Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › 2020.07–2020.09
RM36W0E _51 Engine / Hybrid System _090986 STOP AND START _0432127 STOP AND START SYSTEM C

STOP AND START  STOP AND START SYSTEM  P253014  Ignition Switch Circuit Short to Ground or Open  


DESCRIPTION

If the engine stop and start ECU receives the off signal from the ignition or starter switch assembly*1 or certification ECU (smart key ECU assembly)*2 when communication with the ECM is normal, the engine stop and start ECU will output DTC P253014.

*1: w/o Entry and Start System

*2: w/ Entry and Start System


DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory Note
P253014 Ignition Switch Circuit Short to Ground or Open All of the following conditions are met for 10 seconds or more (1 trip detection logic):
·

Ignition switch off signal is input.

·

Communication with the ECM is normal.

·

Ignition switch (communication) ON


·

Wire harness or connector

·

EFI-MAIN NO. 1 relay

·

IGP relay

·

Power distribution box assembly (IGR-NO. 1 relay)*1

·

Ignition or starter switch assembly*2

·

Certification ECU (Smart key ECU assembly)*1

·

Engine stop and start ECU


Blinks DTC stored SAE Code: P2531

*1: w/ Entry and Start System

*2: w/o Entry and Start System


CONFIRMATION DRIVING PATTERN

CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the auxiliary battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item "Status of Battery Charge Control" changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the auxiliary battery fluid temperature at 11°C (52°F) or higher, the refresh charge will be completed.)

·

If the GTS is not available and the Data List item "Status of Battery Charge Control" cannot be checked, charge the auxiliary battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.

·

Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.



a.

for CVT

i.

Clear the DTCs.

Powertrain > Stop and Start > Clear DTCs
50002 392

ii.

Start the engine and warm it up.


iii.

Drive the vehicle at 7 km/h (4 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



iv.

Depress the brake pedal and stop the vehicle.


v.

Keep the engine stopped by stop and start control for 1 second or more. (Keep the shift lever in D.)


vi.

Release the brake pedal with the shift lever in D to start the engine.

HINT:

If the engine cranks slowly when the engine is restarted, it can be determined that the auxiliary battery voltage is low.



vii.

Check that DTCs are not output.

Powertrain > Stop and Start > Trouble Codes
50001 392


b.

for Manual Transaxle

i.

Clear the DTCs.

Powertrain > Stop and Start > Clear DTCs
50002 392

ii.

Start the engine and warm it up.


iii.

Drive the vehicle at 7 km/h (4 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



iv.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


v.

Keep the engine stopped by stop and start control for 1 second or more.


vi.

Depress the clutch pedal and start the engine.

HINT:

If the engine cranks slowly when the engine is restarted, it can be determined that the auxiliary battery voltage is low.



vii.

Check that DTCs are not output.

Powertrain > Stop and Start > Trouble Codes
50001 392



STOP AND START SYSTEM OPERATION CHECK


Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>OPERATION CHECK


WIRING DIAGRAM

for M15A-FKS


A490640E01
5.906,0.375 6.365,0.573 0.458,0.198 10 false A67 6.281,0.365 6.74,0.563 0.458,0.198 10 false +B 5.969,0.198 6.427,0.396 0.458,0.198 10 false 1 4.865,0.552 5.573,0.802 0.708,0.25 10 false EFI NO. 3 3.094,1.125 4.24,1.354 1.146,0.229 10 false EFI-MAIN NO. 1 1.01,0.958 2.156,1.188 1.146,0.229 10 false EFI-MAIN NO. 1 0.146,0.094 2.698,0.438 2.552,0.344 12 false w/ Entry and Start System: 4.083,0.688 4.542,0.885 0.458,0.198 10 false 1 4.094,0.26 4.552,0.458 0.458,0.198 10 false 3 2.969,0.688 3.427,0.885 0.458,0.198 10 false 2 2.958,0.271 3.417,0.469 0.458,0.198 10 false 5 4.448,1.698 5.156,1.948 0.708,0.25 10 false INJ 2.323,1.531 2.781,1.729 0.458,0.198 10 false A54 2.323,1.948 2.781,2.146 0.458,0.198 10 false A54 2.354,1.76 2.813,1.958 0.458,0.198 10 false 13 2.385,1.365 2.844,1.563 0.458,0.198 10 false 2 1.969,1.542 2.427,1.74 0.458,0.198 10 false IGP 1.979,1.927 2.438,2.125 0.458,0.198 10 false IGR 1.552,2.271 2.01,2.469 0.458,0.198 10 false ECM 5.906,3.708 6.365,3.906 0.458,0.198 10 false H43 5.958,3.531 6.417,3.729 0.458,0.198 10 false 21 6.271,3.698 6.729,3.896 0.458,0.198 10 false IGR 6.26,5.167 6.719,5.365 0.458,0.198 10 false IGP 6.26,5.594 6.719,5.792 0.458,0.198 10 false DGND 6.063,5.917 7.104,6.677 1.042,0.76 10 false Engine Stop and Start ECU 5.917,5.167 6.375,5.365 0.458,0.198 10 false H43 5.906,5.604 6.365,5.802 0.458,0.198 10 false A67 5.948,4.979 6.406,5.177 0.458,0.198 10 false 18 5.979,5.427 6.438,5.625 0.458,0.198 10 false 6 4.688,5.354 5.833,5.583 1.146,0.229 10 false ECU-IGP NO. 3 3.417,4.427 6.302,4.771 2.885,0.344 10 false Power Distribution Box Assembly 4.042,3.031 5.188,3.26 1.146,0.229 10 false ECU-IGR NO. 1 4,3.875 5.146,4.104 1.146,0.229 10 false ECU-IGR NO. 4 5.167,2.844 5.625,3.042 0.458,0.198 10 false 4D 5.167,2.677 5.625,2.875 0.458,0.198 10 false 22 5.167,3.708 5.625,3.906 0.458,0.198 10 false 4B 5.156,3.521 5.615,3.719 0.458,0.198 10 false 10 2.823,3.594 3.969,3.823 1.146,0.229 10 false IGR-NO. 1 2.281,4.375 2.74,4.573 0.458,0.198 10 false 4C 1.99,4.375 2.448,4.573 0.458,0.198 10 false 17 0.833,3.344 1.292,3.542 0.458,0.198 10 false 4B 0.875,3.135 1.333,3.333 0.458,0.198 10 false 9 1.417,3.49 1.875,3.688 0.458,0.198 10 false AM2 3.271,5.063 3.729,5.26 0.458,0.198 10 false 3 4.125,5.063 4.583,5.26 0.458,0.198 10 false 5 4.125,5.479 4.583,5.677 0.458,0.198 10 false 2 3.271,5.49 3.729,5.688 0.458,0.198 10 false 1 3.635,5.948 4.094,6.146 0.458,0.198 10 false IGP 3.094,7.677 5.979,8.021 2.885,0.344 10 false Certification ECU (Smart Key ECU Assembly) 3.313,6.5 3.771,6.698 0.458,0.198 10 false IGPD 3.302,6.927 3.76,7.125 0.458,0.198 10 false IGRD 3.323,7.333 3.781,7.531 0.458,0.198 10 false +B 2.938,6.5 3.396,6.698 0.458,0.198 10 false H45 2.938,6.927 3.396,7.125 0.458,0.198 10 false H45 2.927,7.302 3.385,7.5 0.458,0.198 10 false H46 2.979,6.313 3.438,6.51 0.458,0.198 10 false 24 2.979,6.75 3.438,6.948 0.458,0.198 10 false 11 3.01,7.135 3.469,7.333 0.458,0.198 10 false 6 0.656,8.052 1.906,8.438 1.25,0.385 10 false Auxiliary Battery 0.625,7.656 2.688,7.958 2.063,0.302 10 false Fusible Link Block Assembly 0.531,6.698 1.854,6.896 1.323,0.198 10 false BATT-MAIN NO. 1 0.333,6.26 0.792,6.458 0.458,0.198 10 false A81 0.135,6.229 0.594,6.427 0.458,0.198 10 false 1 1.094,5.323 2.063,5.531 0.969,0.208 10 false IGP-MAIN 5.156,4.146 5.615,4.344 0.458,0.198 10 false 4C 5.167,3.969 5.625,4.167 0.458,0.198 10 false 41 1.552,4.375 2.01,4.573 0.458,0.198 10 false 4B 1.25,4.375 1.708,4.573 0.458,0.198 10 false 11 3.042,4.375 3.5,4.573 0.458,0.198 10 false 4D 2.74,4.365 3.198,4.563 0.458,0.198 10 false 13 1.51,2.844 1.969,3.042 0.458,0.198 10 false IC 0.833,2.854 1.292,3.052 0.458,0.198 10 false 4H 0.875,2.635 1.333,2.833 0.458,0.198 10 false 1 1.615,6.271 2.073,6.469 0.458,0.198 10 false A80 1.385,6.24 1.802,6.427 0.417,0.188 10 false 1 0.594,7.344 1.917,7.542 1.323,0.198 10 false INP STD NO. 1-3

A490641E01
5.938,0.375 6.396,0.573 0.458,0.198 10 false A67 6.281,0.365 6.74,0.563 0.458,0.198 10 false +B 6,0.198 6.458,0.396 0.458,0.198 10 false 1 4.708,0.552 5.417,0.802 0.708,0.25 10 false EFI NO. 3 2.76,1.125 3.906,1.354 1.146,0.229 10 false EFI-MAIN NO. 1 0.927,0.958 2.073,1.188 1.146,0.229 10 false EFI-MAIN NO. 1 0.146,0.094 2.698,0.438 2.552,0.344 12 false w/o Entry and Start System: 3.635,0.677 4.094,0.875 0.458,0.198 10 false 1 3.635,0.26 4.094,0.458 0.458,0.198 10 false 3 2.719,0.688 3.177,0.885 0.458,0.198 10 false 2 2.698,0.281 3.156,0.479 0.458,0.198 10 false 5 4.49,1.698 5.198,1.948 0.708,0.25 10 false INJ 2.333,1.552 2.792,1.75 0.458,0.198 10 false A54 2.323,1.969 2.781,2.167 0.458,0.198 10 false A54 2.354,1.792 2.813,1.99 0.458,0.198 10 false 13 2.385,1.365 2.844,1.563 0.458,0.198 10 false 2 1.969,1.542 2.427,1.74 0.458,0.198 10 false IGP 1.979,1.927 2.438,2.125 0.458,0.198 10 false IGR 1.552,2.271 2.01,2.469 0.458,0.198 10 false ECM 5.938,3.302 6.396,3.5 0.458,0.198 10 false H43 5.979,3.125 6.438,3.323 0.458,0.198 10 false 21 6.292,3.313 6.75,3.51 0.458,0.198 10 false IGR 6.292,5.385 6.75,5.583 0.458,0.198 10 false IGP 6.292,6 6.75,6.198 0.458,0.198 10 false DGND 6.031,6.333 7.073,7.094 1.042,0.76 10 false Engine Stop and Start ECU 5.917,5.396 6.375,5.594 0.458,0.198 10 false H43 5.938,6.01 6.396,6.208 0.458,0.198 10 false A67 5.958,5.208 6.417,5.406 0.458,0.198 10 false 18 6.01,5.833 6.469,6.031 0.458,0.198 10 false 6 4.438,5.583 5.583,5.813 1.146,0.229 10 false ECU-IGP NO. 3 1.375,4.417 4.26,4.76 2.885,0.344 10 false Power Distribution Box Assembly 4.063,2.99 5.208,3.219 1.146,0.229 10 false ECU-IGR NO. 1 4.073,3.448 5.219,3.677 1.146,0.229 10 false ECU-IGR NO. 4 5.229,2.854 5.688,3.052 0.458,0.198 10 false 4D 5.229,2.677 5.688,2.875 0.458,0.198 10 false 22 5.229,3.313 5.688,3.51 0.458,0.198 10 false 4B 5.229,3.115 5.688,3.313 0.458,0.198 10 false 10 2.875,4.031 4.021,4.26 1.146,0.229 10 false IGR-NO. 1 5.229,3.708 5.688,3.906 0.458,0.198 10 false 4C 5.229,3.531 5.688,3.729 0.458,0.198 10 false 17 0.844,3.302 1.302,3.5 0.458,0.198 10 false 4B 0.885,3.104 1.344,3.302 0.458,0.198 10 false 4 1.458,3.438 1.917,3.635 0.458,0.198 10 false AM2 2.625,5.292 3.083,5.49 0.458,0.198 10 false 3 3.604,5.271 4.063,5.469 0.458,0.198 10 false 5 2.625,4.875 3.083,5.073 0.458,0.198 10 false 2 3.604,4.854 4.063,5.052 0.458,0.198 10 false 1 3.042,5.75 3.5,5.948 0.458,0.198 10 false IGP 2.833,7.771 5.719,8.115 2.885,0.344 10 false Ignition or Starter Switch Assembly 2.885,7.063 3.344,7.26 0.458,0.198 10 false AM1 4.052,7.042 4.51,7.24 0.458,0.198 10 false IG1 2.833,7.594 3.292,7.792 0.458,0.198 10 false H54 4.396,7.042 4.854,7.24 0.458,0.198 10 false 8 2.688,7.042 3.146,7.24 0.458,0.198 10 false 7 0.635,8.01 1.885,8.396 1.25,0.385 10 false Auxiliary Battery 0.646,7.635 2.708,7.938 2.063,0.302 10 false Fusible Link Block Assembly 0.479,6.719 1.771,6.938 1.292,0.219 10 false BATT-MAIN NO. 1 0.292,6.24 0.75,6.438 0.458,0.198 10 false A81 0.115,6.198 0.573,6.396 0.458,0.198 10 false 1 0.635,5.552 1.604,5.76 0.969,0.208 10 false IGP-MAIN 4.146,4.375 4.604,4.573 0.458,0.198 10 false 4D 4.469,4.385 4.927,4.583 0.458,0.198 10 false 13 0.844,3.719 1.302,3.917 0.458,0.198 10 false 4C 0.854,3.521 1.313,3.719 0.458,0.198 10 false 41 0.833,2.854 1.292,3.052 0.458,0.198 10 false 4H 0.885,2.646 1.344,2.844 0.458,0.198 10 false 1 1.552,2.854 2.01,3.052 0.458,0.198 10 false IC 0.594,7.365 1.885,7.583 1.292,0.219 10 false INP STD NO. 1-3 1.573,6.24 2.031,6.438 0.458,0.198 10 false A80 1.385,6.208 1.844,6.406 0.458,0.198 10 false 1


for 1KR-FE


A490640E02
5.906,0.375 6.365,0.573 0.458,0.198 10 false A67 6.281,0.365 6.74,0.563 0.458,0.198 10 false +B 5.969,0.198 6.427,0.396 0.458,0.198 10 false 1 4.865,0.552 5.573,0.802 0.708,0.25 10 false EFI NO. 3 3.094,1.125 4.24,1.354 1.146,0.229 10 false EFI-MAIN NO. 1 1.01,0.958 2.156,1.188 1.146,0.229 10 false EFI-MAIN NO. 1 0.146,0.094 2.698,0.438 2.552,0.344 12 false w/ Entry and Start System: 4.094,0.688 4.552,0.885 0.458,0.198 10 false 1 2.969,0.271 3.427,0.469 0.458,0.198 10 false 3 2.969,0.688 3.427,0.885 0.458,0.198 10 false 2 4.115,0.271 4.573,0.469 0.458,0.198 10 false 5 4.448,1.698 5.156,1.948 0.708,0.25 10 false INJ 2.323,1.531 2.781,1.729 0.458,0.198 10 false A55 2.323,1.948 2.781,2.146 0.458,0.198 10 false A55 2.354,1.781 2.813,1.979 0.458,0.198 10 false 31 2.365,1.365 2.823,1.563 0.458,0.198 10 false 37 1.833,1.542 2.292,1.74 0.458,0.198 10 false IGSW 1.979,1.927 2.438,2.125 0.458,0.198 10 false IGR 1.552,2.271 2.01,2.469 0.458,0.198 10 false ECM 5.906,3.708 6.365,3.906 0.458,0.198 10 false H43 5.958,3.531 6.417,3.729 0.458,0.198 10 false 21 6.271,3.698 6.729,3.896 0.458,0.198 10 false IGR 6.26,5.167 6.719,5.365 0.458,0.198 10 false IGP 6.26,5.594 6.719,5.792 0.458,0.198 10 false DGND 6.063,5.917 7.104,6.677 1.042,0.76 10 false Engine Stop and Start ECU 5.917,5.167 6.375,5.365 0.458,0.198 10 false H43 5.906,5.604 6.365,5.802 0.458,0.198 10 false A67 5.948,4.979 6.406,5.177 0.458,0.198 10 false 18 5.979,5.427 6.438,5.625 0.458,0.198 10 false 6 4.635,5.323 5.781,5.552 1.146,0.229 10 false ECU-IGP NO. 3 3.417,4.427 6.302,4.771 2.885,0.344 10 false Power Distribution Box Assembly 4.042,3.031 5.188,3.26 1.146,0.229 10 false ECU-IGR NO. 1 4,3.875 5.146,4.104 1.146,0.229 10 false ECU-IGR NO. 4 5.167,2.844 5.625,3.042 0.458,0.198 10 false 4D 5.167,2.677 5.625,2.875 0.458,0.198 10 false 22 5.167,3.708 5.625,3.906 0.458,0.198 10 false 4B 5.156,3.521 5.615,3.719 0.458,0.198 10 false 10 2.823,3.594 3.969,3.823 1.146,0.229 10 false IGR-NO. 1 3.042,4.375 3.5,4.573 0.458,0.198 10 false 4D 1.99,4.375 2.448,4.573 0.458,0.198 10 false 17 0.833,3.354 1.292,3.552 0.458,0.198 10 false 4B 0.875,3.146 1.333,3.344 0.458,0.198 10 false 9 1.417,3.5 1.875,3.698 0.458,0.198 10 false AM2 3.26,5.052 3.719,5.25 0.458,0.198 10 false 3 4.146,5.052 4.604,5.25 0.458,0.198 10 false 5 3.25,5.479 3.708,5.677 0.458,0.198 10 false 1 4.146,5.479 4.604,5.677 0.458,0.198 10 false 2 3.625,5.885 4.083,6.083 0.458,0.198 10 false IGP 3.24,7.667 6.125,8.01 2.885,0.344 10 false Certification ECU (Smart Key ECU Assembly) 3.313,6.5 3.771,6.698 0.458,0.198 10 false IGPD 3.302,6.927 3.76,7.125 0.458,0.198 10 false IGRD 3.323,7.333 3.781,7.531 0.458,0.198 10 false +B 2.938,6.5 3.396,6.698 0.458,0.198 10 false H45 2.938,6.927 3.396,7.125 0.458,0.198 10 false H45 2.927,7.302 3.385,7.5 0.458,0.198 10 false H46 2.979,6.313 3.438,6.51 0.458,0.198 10 false 24 2.979,6.75 3.438,6.948 0.458,0.198 10 false 11 3,7.135 3.458,7.333 0.458,0.198 10 false 6 0.656,8.042 1.906,8.427 1.25,0.385 10 false Auxiliary Battery 0.615,7.667 2.677,7.969 2.063,0.302 10 false Fusible Link Block Assembly 0.51,6.719 1.813,7 1.302,0.281 10 false BATT-MAIN NO. 1 0.333,6.26 0.792,6.458 0.458,0.198 10 false A81 0.146,6.229 0.604,6.427 0.458,0.198 10 false 1 1.094,5.344 2.063,5.552 0.969,0.208 10 false IGP-MAIN 5.167,3.979 5.625,4.177 0.458,0.198 10 false 41 5.167,4.156 5.625,4.354 0.458,0.198 10 false 4C 2.281,4.375 2.74,4.573 0.458,0.198 10 false 4C 2.75,4.365 3.208,4.563 0.458,0.198 10 false 13 1.563,4.365 2.021,4.563 0.458,0.198 10 false 4B 1.25,4.375 1.708,4.573 0.458,0.198 10 false 11 1.51,2.854 1.969,3.052 0.458,0.198 10 false IC 0.833,2.854 1.292,3.052 0.458,0.198 10 false 4H 0.865,2.635 1.323,2.833 0.458,0.198 10 false 1 1.625,6.271 2.083,6.469 0.458,0.198 10 false A80 1.417,6.229 1.875,6.427 0.458,0.198 10 false 1 0.594,7.354 1.896,7.635 1.302,0.281 10 false INP STD NO. 1-3

A490641E03
5.938,0.375 6.396,0.573 0.458,0.198 10 false A67 6.281,0.365 6.74,0.563 0.458,0.198 10 false +B 6,0.198 6.458,0.396 0.458,0.198 10 false 1 4.708,0.552 5.417,0.802 0.708,0.25 10 false EFI NO. 3 2.76,1.125 3.906,1.354 1.146,0.229 10 false EFI-MAIN NO. 1 0.927,0.958 2.073,1.188 1.146,0.229 10 false EFI-MAIN NO. 1 0.146,0.094 2.698,0.438 2.552,0.344 12 false w/o Entry and Start System: 3.635,0.677 4.094,0.875 0.458,0.198 10 false 1 2.708,0.271 3.167,0.469 0.458,0.198 10 false 3 2.719,0.688 3.177,0.885 0.458,0.198 10 false 2 3.646,0.271 4.104,0.469 0.458,0.198 10 false 5 4.49,1.698 5.198,1.948 0.708,0.25 10 false INJ 2.333,1.552 2.792,1.75 0.458,0.198 10 false A55 2.323,1.969 2.781,2.167 0.458,0.198 10 false A55 2.354,1.792 2.813,1.99 0.458,0.198 10 false 31 2.385,1.365 2.844,1.563 0.458,0.198 10 false 37 1.823,1.542 2.281,1.74 0.458,0.198 10 false IGSW 1.979,1.927 2.438,2.125 0.458,0.198 10 false IGR 1.552,2.271 2.01,2.469 0.458,0.198 10 false ECM 5.938,3.302 6.396,3.5 0.458,0.198 10 false H43 5.979,3.125 6.438,3.323 0.458,0.198 10 false 21 6.292,3.313 6.75,3.51 0.458,0.198 10 false IGR 6.292,5.385 6.75,5.583 0.458,0.198 10 false IGP 6.292,6 6.75,6.198 0.458,0.198 10 false DGND 6.031,6.333 7.073,7.094 1.042,0.76 10 false Engine Stop and Start ECU 5.917,5.396 6.375,5.594 0.458,0.198 10 false H43 5.938,6.01 6.396,6.208 0.458,0.198 10 false A67 5.958,5.208 6.417,5.406 0.458,0.198 10 false 18 6.01,5.833 6.469,6.031 0.458,0.198 10 false 6 4.438,5.583 5.583,5.813 1.146,0.229 10 false ECU-IGP NO. 3 1.333,4.396 4.219,4.74 2.885,0.344 10 false Power Distribution Box Assembly 4.042,3.01 5.188,3.24 1.146,0.229 10 false ECU-IGR NO. 1 4.042,3.469 5.188,3.698 1.146,0.229 10 false ECU-IGR NO. 4 5.229,2.854 5.688,3.052 0.458,0.198 10 false 4D 5.229,2.677 5.688,2.875 0.458,0.198 10 false 22 5.229,3.313 5.688,3.51 0.458,0.198 10 false 4B 5.229,3.115 5.688,3.313 0.458,0.198 10 false 10 2.875,4.01 4.021,4.24 1.146,0.229 10 false IGR-NO. 1 5.229,3.708 5.688,3.906 0.458,0.198 10 false 4C 5.229,3.531 5.688,3.729 0.458,0.198 10 false 17 0.844,3.302 1.302,3.5 0.458,0.198 10 false 4B 0.875,3.104 1.333,3.302 0.458,0.198 10 false 4 1.458,3.448 1.917,3.646 0.458,0.198 10 false AM2 2.625,5.292 3.083,5.49 0.458,0.198 10 false 3 3.604,5.26 4.063,5.458 0.458,0.198 10 false 5 2.625,4.875 3.083,5.073 0.458,0.198 10 false 2 3.604,4.854 4.063,5.052 0.458,0.198 10 false 1 3.042,5.75 3.5,5.948 0.458,0.198 10 false IGP 2.833,7.771 5.719,8.115 2.885,0.344 10 false Ignition or Starter Switch Assembly 2.885,7.063 3.344,7.26 0.458,0.198 10 false AM1 4.052,7.042 4.51,7.24 0.458,0.198 10 false IG1 2.833,7.594 3.292,7.792 0.458,0.198 10 false H54 4.396,7.042 4.854,7.24 0.458,0.198 10 false 8 2.688,7.042 3.146,7.24 0.458,0.198 10 false 7 0.677,8.042 1.927,8.427 1.25,0.385 10 false Auxiliary Battery 0.646,7.656 2.708,7.958 2.063,0.302 10 false Fusible Link Block Assembly 0.469,6.719 1.698,7.125 1.229,0.406 10 false BATT-MAIN NO. 1 0.292,6.24 0.75,6.438 0.458,0.198 10 false A81 0.104,6.198 0.563,6.396 0.458,0.198 10 false 1 0.635,5.552 1.604,5.76 0.969,0.208 10 false IGP-MAIN 4.146,4.375 4.604,4.573 0.458,0.198 10 false 4D 4.469,4.385 4.927,4.583 0.458,0.198 10 false 13 0.833,3.708 1.292,3.906 0.458,0.198 10 false 4C 0.844,3.521 1.302,3.719 0.458,0.198 10 false 41 0.865,2.656 1.323,2.854 0.458,0.198 10 false 1 0.833,2.854 1.292,3.052 0.458,0.198 10 false 4H 1.573,6.229 2.031,6.427 0.458,0.198 10 false A80 1.375,6.198 1.833,6.396 0.458,0.198 10 false 1 0.594,7.354 1.823,7.76 1.229,0.406 10 false INP STD NO. 1-3 1.552,2.844 2.01,3.042 0.458,0.198 10 false IC


CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU, perform learning of the external backup boost converter (eco run vehicle converter assembly).

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

for CVT:

When the engine stop and start ECU or oil pump with motor assembly is replaced, check the oil pump with motor assembly.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

When the ECM is replaced on a vehicle with a non-specified auxiliary battery, it is necessary to perform auxiliary battery type switching.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA

·

For wire harness and connector inspection procedures and precautions, refer to "General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE"

·

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.READ VALUE USING GTS (IG SWITCH)
a.

Enter the following menus: Powertrain / Stop and Start / Data List / IG Switch.

Powertrain > Stop and Start > Data List
Tester Display
IG Switch
50003 392 203

b.

Read the value displayed on the GTS.

Result:
Tester Display Result Proceed to
IG Switch ON A
IG Switch OFF B




A

B

2.CHECK ENGINE STOP AND START ECU (IGP TERMINAL VOLTAGE)
2.CHECK ENGINE STOP AND START ECU (IGP TERMINAL VOLTAGE)
A454171C19
4.625,0.479 5.146,0.792 0.521,0.313 5.385,2.135 5.083,1.531 true 5.396,2.177 6.052,2.365 0.656,0.188 10 false IGP 4.75,0.542 5.125,0.74 0.375,0.198 10 false H43 0.104,0.073 0.885,0.271 0.781,0.198 10 false *a
*a Component with harness connected
(Engine Stop and Start ECU)
- -


a.

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H43-18 (IGP) - Body ground Ignition switch ON 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE STOP AND START ECU (+B TERMINAL VOLTAGE)

NG

13.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - POWER DISTRIBUTION BOX ASSEMBLY (IGR-NO. 1 RELAY))
3.CHECK ENGINE STOP AND START ECU (+B TERMINAL VOLTAGE)
A476766C08
3.26,0.094 3.646,0.365 0.385,0.271 4.063,0.854 4.146,1.458 true 0.865,0.135 1.177,0.333 0.313,0.198 10 false *a 4.073,1.5 4.688,1.698 0.615,0.198 10 false +B 3.344,0.156 3.958,0.354 0.615,0.198 10 false A67
*a Component with harness connected
(Engine Stop and Start ECU)
- -


a.

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A67-1 (+B) - Body ground Ignition switch ON 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

NG

4.CHECK VEHICLE SPECIFICATION
4.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification.


Result:
Result Proceed to
for M15A-FKS A
for 1KR-FE B



A

5.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EFI-MAIN NO. 1 RELAY)

B

9.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EFI-MAIN NO. 1 RELAY)
5.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EFI-MAIN NO. 1 RELAY)
a.

Disconnect the A67 engine stop and start ECU connector.


b.

Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition
A67-1 (+B) - 3 (EFI-MAIN NO. 1 relay holder) Always Below 1 Ω
A67-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
3 (EFI-MAIN NO. 1 relay holder) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT POWER DISTRIBUTION BOX ASSEMBLY (EFI-MAIN NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT POWER DISTRIBUTION BOX ASSEMBLY (EFI-MAIN NO. 1 RELAY)
a.

Inspect the EFI-MAIN NO. 1 relay.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - BODY GROUND)

NG

REPLACE EFI-MAIN NO. 1 RELAY

7.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - BODY GROUND)
a.

Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (EFI-MAIN NO. 1 relay holder) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - POWER SOURCE)
a.
A456559C01
0.188,0.74 0.5,0.938 0.313,0.198 10 false *1 2.24,0.365 2.552,0.563 0.313,0.198 10 false *a
*1 Component without harness connected
(No. 1 Engine Room Relay Block)
*a EFI-MAIN NO. 1 Relay Holder


Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2 (EFI-MAIN NO. 1 relay holder) - Body ground Always 9.5 to 14 V
5 (EFI-MAIN NO. 1 relay holder) - Body ground Always 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EFI-MAIN NO. 1 RELAY)
a.

Disconnect the A67 engine stop and start ECU connector.


b.

Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition
A67-1 (+B) - 5 (EFI-MAIN NO. 1 relay holder) Always Below 1 Ω
A67-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
5 (EFI-MAIN NO. 1 relay holder) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.INSPECT POWER DISTRIBUTION BOX ASSEMBLY (EFI-MAIN NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT POWER DISTRIBUTION BOX ASSEMBLY (EFI-MAIN NO. 1 RELAY)

Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - BODY GROUND)

NG

REPLACE EFI-MAIN NO. 1 RELAY

11.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - BODY GROUND)
a.

Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (EFI-MAIN NO. 1 relay holder) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - POWER SOURCE)
a.
A456559C01
0.188,0.74 0.5,0.938 0.313,0.198 10 false *1 2.24,0.365 2.552,0.563 0.313,0.198 10 false *a
*1 Component without harness connected
(No. 1 Engine Room Relay Block)
*a EFI-MAIN NO. 1 Relay Holder


Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2 (EFI-MAIN NO. 1 relay holder) - Body ground Always 9.5 to 14 V
3 (EFI-MAIN NO. 1 relay holder) - Body ground Always 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - POWER DISTRIBUTION BOX ASSEMBLY (IGR-NO. 1 RELAY))
a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the 4B power distribution box assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H43-21 (IGR) - 4B-10 Always Below 1 Ω
H43-21 (IGR) - Body ground and other terminals Always 10 kΩ or higher
4B-10 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.CHECK VEHICLE SPECIFICATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Entry and Start System A
w/o Entry and Start System B



A

B

15.INSPECT POWER DISTRIBUTION BOX ASSEMBLY (IGR-NO. 1 RELAY)
15.INSPECT POWER DISTRIBUTION BOX ASSEMBLY (IGR-NO. 1 RELAY)
a.

Remove the power distribution box assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4B-10 (voltmeter positive (+) lead) - 4B-4 (voltmeter negative (-) lead) Auxiliary battery voltage not applied to terminals 4C-17 (auxiliary battery positive (+)) and 4C-41 (auxiliary battery negative (-)) Below 1 V
4B-10 (voltmeter positive (+) lead) - 4B-4 (voltmeter negative (-) lead) Auxiliary battery applied to terminals 4C-17 (auxiliary battery positive (+)) and 4C-41 (auxiliary battery negative (-)) 11 to 14 V



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - POWER SOURCE)

NG

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

16.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - POWER SOURCE)
a.

Disconnect the 4C power distribution box assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4C-41 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR