Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for HV Model LHD) › from 2020.07
RM36W0E _54 Brake _088656 BRAKE SYSTEM (OTHER) _0432269 BRAKE BOOSTER(for HV Model LHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for HV Model LHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during brake booster with master cylinder assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Electric brake booster (brake booster with master cylinder assembly)
1.

Bleed air

2.

Perform "Reset Memory"

3.

Perform calibration (brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Update ECU security key Vehicle control history (RoB) are stored (Click here)

NOTICE:

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide G9200 1.REMOVE INVERTER WITH CONVERTER ASSEMBLY

Hide 2.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 82111 3.SEPARATE ENGINE ROOM MAIN WIRE

a.
C438748

Disconnect the connector.


b.

Disengage the clamp.


c.
C436710C01
0,0 0,0 false
V113147

Push in this direction
V113148

Disconnect the connector


Disconnect the connector from the brake master cylinder reservoir assembly as shown in the illustration.


d.
C439809C01
0,0 0,0 false
V113147

Release the lock lever
V113148

Disconnect the connector


Release the lock lever and disconnect the connector from the booster with master cylinder assembly.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



e.
C439810

Remove the bolt to separate the engine room main wire.


f.

Disengage the clamp.


Hide 4.DISCONNECT BRAKE LINE

a.
C436712

Using a union nut wrench, disconnect the 2 brake lines from the brake master cylinder sub-assembly.

NOTICE:
·

Do not damage or deform the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




b.
C439833

Disengage the 8 clamps to remove the No. 1 brake tube clamp and No. 5 brake tube clamp from the brake lines.


c.
C439832

Using a union nut wrench, disconnect the brake line from the front No. 2 brake tube way.

NOTICE:
·

Do not damage or deform the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




d.
C439834

Using a union nut wrench, disconnect the brake line from the front flexible hose.


Hide 55606 5.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 45259A 6.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45260 7.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 47101A 8.REMOVE BRAKE PEDAL RETURN SPRING

Hide 47210L 10.REMOVE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

a.
C439811C01
1.771,2.667 1.604,2.354 1.604,2.354 1.51,2.354 false 2.521,2.833 2.635,2.406 2.635,2.406 2.75,2.406 false 1.292,4.094 1.625,4.094 false 2.885,2.958 3.01,3.427 3.01,3.427 3.125,3.427 false 0.729,3.406 0.594,3.781 0.594,3.781 0.5,3.781 false 1.073,4 1.385,4.156 0.313,0.156 10 false *a 1.313,2.26 1.625,2.417 0.313,0.156 10 false *b 2.813,2.323 3.125,2.479 0.313,0.156 10 false *c 3.146,3.354 3.385,3.573 0.24,0.219 10 false *d 0.313,3.698 0.625,3.854 0.313,0.156 10 false *e
*a ECU Connector
*b Connector
*c Boot
*d Brake Master Cylinder Push Rod Clevis
*e Brake Master Cylinder Reservoir Assembly


Remove the 4 nuts and brake booster with master cylinder assembly.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not carry the brake booster with master cylinder assembly by the parts shown in the illustration.

·

Be careful not to allow any brake fluid to enter the connector.




Hide 44785 11.REMOVE BRAKE BOOSTER GASKET

a.

Remove the brake booster gasket from the brake booster with master cylinder assembly.