Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made) › 2020.07–2021.11
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0432441 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF Made)  C051218  Right Rear Wheel Speed Sensor Circuit Current Below Threshold  


DESCRIPTION

Each speed sensor detects wheel speed and sends signals to the skid control ECU (brake actuator assembly). These signals are used by the ABS control.

The speed sensor detects the magnetic fields of the speed sensor rotor as it rotates and outputs a pulse signal.

The frequency of the pulse varies in accordance with the rotational speed of the speed sensor rotor and the system uses this to determine the wheel speed.

HINT:

The following example shows a pulse signal that is output when the wire harness connectors are connected to the speed sensors and skid control ECU (brake actuator assembly).

C151818E70
1.594,0.854 1.594,0.469 1.594,0.469 1.688,0.469 false 1.74,0.385 2.656,0.625 0.917,0.24 10 false Speed Sensor 4.021,2.115 4.719,2.365 0.698,0.25 10 false Low speed 4.99,2.115 5.729,2.354 0.74,0.24 10 false High speed 0.969,2.177 2.25,2.406 1.281,0.229 10 false Speed Sensor Rotor


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C051218 Right Rear Wheel Speed Sensor Circuit Current Below Threshold This wheel speed sensor signal electrical current value is less than the threshold value for 0.14 second or more.
·

Rear speed sensor RH (rear axle hub and bearing assembly RH)

·

Wire harness and connector

·

Skid control ECU (brake actuator assembly)


Brake

WIRING DIAGRAM

C393355E77
0.573,2.219 2.01,2.802 1.438,0.583 10 false Rear Speed Sensor RH (Rear Axle Hub and Bearing Assembly RH) 2.365,2.208 3.51,2.729 1.146,0.521 10 false Skid Control Sensor Wire RH 5.167,3.167 6.76,3.802 1.594,0.635 10 false Skid Control ECU (Brake Actuator Assembly) 5.25,1.031 5.75,1.271 0.5,0.24 10 false RR+ 3.219,1.125 3.667,1.385 0.448,0.26 10 false RR+ 1.615,1.125 2.031,1.365 0.417,0.24 10 false RR+ 2.438,1.125 2.927,1.375 0.49,0.25 10 false RR+ 1.615,1.833 2.01,2.073 0.396,0.24 10 false RR- 2.438,1.833 2.917,2.01 0.479,0.177 10 false RR- 3.24,1.833 3.698,2.021 0.458,0.188 10 false RR- 5.25,1.708 5.75,1.917 0.5,0.208 10 false RR- 2.083,1.104 2.635,1.344 0.552,0.24 10 false i2 2.083,1.802 2.417,2.052 0.333,0.25 10 false i2 3.635,1.115 4.125,1.333 0.49,0.219 10 false iO1 3.635,1.802 4.052,2.104 0.417,0.302 10 false iO1 2.094,1.615 2.396,1.844 0.302,0.229 10 false 2 5.167,3 5.667,3.198 0.5,0.198 10 false A37 2.104,0.917 2.406,1.146 0.302,0.229 10 false 1 3.698,0.917 4,1.146 0.302,0.229 10 false 1 3.698,1.615 4,1.844 0.302,0.229 10 false 2 5.01,1.031 5.302,1.271 0.292,0.24 10 false 34 5,1.698 5.354,1.948 0.354,0.25 10 false 33

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake actuator assembly), perform yaw rate and acceleration sensor zero point calibration and system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>UTILITY

·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>TEST MODE PROCEDURE



HINT:

The rear speed sensor RH is incorporated into the rear axle hub and bearing assembly RH.

If the rear speed sensor RH needs to be replaced, replace the rear axle hub and bearing assembly RH.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the i2 rear speed sensor RH (rear axle hub and bearing assembly RH) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Pre-procedure2

d.

Turn the ignition switch to ON.


Procedure1

e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
i2-1 (RR+) - i2-2 (RR-) Ignition switch ON 11 to 14 V



Post-procedure1

f.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

2.INSPECT SKID CONTROL SENSOR WIRE RH

NG

4.INSPECT SKID CONTROL SENSOR WIRE RH
2.INSPECT SKID CONTROL SENSOR WIRE RH

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the iO1 skid control sensor wire RH connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
i2-2 (RR-) or iO1-1 (RR-) - Body ground and other terminals Always 10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE RH - BRAKE ACTUATOR ASSEMBLY)

NG

REPLACE SKID CONTROL SENSOR WIRE RH

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE RH - BRAKE ACTUATOR ASSEMBLY)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A37 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
iO1-2 (RR-) or A37-33 (RR-) - Body ground Always 10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT SKID CONTROL SENSOR WIRE RH

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the iO1 skid control sensor wire RH connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
i2-1 (RR-) - iO1-2 (RR-) Always Below 1 Ω



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE RH - BRAKE ACTUATOR ASSEMBLY)

NG

REPLACE SKID CONTROL SENSOR WIRE RH

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE RH - BRAKE ACTUATOR ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
iO1-2 (RR-) - A37-33 (RR-) Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

6.READ VALUE USING GTS (RR WHEEL SPEED)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.READ VALUE USING GTS (RR WHEEL SPEED)

Pre-procedure1

a.

Reconnect the A37 skid control ECU (brake actuator assembly) connector.


b.

Reconnect the iO1 skid control sensor wire RH connector.


c.

Reconnect the i2 rear speed sensor RH (rear axle hub and bearing assembly RH) connector.


Procedure1

d.

Operate the GTS to check the Data List.

Chassis > Brake
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear speed sensor RH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake > Data List
Tester Display
RR Wheel Speed
50003 435 15

e.

Drive the vehicle and perform a road test.

OK:

The values change in accordance with the operation of the vehicle.


NOTICE:

Perform the above inspection before removing the sensor and connector.



Post-procedure1

f.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

NG

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH