Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for Gasoline Model LHD) › 2020.07–2020.09
RM36W0E _54 Brake _088656 BRAKE SYSTEM (OTHER) _0432271 BRAKE BOOSTER(for Gasoline Model LHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for Gasoline Model LHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during brake booster assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking Assist Monitor System (Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 47201 1.REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY

Hide 3.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17701 4.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 51451A 6.REMOVE CENTER ENGINE UNDER COVER (for M15A-FKS)

Hide 55225C 7.REMOVE DASH PANEL HEAT INSULATOR (for M15A-FKS)

a.
C436788

Remove the 3 nuts and dash panel heat insulator.


Hide 44773F 8.DISCONNECT UNION TO CHECK VALVE HOSE (for M15A-FKS)

a.
C436789

Slide the clip and disconnect the union to check valve hose from the brake booster assembly.


Hide 44772 9.DISCONNECT CHECK VALVE TO CONNECTOR TUBE HOSE (for 1KR-FE)

a.
C436790

Slide the clip and disconnect the check valve to connector tube hose from the brake booster assembly.


b.

Remove the 2 nuts to separate the vacuum hose assembly from the vehicle.


Hide 55606 10.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 45259A 11.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45260 12.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 13.LOOSEN CLEVIS LOCK NUT

a.
C142634C01
1.948,1.146 1.75,1.667 1.75,1.667 1.5,1.667 false 2.365,1.135 2.781,1.135 true 1.323,1.604 1.635,1.76 0.313,0.156 10 *1 2.833,1.073 3.146,1.229 0.313,0.156 10 *2
*1 Lock Nut
*2 Brake Master Cylinder Push Rod Clevis


Loosen the lock nut of the brake master cylinder push rod clevis.


Hide 47101A 14.REMOVE BRAKE PEDAL RETURN SPRING

Hide 44610 16.REMOVE BRAKE BOOSTER ASSEMBLY

a.
C439862

Remove the bolt to separate the engine room main wire.


b.

Disengage the clamp.


c.

w/ Vacuum Warning Switch:

i.
C436792

Disconnect the vacuum warning switch connector.



d.

w/ Vacuum Sensor:

i.
C436791

Disconnect the vacuum sensor connector.



e.
C436793C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the vehicle body as shown in the illustration.


f.
C436794

Disengage the 5 clamps to separate the brake lines from the No. 1 brake tube clamp.


g.
C436795

Disengage the clamp and remove the No. 1 brake tube clamp from the vehicle body.


h.
C436796

Disengage the 5 clamps to remove the No. 2 brake tube clamp from the brake lines.


i.
C436797

Using a union nut wrench, disconnect the 2 brake lines from the brake actuator assembly.


j.
C436798

Remove the 4 nuts.


k.

Remove the brake master cylinder push rod clevis and lock nut from the brake booster assembly.


l.

Remove the brake booster assembly from the vehicle body.

NOTICE:

Do not apply excessive force to the brake lines.



Hide 44785 17.REMOVE BRAKE BOOSTER GASKET

a.

Remove the brake booster gasket from the brake booster assembly.