Home › Drivetrain › EC6E (MANUAL TRANSMISSION / TRANSAXLE) › TRANSMISSION CONTROL CABLE (for TMMF Made) › from 2020.07
RM36W0E _52 Drivetrain _089427 EC6E MANUAL TRANSMISSION / TRANSAXLE _0432165 TRANSMISSION CONTROL CABLE(for TMMF Made) N

EC6E MANUAL TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE(for TMMF Made)  ADJUSTMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transmission control cable assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Parking support brake system (Click here)
·

Air intake system parts

·

Exhaust system parts


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1.SECURE VEHICLE

a.

Fully apply the parking brake and chock a wheel.

CAUTION:
·
C332327

Make sure to apply the parking brake and chock a wheel before performing this procedure.

·

If the vehicle is not secure and the shift lever is moved to neutral, the vehicle may suddenly move, possibly resulting in an accident or serious injury.




Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 4.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17701 5.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 74404A 7.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 58910C 8.REMOVE CONSOLE BOX ASSEMBLY REAR

Hide 33820B 9.ADJUST TRANSMISSION CONTROL CABLE ASSEMBLY

HINT:
·

After the floor shift shift lever assembly or the transmission control cable assembly is replaced, be sure to adjust the transmission control cable assembly.

·

If the shift lever does not move (or the shift lever is difficult to move) to the 1st or 2nd position, or if it is possible to move the shift lever to the reverse position without pulling up the slider shaft, the length of the transmission control cable assembly must be adjusted.



a.
C434070

Remove the clip and disconnect the transmission control select cable from the floor shift shift lever assembly.


b.
C272829C05
0.052,0.073 3.365,2.135 3.313,2.063 0.073,2.583 3.365,4.469 3.292,1.885 1.094,0.917 1.25,0.635 1.25,0.635 1.417,0.635 false 1.448,1.844 1.448,1.583 false 0.521,1.865 0.521,1.604 false 0.521,4.135 0.521,3.875 false 1.469,4.115 1.469,3.854 false 2.698,0.438 3.01,0.594 0.313,0.156 10 false *a 0.458,1.875 0.771,2.031 0.313,0.156 10 false *e 1.385,1.875 1.698,2.031 0.313,0.156 10 false *f 1.469,0.552 1.781,0.708 0.313,0.156 10 false *d 0.635,0.583 0.948,0.74 0.313,0.156 10 false *b 2.615,2.74 2.927,2.896 0.313,0.156 10 false *c 1.438,4.177 1.75,4.333 0.313,0.156 10 false *f 0.458,4.177 0.771,4.333 0.313,0.156 10 false *e
*a Twist the stopper
*b Pull
*c Return the stopper
*d Lock Piece
*e Stopper
*f Adjuster Case


Release the lock of the transmission control select cable length adjustment structure.

i.

Twist the stopper.


ii.

Pull the lock piece outward from the adjuster case to release the lock.


iii.

Return the stopper.



c.
C434070

Connect the transmission control select cable to the floor shift shift lever assembly and install the clip.

NOTICE:
·

Make sure that the lock piece of the transmission control select cable length adjustment structure is facing upward when the transmission control select cable is connected.

·

Make sure that the transmission control select cable is securely installed.




d.
C432096C02
1.677,1.417 2.01,1.958 true 1.781,0.698 2.042,0.427 true 0.938,2.875 1.385,3.375 true 2.052,1.917 2.25,2.094 0.198,0.177 10 true *1 2.073,0.323 2.281,0.51 0.208,0.188 10 true *2 0.719,2.781 1.031,2.938 0.313,0.156 10 true *a
*1 Outer Select Lever
*2 Reverse Restrict Pin Assembly
*a Secured


Hook the outer select lever of the manual transaxle assembly to the reverse restrict pin assembly to secure it.


e.
C434074C01
0.646,2.167 0.781,2.313 true 0.5,2.417 0.635,2.594 true 0.479,2 0.646,2.177 0.167,0.177 10 true *a 0.323,2.219 0.51,2.396 0.188,0.177 10 true *b
*a Slider Shaft
*b Cam Wall


Push the slider shaft against the cam wall.

NOTICE:
·

Do not pull up the slider shaft.

·

When adjusting the transmission control select cable, make sure that the shift lever is not in 1st or 2nd.




f.

Lock the transmission control select cable length adjustment structure.

i.

Twist the stopper.

C434075C02
1.438,0.552 1.667,0.333 false 0.833,1.781 0.583,1.417 0.583,1.417 0.833,1.115 false 2,2.052 2.25,1.417 2.25,1.417 2,1.104 false 1.74,0.229 2.052,0.385 0.313,0.156 10 false *d 0.385,1.323 0.698,1.479 0.313,0.156 10 false *e 2.313,1.323 2.625,1.479 0.313,0.156 10 false *f 2.688,0.177 3,0.333 0.313,0.156 10 false *a 0.99,0.25 1.302,0.406 0.313,0.156 10 false *b 2.688,1.542 3,1.698 0.313,0.156 10 false *c
*a Twist the stopper *b Push
*c Return the stopper *d Lock Piece
*e Stopper *f Adjuster Case



ii.

Push the lock piece into the adjuster case with slider shaft held against the cam wall.

NOTICE:
·

Securely press in the lock piece until the lock engages.

·

When adjusting the transmission control select cable, make sure that the shift lever is not in 1st or 2nd.




iii.

Return the stopper to prevent the lock from being released.

NOTICE:
·

Push the lock piece as far as it will go.

·

Confirm whether the transmission control select cable length adjustment structure is locked securely.





g.
C432098C02
1.135,1.417 1.469,1.344 true 1.698,0.396 1.708,0.906 true 0.927,1.313 1.125,1.479 0.198,0.167 10 true *1 1.542,0.313 1.854,0.469 0.313,0.156 10 false *2 0.927,3.438 1.104,3.625 0.177,0.188 10 true *a
*1 Outer Select Lever
*2 Reverse Restrict Pin Assembly
*a Released


Move the shift lever to the reverse position, so that the outer select lever can be released.


Hide 58910C 10.INSTALL CONSOLE BOX ASSEMBLY REAR

Hide 74404A 11.INSTALL BATTERY CLAMP SUB-ASSEMBLY

Hide 17701 13.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 14.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 15.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 16. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART