Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › FRAME WIRE › 2020.07–2021.11
RM36W0E _51 Engine / Hybrid System _087936 HYBRID / BATTERY CONTROL _0424590 FRAME WIRE A

HYBRID / BATTERY CONTROL  FRAME WIRE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during HV floor under wire removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Front wheel alignment adjustment
1.

Perform "Reset Memory"

2.

Perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for TMC Made:
(Click here)
for TMMF Made:
(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



HINT:
·

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 6.TEMPORARILY INSTALL CONNECTOR COVER ASSEMBLY

Hide 73350C 8.DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY

Hide 9.REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Hide 72693 10.REMOVE REAR SEAT CUSHION LOCK HOOK

Hide 76971G 11.REMOVE REAR UNDER COVER

Hide 71033 12.REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY

Hide G9230 13.REMOVE BATTERY COOLING BLOWER ASSEMBLY

Hide G92N1 14.REMOVE HV BATTERY UPPER COVER PANEL

Hide 821H1 15.DISCONNECT FLOOR UNDER WIRE

CAUTION:

Wear insulated gloves.


a.
A466092C01
1.927,0.667 2.26,0.667 true 2.26,0.531 2.469,0.729 0.208,0.198 10 true *a
*a Shield Ground


Disconnect the 2 HV battery junction block assembly connectors.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



b.

Disconnect the shield ground from the HV battery.


c.

Disconnect the floor wire connector.


Hide 57628E 16.REMOVE REAR FLOOR SIDE MEMBER COVER LH (w/ Cover)

a.
A464168

Remove the 2 bolts.


b.

Disengage the grommet to remove the rear floor side member cover LH.


Hide 64740C 17.REMOVE FRONT FLOOR COVER LH (w/ Cover)

a.
A464169

Remove the 2 bolts, 2 clips and disengage the 6 clamps to remove the front floor cover LH from the vehicle body.


Hide 51201 18.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 821H1 19.REMOVE FLOOR UNDER WIRE

CAUTION:

Wear insulated gloves.


NOTICE:

Insulate the disconnected connectors with insulating tape.


a.
A464170

Remove the 2 nuts.


b.

Remove the 3 nuts and clamp.

A458351

NOTICE:

If the clamps are removed forcibly, the stud bolts may be damaged.



c.
A464173

Disengage the grommet and pull out the HV floor under wire from the floor panel hole.


d.
A464171

Disengage the 4 clamps.


e.

Disconnect the HV floor under wire connector.


f.

Remove the bolt, nut and HV floor under wire.