Home › Vehicle Interior › INTERIOR PANELS / TRIM › INSTRUMENT PANEL SAFETY PAD › 2020.07–2020.09
RM36W0E _58 Vehicle Interior _087984 INTERIOR PANELS / TRIM _0420190 INSTRUMENT PANEL SAFETY PAD A

INTERIOR PANELS / TRIM  INSTRUMENT PANEL SAFETY PAD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during instrument panel sub-assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)

CAUTION:
B475753

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: for Gasoline Model

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system *1 Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2. TABLE OF BOLT, SCREW AND NUT

HINT:

All bolts and screws relevant to installing and removing the instrument panel are shown along with their alphabetic code in the table below.

B572752E02
0.208,0.583 0.823,0.781 0.615,0.198 10 false Code 2.479,0.563 3.094,0.76 0.615,0.198 10 false Code 4.74,0.563 5.354,0.76 0.615,0.198 10 false Code 1.208,0.573 1.823,0.771 0.615,0.198 10 false Shape 3.396,0.583 4.01,0.781 0.615,0.198 10 false Shape 5.708,0.573 6.323,0.771 0.615,0.198 10 false Shape 0.229,1.406 0.844,1.604 0.615,0.198 10 false <A> 0.24,2.552 0.854,2.75 0.615,0.198 10 false <D> 0.229,3.708 0.844,3.906 0.615,0.198 10 false <G> 2.51,1.385 3.125,1.583 0.615,0.198 10 false <B> 2.51,2.531 3.125,2.729 0.615,0.198 10 false <E> 2.521,3.698 3.135,3.896 0.615,0.198 10 false <H> 4.781,1.385 5.396,1.583 0.615,0.198 10 false <C> 4.792,2.542 5.406,2.74 0.615,0.198 10 false <F> 4.813,3.698 5.427,3.896 0.615,0.198 10 false <I> 5.781,4.427 7.073,4.677 1.292,0.25 10 false mm (in.) (L=Length) 1.927,1.323 2.448,1.552 0.521,0.229 10 false (0.197) 1.958,1.115 2.271,1.313 0.313,0.198 10 false φ5 1.948,1.531 2.365,1.729 0.417,0.198 10 false L=14 1.938,1.74 2.458,1.969 0.521,0.229 10 false (0.551) 1.969,2.26 2.281,2.458 0.313,0.198 10 false φ5 1.927,2.458 2.448,2.688 0.521,0.229 10 false (0.197) 4.25,2.656 4.698,2.854 0.448,0.198 10 false L=19 1.938,2.844 2.458,3.073 0.521,0.229 10 false (0.708) 1.958,3.385 2.271,3.583 0.313,0.198 10 false φ8 1.938,3.583 2.458,3.813 0.521,0.229 10 false (0.315) 1.958,3.792 2.406,3.99 0.448,0.198 10 false L=21 1.927,3.979 2.448,4.208 0.521,0.229 10 false (0.827) 4.25,0.979 4.563,1.177 0.313,0.198 10 false φ5 4.219,1.198 4.74,1.427 0.521,0.229 10 false (0.197) 4.24,1.615 4.656,1.813 0.417,0.198 10 false L=20 4.208,1.813 4.729,2.042 0.521,0.229 10 false (0.787) 4.26,2.26 4.573,2.458 0.313,0.198 10 false φ8 4.229,2.458 4.75,2.688 0.521,0.229 10 false (0.315) 1.948,2.656 2.396,2.854 0.448,0.198 10 false L=18 4.219,2.833 4.74,3.063 0.521,0.229 10 false (0.748) 4.26,3.396 4.573,3.594 0.313,0.198 10 false φ6 4.229,3.594 4.75,3.823 0.521,0.229 10 false (0.236) 4.24,3.792 4.688,3.99 0.448,0.198 10 false L=15 4.219,3.979 4.74,4.208 0.521,0.229 10 false (0.591) 6.167,3.563 6.479,3.76 0.313,0.198 10 false φ6 6.146,3.771 6.667,4 0.521,0.229 10 false (0.236) 6.5,2.26 6.813,2.458 0.313,0.198 10 false φ6 6.5,2.458 7.021,2.688 0.521,0.229 10 false (0.236) 6.51,2.656 6.927,2.854 0.417,0.198 10 false L=20 6.49,2.833 7.01,3.063 0.521,0.229 10 false (0.787) 6.5,1.115 6.813,1.313 0.313,0.198 10 false φ6 6.5,1.333 7.021,1.563 0.521,0.229 10 false (0.236) 6.521,1.531 6.938,1.729 0.417,0.198 10 false L=20 6.5,1.74 7.021,1.969 0.521,0.229 10 false (0.787)


Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 4.REMOVE REAR CONSOLE BOX ASSEMBLY

Hide 5.REMOVE HEADLIGHT DIMMER SWITCH ASSEMBLY

Hide 67914B 6.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 67913B 7.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 62112 8.REMOVE COWL SIDE TRIM BOARD LH

Hide 62111C 9.REMOVE COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure as for the LH side.


Hide 55606 10.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

a.
B587130C01
0.417,0.344 0.719,0.521 0.302,0.177 10 true <A> 3.042,0.521 3.354,0.708 0.313,0.188 10 true <A>
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Remove the 2 screws <A>.


b.

Disengage the claws and guide to remove the No. 1 instrument panel under cover sub-assembly as shown in the illustration.


Hide 55607 11.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

a.
B587131C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Disengage the claws and guide to remove the No. 2 instrument panel under cover sub-assembly as shown in the illustration.


Hide 62312B 12.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

a.
B587132

Disconnect the front door opening trim weatherstrip LH from the area shown in the illustration.


Hide 62311B 13.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 55317E 14.REMOVE NO. 1 INSTRUMENT SIDE PANEL

a.
B587133C01
0,0 0,0 false
V100155

Protective Tape
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Using a molding remover A, disengage the clips and guides to remove the No. 1 instrument side panel as shown in the illustration.


b.

for Front Passenger Side with Airbag Cut off Switch:

i.

Disconnect the connector.



Hide 55318F 15.REMOVE NO. 2 INSTRUMENT SIDE PANEL

HINT:

Use the same procedure as for the No. 1 side.


Hide 55550 16.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

a.
B587134C01
2.719,0.781 2.99,0.458 true 0.719,0.969 0.5,0.667 true 0.302,0.51 0.521,0.698 0.219,0.188 10 true *a 2.969,0.344 3.188,0.531 0.219,0.188 10 true *a
*a Stopper
V100135

Push


Disengage the 2 stoppers and pull out the glove compartment door assembly until it is level.


b.

Disengage the claw to separate the glove compartment door stopper sub-assembly from the glove compartment door assembly.


c.
B587135C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the hinges to remove the glove compartment door assembly as shown in the illustration.


Hide 55054 17.REMOVE GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY

a.

Disengage the claw to remove the glove compartment door stopper sub-assembly.


Hide 55433B 18.REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

a.
B587136E01
0.208,1.531 0.521,1.708 0.313,0.177 10 true <D> 1.917,0.542 2.229,0.719 0.313,0.177 10 true <E> 0.865,0.698 1.177,0.875 0.313,0.177 10 true <C> 2.854,0.115 3.167,0.292 0.313,0.177 10 true <D> 0.135,0.052 0.448,0.229 0.313,0.177 10 true <D> 3.063,1.833 3.375,2.01 0.313,0.177 10 true <C>

Remove the 2 screws <C>, 3 screws <D> and screw <E>.


b.
B587137C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws and guides to remove the lower No. 2 instrument panel finish panel as shown in the illustration.


Hide 55557A 19.REMOVE GLOVE COMPARTMENT DOOR CHECK CUSHION

HINT:

Use the same procedure as for the opposite side.


a.
B587138

Disengage the claws to remove the glove compartment door check cushion.


Hide 62212 20.REMOVE FRONT PILLAR GARNISH LH

a.
B587139C01
0,0 0,0 false
V100135

Pull up


Pull up the front pillar garnish LH to disengage the front pillar garnish clip and clip as shown in the illustration.


b.
B587140C01
0.833,0.906 1.333,0.948 1.333,0.948 0.896,0.542 true 1.365,0.896 1.677,1.094 0.313,0.198 10 false *a
*a Release Lever
V100135

Push


Push the release lever and separate the front pillar garnish clip from the vehicle body as shown in the illustration.


c.

When the front pillar garnish clip cannot be removed using your fingers:

i.
B587141C01
0,0 0,0 false
V113147

Lift in this Direction


While pressing the part shown in the illustration with your finger, move the front pillar garnish clip in the direction indicated by the arrow shown in the illustration.


ii.
B587142C01
0,0 0,0 false
V113147

Remove in this Direction


While pulling the front pillar garnish clip in the direction indicated by the arrow, push the part shown in the illustration with the end of a screwdriver and remove the front pillar garnish clip.



d.
B587143C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the guides as shown in the illustration.


e.
B587144

w/ Speaker:

i.

Disengage the claws to disconnect the front No.2 speaker assembly and remove the front pillar garnish LH.



f.
B587145

w/o Speaker:

i.

Disengage the clamp to remove the front pillar garnish LH.



g.

Remove the front pillar garnish clip from the front pillar garnish LH.


h.
B587146C01
1.813,1.385 2.229,1.385 false 1.594,1.271 1.906,1.469 0.313,0.198 10 false *a
*a Protective Cover
V100155

Adhesive Tape


Protect the curtain shield airbag assembly.

i.

Completely cover the curtain shield airbag assembly with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.

NOTICE:

Cover the curtain shield airbag assembly with a protective cover as soon as the front pillar garnish LH is removed.




Hide 62211 21.REMOVE FRONT PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 86160P 22.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for 6 or 8 Speakers)

Hide 53601 23.DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

a.
B587147

Disengage the claw and guides to disconnect the hood lock control lever sub-assembly.


Hide 55480D 24.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

a.
B587148C01
0.677,1.854 0.969,2.01 0.292,0.156 10 true <F>
V113147

Remove in this Direction


Remove the bolt <F>.


b.

Disengage the clips, claw and guide to remove the lower instrument panel finish panel assembly as shown in the illustration.


c.

Disconnect each connector.


Hide 55548A 25.REMOVE INSTRUMENT PANEL HOLE COVER (w/ Cover)

a.
B574305E01
0.333,0.635 0.625,0.802 0.292,0.167 10 true <A> 2.76,1.5 3.052,1.667 0.292,0.167 10 true <A>

Remove the 2 screws <A>.


b.

Disengage the guides to remove the instrument panel hole cover.


Hide 55410C 26.REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (for Analog Meter)

a.
B587150E01
0.073,1.958 0.833,2.125 0.76,0.167 10 true <A> or <B> 2.625,1.969 3.385,2.135 0.76,0.167 10 true <A> or <B>

Remove the 2 screws <A> or 2 screws <B>.


b.
B587151C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the clips, claws and guides to remove the instrument cluster finish panel assembly as shown in the illustration.


Hide 55410C 27.REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (for Digital Meter)

a.
B587152E01
0.052,1.969 0.844,2.146 0.792,0.177 10 true <A> or <B> 2.646,1.969 3.427,2.146 0.781,0.177 10 true <A> or <B>

Remove the 2 screws <A> or 2 screws <B>.


b.
B587153C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the clips, claws and guides to remove the instrument cluster finish panel assembly as shown in the illustration.


Hide 83100 28.REMOVE COMBINATION METER ASSEMBLY (for Analog Meter)

Hide 83100 29.REMOVE COMBINATION METER ASSEMBLY (for Digital Meter)

Hide 55406B 30.REMOVE INSTRUMENT CLUSTER FINISH LOWER CENTER PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)

Hide 55900 31.REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)

Hide 55405B 32.REMOVE INSTRUMENT CLUSTER FINISH CENTER PANEL SUBASSEMBLY

a.
B587154C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the clips, claws and guides to remove the instrument cluster finish center panel sub-assembly as shown in the illustration.


b.
B574309

Disconnect the connector.


Hide 55670A 33.REMOVE INSTRUMENT PANEL CENTER REGISTER ASSEMBLY

a.
B596970C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the locations shown in the illustration.


b.
B596971C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the clips and guides as shown in the illustration.


c.
B596972

Disengage the clamp to remove the instrument panel center register assembly.


Hide 86140A 34.REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (w/ Audio)

Hide 55420A 35.REMOVE INSTRUMENT CLUSTER FINISH CENTER PANEL ASSEMBLY

a.
B587157C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the clips to remove the instrument cluster finish center panel assembly as shown in the illustration.


Hide 55624A 36.REMOVE INSTRUMENT PANEL CENTER TRAY

a.
B587158C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws to remove the instrument panel center tray as shown in the illustration.


Hide 55414A 37.REMOVE INSTRUMENT CLUSTER FINISH END PANEL (w/ Headup Display)

a.
B587159C01
0,0 0,0 false
V100155

Protective Tape
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Using a molding remover A, disengage the claws and guides to remove the instrument cluster finish end panel as shown in the illustration.


Hide 55408F 38.REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY (for 8 Speakers)

a.
B594410C01
0,0 0,0 false
V100155

Protective Tape
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Using a molding remover A, disengage the 5 claws and 2 guides to remove the No. 1 instrument panel speaker sub-assembly as shown in the illustration.


Hide 55409F 39.REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY (for 8 Speakers)

HINT:

Use the same procedure as for the No. 1 side.


Hide 55510F 40.REMOVE NO. 1 SPEAKER OPENING COVER ASSEMBLY (w/ Telematics Transceiver)

a.
B594406C01
0,0 0,0 false
V100155

Protective Tape


Using a molding remover A, disengage the 4 clips to remove the No. 1 speaker opening cover assembly as shown in the illustration.


Hide 86160J 41.REMOVE FRONT NO. 3 SPEAKER ASSEMBLY (w/ Telematics Transceiver)

Hide 55313A 42.REMOVE INSTRUMENT MAIN PANEL (for Separate Type)

a.

Using a molding remover B, disengage the clips and claws as shown in the illustration.

B587160C01
0,0 0,0 false
V100155

Protective Tape
V113147

Remove in this Direction



b.

Disconnect the connectors.

B587161C01
0,0 0,0 false
V113147

Remove in this Direction - -



c.

Disengage the guides to remove the instrument main panel as shown in the illustration.


Hide 86160L 43.REMOVE FRONT NO. 4 SPEAKER ASSEMBLY (for 8 Speakers)

Hide 55302C 44.REMOVE INSTRUMENT PANEL SUB-ASSEMBLY (for Integrated Type)

a.

Disconnect the connector.

B579333C01
1.198,2.375 1.51,2.188 true 2.021,2.375 1.719,2.177 true 0.896,1.5 0.76,1.354 true 0.948,1.448 1.135,1.615 0.188,0.167 10 true *a 1.479,2.083 1.719,2.26 0.24,0.177 10 true *b 4.76,0.917 5.094,1.094 0.333,0.177 10 true <H> 5.229,1.698 5.479,1.875 0.25,0.177 10 true <I> 6.49,2.271 6.781,2.438 0.292,0.167 10 true <F> 4.385,2.5 4.677,2.677 0.292,0.177 10 true <F> 2.51,2.625 2.813,2.792 0.302,0.167 10 true <E> 1.948,2.604 2.25,2.781 0.302,0.177 10 true <G> 1.125,2.594 1.458,2.771 0.333,0.177 10 true <G> 0.344,2.292 0.656,2.469 0.313,0.177 10 true <F>
*a Airbag Connector *b Airbag Bolt



b.

Remove the bolt <H> and disengage the guide to separate the ground bracket.


c.

Remove the 2 bolts <G>.


d.

Disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Refer to How to Connect or Disconnect Airbag Connector:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR



e.

Remove the 4 clips.


f.

Disengage the hooks.


g.

Remove the 3 bolts <F>, screw <E> and nut <I> as shown in the illustration.


h.

Disengage the guides to remove the instrument panel sub-assembly as shown in the illustration.

B580440C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)



Hide 55302C 45.REMOVE INSTRUMENT PANEL SUB-ASSEMBLY (for Separate Type)

a.

Disconnect the connector.

B587164C01
4.906,2.365 5.219,2.177 true 5.76,2.375 5.458,2.177 true 6.354,1.583 6.521,1.458 true 6.198,1.552 6.396,1.719 0.198,0.167 10 true *a 5.219,2.042 5.458,2.219 0.24,0.177 10 true *b 3.458,0.896 3.781,1.063 0.323,0.167 10 true <H> 1.75,1.698 2,1.875 0.25,0.177 10 true <I> 6.5,2.208 6.813,2.385 0.313,0.177 10 true <F> 2.479,2.573 2.76,2.729 0.281,0.156 10 true <F> 4.333,2.719 4.635,2.885 0.302,0.167 10 true <E> 4.708,2.604 5.021,2.771 0.313,0.167 10 true <G> 5.542,2.615 5.833,2.771 0.292,0.156 10 true <G> 0.448,2.26 0.74,2.438 0.292,0.177 10 true <F> 1.729,1.052 2.042,1.24 0.313,0.188 10 true <F> 4.594,0.583 4.885,0.76 0.292,0.177 10 true <F>
*a Airbag Connector *b Airbag Bolt



b.

Remove the bolt <H> and disengage the guide to separate the ground bracket.


c.

Remove the 2 bolts <G>.


d.

Disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Refer to How to Connect or Disconnect Airbag Connector:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR



e.

Remove the 4 clips.


f.

Disengage the hooks.


g.

Remove the 5 bolts <F>, screw <E> and nut <I> as shown in the illustration.


h.

Disengage the guides to remove the instrument panel sub-assembly as shown in the illustration.

B587165C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)



Hide 55950G 46.REMOVE DEFROSTER NOZZLE ASSEMBLY (for Separate Type)

a.
B587166E01
0.063,1.177 0.354,1.354 0.292,0.177 10 true <A> 1.313,1.417 1.604,1.594 0.292,0.177 10 true <A> 3.073,1.406 3.365,1.583 0.292,0.177 10 true <A>

Remove the 3 screws <A>.


b.

Disengage the guides to remove the defroster nozzle assembly.


Hide 89120A 47.REMOVE AUTOMATIC LIGHT CONTROL SENSOR (for Separate Type)

Hide 55328 48.REMOVE NO. 1 INSTRUMENT PANEL PIN (for Separate Type)

HINT:

Use the same procedure as for the opposite side.


a.

Remove the screw <A>.


b.
B587167E01
1.115,0.594 1.417,0.771 0.302,0.177 10 true <A>

Disengage the guide to remove the No. 1 instrument panel pin.