This DTC is stored when the blind spot monitor sensor RH (A) detects an open in the outer rear view mirror indicator RH.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1AB513 | Outer Mirror Indicator (Module "A" Side) Circuit Open | Both of the following conditions are met:
·
The blind spot monitor system is on ·
The current flowing to the indicator is below a specified value when indicator operation voltage is being sent to the indicator |
·
Outer mirror RH (outer rear view mirror indicator RH) ·
Outer rear view mirror assembly RH ·
Harness or connector ·
Blind spot monitor sensor RH (A) |
for TMC Made
for TMMF Made
When checking for DTCs, make sure that the blind spot monitor system is turned on.
Turn the ignition switch off.
Turn the ignition switch to ON.
Recheck for DTCs and check if the same DTC is output again.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Check the vehicle specifications.
| Result | Proceed to |
|---|---|
| for TMC Made | A |
| for TMMF Made | B |
A
B
Disconnect the S6 blind spot monitor sensor RH (A) connector.
Disconnect the K8 outer rear view mirror assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S6-4 (OMIR) - K8-8 (BSR+) | Always | Below 1 Ω |
| K8-15 (-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A outer mirror RH (outer rear view mirror indicator RH) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K8-8 (BSR+) - A-2 (+) | Always | Below 1 Ω |
| K8-15 (-) - A-1 (-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the O37 blind spot monitor sensor RH (A) connector.
Disconnect the K14 outer rear view mirror assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O37-4 (OMIR) - K14-1 (BSR+) | Always | Below 1 Ω |
| K14-11 (-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C outer mirror RH (outer rear view mirror indicator RH) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K14-1 (BSR+) - C-2 (+) | Always | Below 1 Ω |
| K14-11 (-) - C-1 (-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG