Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made) › 2020.07–2021.11
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0432441 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF Made)  C13807E  Stop Lamp Relay Actuator Stuck On  


DESCRIPTION

When any of the following conditions are met, the skid control ECU (brake actuator assembly) sets the drive output (STPO) ON which operates the stop light control relay (stop light switch assembly) and turns on the stop lights.

Illumination Conditions:
·

Pre-collision brake is operating.*

·

The dynamic radar cruise control system is operating and is applying the brakes.*

·

Secondary collision brake is operating.


*: w/ Pre-collision System


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C13807E Stop Lamp Relay Actuator Stuck On
·

STP terminal is ON and STP2 terminal is OFF for 5 seconds or more.

·

ACC terminal and STP terminal are OFF, and STP2 terminal is ON for 5 seconds or more.


·

Wire harness or connector

·

Stop light switch assembly

·

Skid control ECU (brake actuator assembly)

·

Rear combination light assembly LH

·

Rear combination light assembly RH

·

Center stop light assembly


Brake

WIRING DIAGRAM

C427243E10
1.333,0.698 2.74,0.927 1.406,0.229 10 false from IGP Relay 1.313,1.563 2.74,1.813 1.427,0.25 10 false from Auxiliary Battery 2.542,1.135 3.458,1.385 0.917,0.25 10 false to Each ECU 1.625,2.302 1.781,2.5 0.156,0.198 10 false 7 3.333,2.302 3.49,2.5 0.156,0.198 10 false 3 4.719,2.323 4.958,2.521 0.24,0.198 10 false 2 4.938,2.427 5.552,2.625 0.615,0.198 10 false STP 4.938,3.333 5.552,3.531 0.615,0.198 10 false STPO 4.938,4.323 5.552,4.521 0.615,0.198 10 false STP2 4.677,3.219 4.917,3.417 0.24,0.198 10 false 28 4.667,4.208 4.896,4.396 0.229,0.188 10 false 12 3.333,3.219 3.49,3.417 0.156,0.198 10 false 4 3.333,4.198 3.49,4.396 0.156,0.198 10 false 1 1.625,3.219 1.781,3.417 0.156,0.198 10 false 6 1.625,4.198 1.781,4.396 0.156,0.198 10 false 2 3.104,2.427 3.26,2.625 0.156,0.198 10 false L 2.906,3.344 3.323,3.521 0.417,0.177 10 false ACC 2.938,4.344 3.354,4.531 0.417,0.188 10 false OUT 1.844,2.417 2,2.615 0.156,0.198 10 false B 1.865,3.333 2.021,3.531 0.156,0.198 10 false B 1.854,4.333 2.281,4.531 0.427,0.198 10 false GND 0.979,2.563 1.594,2.76 0.615,0.198 10 false STOP 0.635,3.5 2.469,3.698 1.833,0.198 10 false ECU-IGP NO. 3 1.667,4.813 2.125,5.01 0.458,0.198 10 false A63 1.667,4.99 3.542,5.26 1.875,0.271 10 false Stop Light Switch Assembly 4.74,4.813 5.198,5.01 0.458,0.198 10 false A37 4.729,4.99 6.26,5.49 1.531,0.5 10 false Skid Control ECU (Brake Actuator Assembly) 1.625,5.865 1.781,6.063 0.156,0.198 10 false 1 2.958,5.865 3.115,6.063 0.156,0.198 10 false 3 1.833,5.865 1.99,6.063 0.156,0.198 10 false E 2.76,5.865 2.917,6.063 0.156,0.198 10 false B 1.635,6.385 2.021,6.563 0.385,0.177 10 false O103 1.635,6.552 3.073,6.948 1.438,0.396 10 false Rear Combination Light Assembly LH 1.635,7.344 1.792,7.542 0.156,0.198 10 false 1 2.958,7.344 3.115,7.542 0.156,0.198 10 false 3 4.969,7.344 5.125,7.542 0.156,0.198 10 false 1 6.302,7.344 6.458,7.542 0.156,0.198 10 false 2 1.615,7.875 1.99,8.063 0.375,0.188 10 false O104 1.604,8.052 3.042,8.469 1.438,0.417 10 false Rear Combination Light Assembly RH 1.833,7.344 1.99,7.542 0.156,0.198 10 false E 2.76,7.344 2.917,7.542 0.156,0.198 10 false B 5.177,7.344 5.333,7.542 0.156,0.198 10 false B 6.104,7.344 6.26,7.542 0.156,0.198 10 false E 4.823,7.875 5.104,8.052 0.281,0.177 10 false X2 4.823,8.042 6.563,8.333 1.74,0.292 10 false Center Stop Light Assembly 0.167,0.146 2.156,0.344 1.99,0.198 12 false for Halogen Headlight:

C427243E11
1.333,0.698 2.74,0.927 1.406,0.229 10 false from IGP Relay 1.313,1.563 2.74,1.813 1.427,0.25 10 false from Auxiliary Battery 2.49,1.135 3.74,1.365 1.25,0.229 10 false to Each ECU 1.625,2.302 1.781,2.5 0.156,0.198 10 false 7 3.333,2.302 3.49,2.5 0.156,0.198 10 false 3 4.708,2.323 4.958,2.51 0.25,0.188 10 false 2 4.938,2.427 5.552,2.625 0.615,0.198 10 false STP 4.938,3.333 5.552,3.531 0.615,0.198 10 false STPO 4.938,4.323 5.552,4.521 0.615,0.198 10 false STP2 4.667,3.219 4.896,3.406 0.229,0.188 10 false 28 4.656,4.208 4.885,4.396 0.229,0.188 10 false 12 3.333,3.219 3.49,3.417 0.156,0.198 10 false 4 3.333,4.198 3.49,4.396 0.156,0.198 10 false 1 1.625,3.219 1.781,3.417 0.156,0.198 10 false 6 1.625,4.198 1.781,4.396 0.156,0.198 10 false 2 3.104,2.427 3.26,2.625 0.156,0.198 10 false L 2.906,3.344 3.323,3.521 0.417,0.177 10 false ACC 2.938,4.344 3.354,4.531 0.417,0.188 10 false OUT 1.844,2.417 2,2.615 0.156,0.198 10 false B 1.865,3.333 2.021,3.531 0.156,0.198 10 false B 1.854,4.333 2.281,4.531 0.427,0.198 10 false GND 0.979,2.563 1.594,2.76 0.615,0.198 10 false STOP 0.635,3.5 2.469,3.698 1.833,0.198 10 false ECU-IGP NO. 3 1.667,4.813 2.125,5.01 0.458,0.198 10 false A63 1.667,4.99 3.542,5.26 1.875,0.271 10 false Stop Light Switch Assembly 4.74,4.813 5.198,5.01 0.458,0.198 10 false A37 4.729,4.99 6.26,5.49 1.531,0.5 10 false Skid Control ECU (Brake Actuator Assembly) 1.625,5.865 1.781,6.063 0.156,0.198 10 false 1 2.958,5.865 3.115,6.063 0.156,0.198 10 false 3 1.833,5.865 1.99,6.063 0.156,0.198 10 false E 2.76,5.865 2.917,6.063 0.156,0.198 10 false B 1.635,6.385 2.021,6.563 0.385,0.177 10 false O109 1.635,6.552 3.073,6.948 1.438,0.396 10 false Rear Combination Light Assembly LH 1.635,7.344 1.792,7.542 0.156,0.198 10 false 1 2.958,7.344 3.115,7.542 0.156,0.198 10 false 3 4.969,7.344 5.125,7.542 0.156,0.198 10 false 1 6.302,7.344 6.458,7.542 0.156,0.198 10 false 2 1.615,7.875 1.99,8.063 0.375,0.188 10 false O110 1.604,8.052 3.042,8.469 1.438,0.417 10 false Rear Combination Light Assembly RH 1.833,7.344 1.99,7.542 0.156,0.198 10 false E 2.76,7.344 2.917,7.542 0.156,0.198 10 false B 5.177,7.344 5.333,7.542 0.156,0.198 10 false B 6.104,7.344 6.26,7.542 0.156,0.198 10 false E 4.823,7.875 5.104,8.052 0.281,0.177 10 false X2 4.823,8.042 6.563,8.333 1.74,0.292 10 false Center Stop Light Assembly 0.167,0.146 2.156,0.344 1.99,0.198 12 false for LED Headlight:

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the skid control ECU (brake actuator assembly), perform yaw rate and acceleration sensor zero point calibration and store system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>UTILITY



HINT:

When DTC P057111 and/or P057112 are output together with DTC C13807E, inspect and repair the trouble areas indicated by DTC P057111 and/or P057112 first.


PROCEDURE

1.CHECK STOP LIGHT ILLUMINATION STATUS
a.

With the brake pedal released, check the illumination status of the brake lights.


Result:
Result Proceed to
The stop lights are illuminated. A
The stop lights are not illuminated. B



A

2.CHECK BRAKE ACTUATOR ASSEMBLY

B

5.CHECK BRAKE ACTUATOR ASSEMBLY
2.CHECK BRAKE ACTUATOR ASSEMBLY

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A37 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A37-2 (STP) - Body ground Stop light switch assembly off
(Brake pedal released)
Below 1.5 V



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

NG

3.CHECK STOP LIGHT SWITCH ASSEMBLY
3.CHECK STOP LIGHT SWITCH ASSEMBLY

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A63 stop light switch assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A37-2 (STP) - Body ground Always Below 1.5 V



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

4.CHECK FOR SHORT TO +B IN STP CIRCUIT
4.CHECK FOR SHORT TO +B IN STP CIRCUIT
a.

Check that there is no short to +B in the STP circuit (wire harnesses, connectors and stop lights and ECUs).

OK:

No short to +B.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE MALFUNCTIONING PART

5.CHECK BRAKE ACTUATOR ASSEMBLY

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A37 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A37-12 (STP2) - Body ground Stop light switch assembly on
(Brake pedal depressed)
11 to 14 V



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

NG

6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

Pre-procedure1

a.
C401043C98
0.448,0.448 0.781,0.698 0.333,0.25 2.292,1.781 1.885,1.052 true 0.188,0.177 0.5,0.333 0.313,0.156 10 false *a 0.5,0.49 0.958,0.688 0.458,0.198 10 false A63 2.333,1.813 2.792,2.01 0.458,0.198 10 false L
*a Component with harness connected
(Stop Light Switch Assembly)


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A63-3 (L) - Body ground Stop light switch assembly on
(Brake pedal depressed)
11 to 14 V



Post-procedure1

c.

None


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

7.CHECK FOR SHORT TO GROUND IN STP2 CIRCUIT
7.CHECK FOR SHORT TO GROUND IN STP2 CIRCUIT
a.

Check that there is no short to ground in the STP2 circuit (wire harnesses, connectors and ECUs).

OK:

There is no short to ground.



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE MALFUNCTIONING PART