Home › Suspension › REAR SUSPENSION › REAR SHOCK ABSORBER › 2020.07–2020.09
RM36W0E _53 Suspension _087264 REAR SUSPENSION _0417605 REAR SHOCK ABSORBER A

REAR SUSPENSION  REAR SHOCK ABSORBER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the rear shock absorber assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Rear wheel alignment adjustment for HV Model:
1.

Perform "Reset Memory"

2.

Perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for TMC Made:
(Click here)
for TMMF Made:
(Click here)
for Gasoline Model:
Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for TMC Made:
(Click here)
for TMMF Made:
(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 64715C 2.REMOVE DECK SIDE TRIM COVER

a.
C429097

Disengage the 3 claws and 2 guides, and remove the deck side trim cover.


Hide 48597A 3.REMOVE REAR SHOCK ABSORBER CUSHION RETAINER

a.
C437641C02
0.802,1.5 1.135,1.5 false 1.135,1.969 1.469,1.969 false 0.625,1.406 0.938,1.563 0.313,0.156 10 false *a 0.927,1.885 1.24,2.042 0.313,0.156 10 false *b
*a Wooden Block
*b Jack


Support the spring seat of the rear axle beam assembly using a jack and wooden block.

CAUTION:

Do not jack up the rear axle beam assembly too high as the vehicle may fall.


NOTICE:
·

When jacking up the rear axle beam assembly, be sure to jack it up slowly.

·

Make sure to perform this operation with the vehicle kept as low as possible.

·

Keep supporting the rear axle beam assembly with a jack until the installation of the rear shock absorber assembly is completed.




b.

for Double Nut Type:

i.
C484094C01
0.719,1.875 1.031,2.073 0.313,0.198 10 true *a 2.865,1.552 3.177,1.75 0.313,0.198 10 true *b
*a Turn
*b Hold


Using a 5 mm hexagon socket wrench, secure the rear shock absorber assembly rod and remove the nut (upper nut) using a wrench.



c.

Using a 5 mm hexagon socket wrench, secure the rear shock absorber assembly rod and remove the nut using a wrench.


d.
C433942

Remove the rear shock absorber cushion retainer.


Hide 48755 4.REMOVE REAR SUSPENSION SUPPORT

a.

Remove the rear suspension support from the rear shock absorber assembly.


Hide 48540 5.REMOVE REAR SHOCK ABSORBER ASSEMBLY

a.
C427911C01
1.448,1.5 1.781,1.5 false 1.823,1.969 2.156,1.969 false 1.281,1.406 1.594,1.563 0.313,0.156 10 false *a 1.656,1.885 1.969,2.042 0.313,0.156 10 false *b
*a Wooden Block
*b Jack


Remove the bolt while keeping the nut from rotating and remove the rear shock absorber assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



Hide 48760B 6.REMOVE REAR SUSPENSION SUPPORT ASSEMBLY

a.

Remove the rear suspension support assembly from the rear shock absorber assembly.