| H61-12 (MPX1) - H61-4 (ES) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H61-13 (MPX2) - H61-4 (ES) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H61-12 (MPX1) - H61-2 (B) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H61-13 (MPX2) - H61-2 (B) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
AIR CONDITIONING AMPLIFIER ASSEMBLY (for Automatic Air Conditioning System)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H24 air conditioning amplifier assembly connector.
| *a | Front view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H24-2 (CANH) - H24-1 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| H24-2 (CANH) - H24-17 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H24-1 (CANL) - H24-17 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H24-2 (CANH) - H24-5 (B) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H24-1 (CANL) - H24-5 (B) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
AIR CONDITIONING AMPLIFIER ASSEMBLY (for Manual Air Conditioning System)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H23 air conditioning amplifier assembly connector.
| *a | Front view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H23-9 (CANH) - H23-26 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| H23-9 (CANH) - H23-27 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H23-26 (CANL) - H23-27 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H23-9 (CANH) - H23-1 (B) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H23-26 (CANL) - H23-1 (B) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
Refer to Terminals of ECU.
Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H4 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU)) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H4-2 (CANH) - H4-1 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| H4-2 (CANH) - H3-4 (CG) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H4-1 (CANL) - H3-4 (CG) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H4-2 (CANH) - H3-16 (BAT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H4-1 (CANL) - H3-16 (BAT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
COMBINATION METER ASSEMBLY
Refer to Terminals of ECU.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H6 combination meter assembly connector.
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H6-9 (CANH) - H6-25 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| H6-9 (CANH) - H6-23 (ES) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H6-25 (CANL) - H6-23 (ES) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H6-9 (CANH) - H6-22 (B) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H6-25 (CANL) - H6-22 (B) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
CLEARANCE WARNING ECU ASSEMBLY (w/ TOYOTA Parking Assist-sensor System)
Refer to Terminals of ECU.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the O60 clearance warning ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Clearance Warning ECU Assembly) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| O60-17 (R1) - O60-18 (R2) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| O60-17 (R1) - O60-31 (E) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| O60-18 (R2) - O60-31 (E) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| O60-17 (R1) - H3-16 (BAT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| O60-18 (R2) - H3-16 (BAT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
FORWARD RECOGNITION CAMERA (w/ Toyota Safety Sense)
Refer to Terminals of ECU.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the V10 forward recognition camera connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Forward Recognition Camera) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| V10-5 (CA1P) - V10-11 (CA1N) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| V10-5 (CA1P) - V10-10 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| V10-11 (CA1N) - V10-10 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| V10-5 (CA1P) - H3-16 (BAT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| V10-11 (CA1N) - H3-16 (BAT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Toyota Safety Sense)
Refer to Terminals of ECU.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT RADAR SENSOR SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the B8 millimeter wave radar sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| B8-3 (CA2H) - B8-2 (CA2L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| B8-3 (CA2H) - B8-1 (SGND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| B8-2 (CA2L) - B8-1 (SGND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| B8-3 (CA2H) - H3-16 (BAT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| B8-2 (CA2L) - H3-16 (BAT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
BLIND SPOT MONITOR SENSOR LH (w/ Blind Spot Monitor System)
Refer to Terminals of ECU.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the T6*1 or O38*2 blind spot monitor sensor LH connector.
*1: for TMC Made
*2: for TMMF Made
Measure the resistance according to the value(s) in the table below.
| *A | for TMC Made | *B | for TMMF Made |
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor LH) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| T6-2 (CA1P) - T6-7 (CA1N) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| T6-2 (CA1P) - T6-10 (BLGD) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| T6-7 (CA1N) - T6-10 (BLGD) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| T6-2 (CA1P) - H3-16 (BAT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| T6-7 (CA1N) - H3-16 (BAT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| O38-2 (CA1P) - O38-7 (CA1N) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| O38-2 (CA1P) - O38-10 (BLGD) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| O38-7 (CA1N) - O38-10 (BLGD) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| O38-2 (CA1P) - H3-16 (BAT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| O38-7 (CA1N) - H3-16 (BAT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
REAR TELEVISION CAMERA ASSEMBLY (w/ Parking Assist Monitor System)
Refer to Terminals of ECU.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the Y2 rear television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Rear Television Camera Assembly) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| Y2-4 (CANH) - Y2-1 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| Y2-4 (CANH) - H3-4 (CG) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| Y2-1 (CANL) - H3-4 (CG) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| Y2-4 (CANH) - H3-16 (BAT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Y2-1 (CANL) - H3-16 (BAT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
TIRE PRESSURE WARNING ECU AND RECEIVER (w/ Tire Pressure Warning System)
Refer to Terminals of ECU.
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the O33*1 or O34*2 tire pressure warning ECU and receiver connector.
*1: w/o Entry and Start System
*2: w/ Entry and Start System
| *A | w/o Entry and Start System |
| *B | w/ Entry and Start System |
| *a | Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| O33-9 (CANH) - O33-10 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| O33-9 (CANH) - O33-12 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| O33-10 (CANL) - O33-12 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| O33-9 (CANH) - O33-7 (+B) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| O33-10 (CANL) - O33-7 (+B) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| O34-9 (CANH) - O34-10 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| O34-9 (CANH) - O34-12 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| O34-10 (CANL) - O34-12 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| O34-9 (CANH) - O34-7 (+B) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| O34-10 (CANL) - O34-7 (+B) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
TELEPHONE TRANSCEIVER ASSEMBLY (w/ Telematics Transceiver)
Refer to Terminals of ECU.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H85 telephone transceiver assembly connector.
| *a | Front view of wire harness connector
(to Telephone Transceiver Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H85-25 (CANP) - H85-26 (CANN) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| H85-25 (CANP) - H85-20 (E) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H85-26 (CANN) - H85-20 (E) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H85-25 (CANP) - H85-1 (+B) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H85-26 (CANN) - H85-1 (+B) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
ENGINE STOP AND START ECU (w/ Stop and Start System)
Refer to Terminals of ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H43 engine stop and start ECU connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Engine Stop and Start ECU) |
- | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H43-13 (CANH) - H43-14 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| H43-13 (CANH) - H3-4 (CG) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H43-14 (CANL) - H3-4 (CG) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H43-13 (CANH) - H3-16 (BAT) | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H43-14 (CANL) - H3-16 (BAT) | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |