The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the air conditioner unit assembly removal/installation are shown below.
1.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
for HFC-134a(R134a):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>REPLACEMENT
for HFO-1234yf(R1234yf):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFO-1234yf(R1234yf))>REPLACEMENT
51451A
2.REMOVE CENTER ENGINE UNDER COVER (for Full Cover Type)
3.DRAIN ENGINE COOLANT
for M15A-FKS:
for M15A-FXE:
Click hereGeneral>MAINTENANCE>M15A-FXE COOLANT (for Engine)>REPLACEMENT
for 1KR-FE:
4.REMOVE WINDSHIELD WIPER MOTOR AND LINK
55735A
5.REMOVE WATER GUARD PLATE LH
Disengage the claws to remove the water guard plate LH.
55815E
6.REMOVE NO. 1 FRONT VENTILATOR SEAL
Disengage the claws to remove the No. 1 front ventilator seal.
55701J
7.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY
Disengage the clamp.
for Cold Area Specification Vehicles:
Disengage the clamps.
Disconnect the connector.
Remove the 12 bolts and outer cowl top panel sub-assembly.
88707
8.DISCONNECT SUCTION PIPE SUB-ASSEMBLY (except 1KR-FE)
88716A
9.DISCONNECT COOLER REFRIGERANT LIQUID PIPE A (except 1KR-FE)
88710G
10.DISCONNECT NO. 2 AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY (for 1KR-FE)
16290F
11.DISCONNECT NO. 3 WATER BY-PASS HOSE ASSEMBLY
87245
12.DISCONNECT INLET HEATER WATER HOSE
13.REMOVE INSTRUMENT PANEL ASSEMBLY
87211
14.REMOVE NO. 1 AIR DUCT
Remove the 2 bolts.
Disengage the claws to remove the No. 1 air duct.
15.REMOVE STEERING COLUMN ASSEMBLY
55086A
16.REMOVE CENTER HEATER TO REGISTER DUCT SUB-ASSEMBLY
Remove the clip.
Disengage the clamp to remove the center heater to register duct sub-assembly.
55084E
17.REMOVE NO. 1 HEATER TO REGISTER DUCT SUB-ASSEMBLY
Remove the clip.
Disengage the clamp to remove the No. 1 heater to register duct sub-assembly.
55085
18.REMOVE NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY
Remove the clip.
Disengage the clamp to remove the No. 2 heater to register duct sub-assembly.
19.REMOVE FRONT SEAT ASSEMBLY LH
20.REMOVE FRONT SEAT ASSEMBLY RH
Use the same procedure as for the LH side.
58569D
21.REMOVE FRONT FLOOR CAUTION PLATE COVER (for Cold Area Specification Vehicles)
Disengage the claw and guide to remove the front floor caution plate cover.
77306
22.REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY (for Cold Area Specification Vehicles)
23.REMOVE NO. 5 REAR AIR DUCT (for Cold Area Specification Vehicles)
24.REMOVE NO. 3 REAR AIR DUCT (for Cold Area Specification Vehicles)
58510D
25.SEPARATE FRONT FLOOR CARPET ASSEMBLY (for Cold Area Specification Vehicles)
Remove the 2 clips to turn back the front floor carpet assembly as shown in the illustration.
26.REMOVE NO. 4 REAR AIR DUCT (for Cold Area Specification Vehicles)
27.REMOVE NO. 2 REAR AIR DUCT (for Cold Area Specification Vehicles)
28.REMOVE NO. 1 REAR AIR DUCT (for Cold Area Specification Vehicles)
58510D
29.SEPARATE FRONT FLOOR CARPET ASSEMBLY (except Cold Area Specification Vehicles)
Remove the 2 clips to turn back the front floor carpet assembly as shown in the illustration.
55216C
30.REMOVE NO. 4 DASH PANEL INSULATOR PAD
Disengage the clips to remove the No. 4 dash panel insulator pad.
88539J
31.DISCONNECT DRAIN COOLER HOSE
Disconnect the drain cooler hose.
83108
32.REMOVE METER MIRROR SUB-ASSEMBLY (w/ Headup Display)
55308B
33.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY (for TFTM Made)
Remove the bolt and nut, No. 3 instrument panel to cowl brace sub-assembly.
34.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MULTIPLEX NETWORK BODY ECU
35.REMOVE TELEMATICS TRANSCEIVER WITH BRACKET (w/ Telematics Transceiver)
55306A
36.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
| *A | for Cold Area Specification Vehicles |
Remove the bolt to disconnect the wire harness.
Disengage the clamps to disconnect the wire harness.
for Cold Area Specification Vehicles:
Remove the ground wire bolt.
Disengage the guide to disconnect the ground wire.
Remove the bolt, screw, nut and No.1 instrument panel brace sub-assembly.
82141
37.SEPARATE INSTRUMENT PANEL WIRE
Disengage the clamps.
Remove the 2 nuts to separate the instrument panel junction block assembly RH.
for Manual Air Conditioning System Single Layer Type:
Disconnect the 2 connectors.
Disengage the clamp.
for Manual Air Conditioning System Double Layer Type:
Disconnect the 3 connectors.
Disengage the clamps.
for Automatic Air Conditioning System:
Disconnect the connector.
Disengage the clamp.
for Manual Air Conditioning System:
Disconnect the connector.
Disengage the clamp.
for Automatic Air Conditioning System:
Disconnect the 2 connectors.
Disengage the clamp.
Disconnect each connector.
| *A | for Cold Area Specification Vehicles | - | - |
| *a | Guide | *b | Clamp |
for Cold Area Specification Vehicles:
Disconnect the connector.
Remove the 4 ground wire bolts.
Disengage the guides to disconnect the 4 ground wires.
Disengage each clamp to separate the instrument panel wire.
38.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY
Remove the nut and 6 bolts.
Disengage the guides to remove the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.
39.REMOVE AIR CONDITIONER UNIT ASSEMBLY
Remove the 3 bolts and air conditioner unit assembly.