Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for HV Model TMMF Made RHD) › from 2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0432223 BRAKE ACTUATOR(for HV Model TMMF Made RHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for HV Model TMMF Made RHD)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

After performing the update ECU security key procedure, make sure to perform the initialization procedure for when the cable has been disconnected and reconnected to the negative (-) auxiliary battery terminal.


HINT:
w/ Electric Parking Brake System:

The parking brake indicator light blinks (red) when the ignition switch is turned on after replacing the brake actuator assembly. Operate the electric parking brake switch assembly to turn off the parking brake indicator light.


PROCEDURE

Hide 44547B 1.INSTALL BRAKE ACTUATOR BRACKET CUSHION

a.

Install the 3 brake actuator bracket cushions to the brake actuator bracket assembly.


Hide 44521A 2.INSTALL NO. 1 BRAKE ACTUATOR CASE COLLAR

a.

Install the 3 No. 1 brake actuator case collars to the brake actuator bracket cushion.

NOTICE:

Make sure that the No. 1 brake actuator case collar is in full contact with the brake actuator bracket cushion.



Hide 44510 3.INSTALL BRAKE ACTUATOR ASSEMBLY

a.

Temporarily install the brake actuator assembly with the 3 bolts.


b.
C436268N01
1.188,1.896 1.375,2.083 0.188,0.188 10 true 1 2.052,0.875 2.24,1.063 0.188,0.188 10 true 2 0.896,0.833 1.083,1.021 0.188,0.188 10 true 3

Fully tighten the 3 bolts in the order shown in the illustration.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:
·

Do not remove the hole plugs of a new brake actuator assembly before connecting the brake lines because the brake actuator assembly is filled with brake fluid.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator assembly when carrying it.




Hide 44591 4.INSTALL NO. 1 BRAKE ACTUATOR BRACKET

a.

Install the No. 1 brake actuator bracket to the brake actuator bracket assembly with the 3 nuts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 5.INSTALL BRAKE ACTUATOR WITH BRACKET

a.

Temporarily install the brake actuator with bracket to the vehicle body with the bolt and 2 nuts.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator with bracket when carrying it.



HINT:

Install the brake actuator with bracket while avoiding the brake lines.



b.
C436271

Tighten the bolt.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


c.
C436272C01
1.146,2.115 1.813,2.229 1.813,2.229 1.229,2.313 true 0.344,1.396 0.594,1.604 0.25,0.208 10 true *a 1.833,2.115 2.281,2.313 0.448,0.198 10 true SST
*a Torque Wrench Fulcrum Length


Using SST, tighten the nut.

SST
09729-00120  
09925-40010  (09925-04120)

Torque:
Specified tightening torque : 19 N*m (194 kgf*cm, 14 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 200 mm (7.87 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 8.5 N*m (87 kgf*cm, 75 in.*lbf)




d.
C436273C01
1.458,2.396 2.104,2.167 2.104,2.167 1.583,2.5 true 1.948,2.854 2.198,3.063 0.25,0.208 10 true *a 2.125,2.073 2.573,2.271 0.448,0.198 10 true SST
*a Torque Wrench Fulcrum Length


Using SST, tighten the nut.

SST
09729-00120  
09925-40010  (09925-04120)

Torque:
Specified tightening torque : 19 N*m (194 kgf*cm, 14 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 200 mm (7.87 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 8.5 N*m (87 kgf*cm, 75 in.*lbf)




e.

Engage the clamp to install the wire harness to the No. 1 brake actuator bracket.


f.

Connect the connector.


g.
C436263C01
2.969,1.74 2.51,1.365 true 1.844,1.833 2.198,1.615 true 1.833,1.417 1.448,1.448 true 1.365,1.063 2.063,1.25 true 2.51,0.313 2.25,1.042 true 2.781,0.698 2.385,0.969 true 2.969,1.667 3.208,1.875 0.24,0.208 10 true *a 1.646,1.823 1.885,2.021 0.24,0.198 10 true *b 1.208,1.354 1.469,1.563 0.26,0.208 10 true *c 1.146,0.938 1.365,1.135 0.219,0.198 10 true *d 2.417,0.115 2.604,0.313 0.188,0.198 10 true *e 2.792,0.604 3.021,0.833 0.229,0.229 10 true *f
*a From 1st Chamber of Brake Booster with Master Cylinder Assembly
*b From 2nd Chamber of Brake Booster with Master Cylinder Assembly
*c To Front Wheel Cylinder Assembly LH
*d To Rear Wheel Cylinder Assembly RH
*e To Rear Wheel Cylinder Assembly LH
*f To Front Wheel Cylinder Assembly RH


Temporarily tighten the 6 brake lines to the correct positions on the brake actuator assembly as shown in the illustration.


h.
C436274C01
1.76,3.042 2.073,3.198 0.313,0.156 10 false *a 1.5,1.688 1.667,1.865 0.167,0.177 10 true A 1.802,1.552 1.979,1.729 0.177,0.177 10 true A 2.51,1.031 2.688,1.208 0.177,0.177 10 true A 2.698,0.667 2.875,0.844 0.177,0.177 10 true A 2.375,1.667 2.552,1.844 0.177,0.177 10 true B 2.167,1.938 2.344,2.115 0.177,0.177 10 true B
*a Torque Wrench Fulcrum Length


Using a union nut wrench, fully tighten the 6 brake lines.

Torque:
Specified tightening torque (A) : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)
Specified tightening torque (B) : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

(A): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

(B): 17.4 N*m (177 kgf*cm, 13 ft.*lbf)




i.
C436275C01
0,0 0,0 false
V113147

Connect the connector
V113148

Lock the lock lever


Connect the connector to the brake actuator assembly and lock the lock lever as shown in the illustration.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the connector can be connected smoothly.

·

Do not allow water, oil or dirt to enter.




Hide 821H1 6.INSTALL FLOOR UNDER WIRE

CAUTION:

Be sure to wear insulated gloves.


a.

Install the HV floor under wire to the vehicle body with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide G9200 7.INSTALL INVERTER WITH CONVERTER ASSEMBLY

Hide 8.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 15. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART