Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2020.07–2020.09
RM36W0E _57 Power Source / Network _088060 NETWORKING _0420500 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B120687  P/W Master SW System Missing Message  B124987  Double Locking System Missing Message  B232187  D-Door P/W System Missing Message  B232287  P-Door P/W System Missing Message  B232387  RR-Door P/W System Missing Message  B232487  RL-Door P/W System Missing Message  


DESCRIPTION

This DTC is stored when LIN communication between the main body ECU (multiplex network body ECU) and multiplex network master switch assembly, power window regulator motor assembly (driver door), power window regulator motor assembly (front passenger door), power window regulator motor assembly (rear door RH), power window regulator motor assembly (rear door LH) or double lock door control relay assembly*1 stops for 10 seconds or more.

*1: w/ Double Locking System


DTC No. Detection Item DTC Detection Condition Trouble Area
B120687 P/W Master SW System Missing Message No communication between multiplex network master switch assembly and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Main body ECU (multiplex network body ECU)

·

Power distribution box assembly

·

Multiplex network master switch assembly

·

Wire harness or connector


B124987 Double Locking System Missing Message No communication between double lock door control relay assembly and main body ECU (multiplex network body ECU) for 10 seconds or more.*1
·

Main body ECU (multiplex network body ECU)

·

Power distribution box assembly

·

Double lock door control relay assembly

·

Wire harness or connector


B232187 D-Door P/W System Missing Message No communication between front power window regulator motor assembly RH and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Main body ECU (multiplex network body ECU)

·

Power distribution box assembly

·

Multiplex network master switch assembly

·

Front power window regulator motor assembly (driver door)

·

Wire harness or connector


B232287 P-Door P/W System Missing Message No communication between front power window regulator motor assembly LH and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Main body ECU (multiplex network body ECU)

·

Power distribution box assembly

·

Front power window regulator motor assembly (front passenger door)

·

Wire harness or connector


B232387 RR-Door P/W System Missing Message No communication between rear power window regulator motor assembly RH and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Main body ECU (multiplex network body ECU)

·

Power distribution box assembly

·

Front power window regulator motor assembly (rear RH door)

·

Wire harness or connector


B232487 RL-Door P/W System Missing Message No communication between rear power window regulator motor assembly LH and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Main body ECU (multiplex network body ECU)

·

Power distribution box assembly

·

Front power window regulator motor assembly (rear LH door)

·

Wire harness or connector



*1: w/ Double Locking System


WIRING DIAGRAM

C434540E02
0.146,0.083 0.854,0.292 0.708,0.208 12 false for RHD: 1.063,1.042 1.438,1.229 0.375,0.188 10 false LIN2 0.229,2.323 1.385,2.865 1.156,0.542 10 false Main Body ECU (Multiplex Network Body ECU) 1.438,2.25 2.844,2.74 1.406,0.49 10 false Power Distribution Box Assembly 1.5,3.24 2.875,3.458 1.375,0.219 10 false from Auxiliary Battery 0.51,4.135 1.406,4.313 0.896,0.177 10 false DOOR DBL/L 0.406,4.604 1.479,4.792 1.073,0.188 10 false ECU-DCC NO. 2 1.583,4.021 1.844,4.188 0.26,0.167 10 false +B 1.573,4.469 2.031,4.667 0.458,0.198 10 false CPUB 2.354,4.448 2.813,4.646 0.458,0.198 10 false MPX1 1.573,4.906 2.031,5.104 0.458,0.198 10 false GND 1.406,5.385 3,5.792 1.594,0.406 10 false Double Lock Door Control Relay Assembly *1 0.177,9.156 2.073,9.375 1.896,0.219 10 false *1: w/ Double Locking System 0.604,9.521 2.5,9.74 1.896,0.219 10 false : LIN Communication Line 4.396,0.208 5.771,0.427 1.375,0.219 10 false from Auxiliary Battery 4.604,1.042 4.979,1.229 0.375,0.188 10 false LIN1 4.594,1.417 4.969,1.604 0.375,0.188 10 false LIN2 5.594,1.031 5.771,1.208 0.177,0.177 10 false B 5.417,1.396 5.792,1.583 0.375,0.188 10 false GND 6.021,1.188 6.927,1.385 0.906,0.198 10 false ECU-B NO. 2 4.354,1.875 5.948,2.25 1.594,0.375 10 false Multiplex Network Master Switch Assembly 6.083,2.833 6.865,3.021 0.781,0.188 10 false DOOR F/R 4.583,2.896 4.958,3.083 0.375,0.188 10 false LIN 5.625,2.698 6,2.885 0.375,0.188 10 false B 5.438,3.042 5.813,3.229 0.375,0.188 10 false GND 4.208,3.573 6.125,3.969 1.917,0.396 10 false Front Power Window Regulator Motor Assembly (Driver Door) 4.594,4.542 4.969,4.729 0.375,0.188 10 false LIN 5.615,4.365 5.792,4.552 0.177,0.188 10 false B 5.438,4.708 5.813,4.896 0.375,0.188 10 false GND 6.104,4.5 6.885,4.688 0.781,0.188 10 false DOOR F/L 4.042,5.208 6.333,5.583 2.292,0.375 10 false Front Power Window Regulator Motor Assembly (Front Passenger Door) 4.594,6.198 4.969,6.385 0.375,0.188 10 false LIN 5.635,6.01 5.813,6.198 0.177,0.188 10 false B 5.438,6.365 5.813,6.552 0.375,0.188 10 false GND 6.083,6.156 6.865,6.344 0.781,0.188 10 false DOOR R/R 4.167,6.844 6.438,7.229 2.271,0.385 10 false Rear Power Window Regulator Motor Assembly (Rear RH Door) 4.594,7.865 4.969,8.052 0.375,0.188 10 false LIN 5.646,7.688 5.823,7.875 0.177,0.188 10 false B 5.448,8.042 5.823,8.229 0.375,0.188 10 false GND 6.094,7.833 6.875,8.021 0.781,0.188 10 false DOOR R/L 4.198,8.573 6.469,8.958 2.271,0.385 10 false Rear Power Window Regulator Motor Assembly (Rear LH Door) 1.531,0.865 1.729,1.042 0.198,0.177 10 false 15 1.5,1.052 1.75,1.229 0.25,0.177 10 false MB 2.698,0.844 2.896,1.021 0.198,0.177 10 false 17 2.698,1.042 2.948,1.219 0.25,0.177 10 false 4E 2.719,1.375 2.917,1.552 0.198,0.177 10 false 37 2.698,1.563 2.948,1.74 0.25,0.177 10 false 4B 4.354,0.875 4.552,1.052 0.198,0.177 10 false 17 4.354,1.26 4.552,1.438 0.198,0.177 10 false 16 5.813,0.948 6.01,1.125 0.198,0.177 10 false 11 5.813,1.302 6.01,1.479 0.198,0.177 10 false 12 4.365,1.708 4.74,1.896 0.375,0.188 10 false K5 4.396,2.74 4.594,2.917 0.198,0.177 10 false 9 4.219,3.365 4.594,3.552 0.375,0.188 10 false K7 5.813,2.604 6.01,2.781 0.198,0.177 10 false 2 5.833,2.958 6.031,3.135 0.198,0.177 10 false 1 4.417,4.385 4.615,4.563 0.198,0.177 10 false 9 5.833,4.26 6.031,4.438 0.198,0.177 10 false 2 5.823,4.604 6.021,4.781 0.198,0.177 10 false 1 4.063,5.031 4.438,5.219 0.375,0.188 10 false L7 4.417,6.042 4.615,6.219 0.198,0.177 10 false 9 5.833,5.896 6.031,6.073 0.198,0.177 10 false 2 5.833,6.281 6.031,6.458 0.198,0.177 10 false 1 4.167,6.677 4.542,6.865 0.375,0.188 10 false M4 4.396,7.708 4.594,7.885 0.198,0.177 10 false 9 5.833,7.583 6.031,7.76 0.198,0.177 10 false 2 5.823,7.938 6.021,8.115 0.198,0.177 10 false 1 4.208,8.375 4.583,8.563 0.375,0.188 10 false N4 1.333,3.885 1.531,4.063 0.198,0.177 10 false 12 1.323,4.344 1.521,4.521 0.198,0.177 10 false 11 1.417,4.792 1.615,4.969 0.198,0.177 10 false 7 2.823,4.302 3.021,4.479 0.198,0.177 10 false 9 1.417,5.198 1.76,5.365 0.344,0.167 10 false H42

C434541E03
0.198,0.125 0.948,0.344 0.75,0.219 12 false for LHD: 1.083,1.031 1.458,1.219 0.375,0.188 10 false LIN2 1.51,0.854 1.75,1.021 0.24,0.167 10 false 15 0.208,2.344 1.375,2.885 1.167,0.542 10 false Main Body ECU (Multiplex Network Body ECU) 1.51,2.25 2.927,2.698 1.417,0.448 10 false Power Distribution Box Assembly 4.583,1.052 4.958,1.24 0.375,0.188 10 false LIN1 4.583,1.396 4.958,1.583 0.375,0.188 10 false LIN2 5.417,1.396 5.865,1.594 0.448,0.198 10 false GND 5.615,1.021 5.802,1.188 0.188,0.167 10 false B 4.365,1.927 5.948,2.313 1.583,0.385 10 false Multiplex Network Master Switch Assembly 5.99,1.177 6.885,1.375 0.896,0.198 10 false ECU-B NO. 2 4.417,0.208 5.792,0.417 1.375,0.208 10 false from Auxiliary Battery 4.594,2.896 4.969,3.083 0.375,0.188 10 false LIN 5.625,2.698 5.813,2.865 0.188,0.167 10 false B 5.448,3.073 5.802,3.271 0.354,0.198 10 false GND 6.073,2.844 6.823,3.052 0.75,0.208 10 false DOOR F/L 4.219,3.594 6.135,3.969 1.917,0.375 10 false Front Power Window Regulator Motor Assembly (Driver Door) 4.604,4.542 4.979,4.729 0.375,0.188 10 false LIN 5.625,4.365 5.813,4.531 0.188,0.167 10 false B 5.438,4.729 5.792,4.927 0.354,0.198 10 false GND 6.104,4.5 6.854,4.708 0.75,0.208 10 false DOOR F/R 4.073,5.229 6.365,5.615 2.292,0.385 10 false Front Power Window Regulator Motor Assembly (Front Passenger Door) 4.594,6.188 4.969,6.375 0.375,0.188 10 false LIN 5.646,5.99 5.833,6.156 0.188,0.167 10 false B 5.438,6.365 5.792,6.563 0.354,0.198 10 false GND 6.104,6.156 6.854,6.365 0.75,0.208 10 false DOOR R/R 4.094,6.906 6.385,7.292 2.292,0.385 10 false Rear Power Window Regulator Motor Assembly (Rear RH Door) 4.583,7.854 4.958,8.042 0.375,0.188 10 false LIN 5.625,7.688 5.813,7.854 0.188,0.167 10 false B 5.438,8.042 5.792,8.24 0.354,0.198 10 false GND 6.115,7.833 6.823,8.021 0.708,0.188 10 false DOOR R/L 4.104,8.552 6.396,8.938 2.292,0.385 10 false Rear Power Window Regulator Motor Assembly (Rear LH Door) 0.625,9.521 2.281,9.719 1.656,0.198 10 false : LIN Communication Line 1.49,1.042 1.729,1.208 0.24,0.167 10 false MB 2.75,0.844 2.99,1.01 0.24,0.167 10 false 17 2.74,1.042 2.979,1.208 0.24,0.167 10 false 4E 4.344,0.896 4.583,1.063 0.24,0.167 10 false 17 4.333,1.25 4.573,1.417 0.24,0.167 10 false 16 5.823,0.948 6.063,1.115 0.24,0.167 10 false 11 5.823,1.302 6.063,1.469 0.24,0.167 10 false 12 4.365,1.74 4.656,1.906 0.292,0.167 10 false L13 4.417,2.729 4.656,2.896 0.24,0.167 10 false 9 5.833,2.594 6.073,2.76 0.24,0.167 10 false 2 5.844,2.958 6.083,3.125 0.24,0.167 10 false 1 4.219,3.406 4.594,3.594 0.375,0.188 10 false L7 4.406,4.396 4.646,4.563 0.24,0.167 10 false 9 5.844,4.26 6.083,4.427 0.24,0.167 10 false 2 5.823,4.604 6.063,4.771 0.24,0.167 10 false 1 4.083,5.042 4.458,5.229 0.375,0.188 10 false K7 4.427,6.01 4.667,6.177 0.24,0.167 10 false 9 5.844,5.927 6.083,6.094 0.24,0.167 10 false 2 5.823,6.26 6.063,6.427 0.24,0.167 10 false 1 4.094,6.698 4.469,6.885 0.375,0.188 10 false M4 4.417,7.698 4.656,7.865 0.24,0.167 10 false 9 5.854,7.594 6.094,7.76 0.24,0.167 10 false 2 5.844,7.927 6.083,8.094 0.24,0.167 10 false 1 4.094,8.385 4.469,8.573 0.375,0.188 10 false N4

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When a power window regulator motor assembly is replaced or removed and reinstalled, it is necessary to perform initialization.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

Result:
Proceed to
NEXT



NEXT

2.CHECK VEHICLE TYPE
2.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for RHD A
for LHD B



A

3.CHECK FOR DTC

B

21.CHECK FOR DTC
3.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
DTC is B232588 output A
DTC B120687, B124987*1, B232187, B232287, B232387 and B232487 are output B
DTC B120687, B232187, B232287, B232387 and B232487 are output C
DTC B120687 and B232187 are output D
Only DTC B120687 is output E
Only DTC B124987 is output F
Only DTC B232187 is output G
Only DTC B232287 is output H
Only DTC B232387 is output I
Only DTC B232487 is output J
DTC is not output K


*1: Double Locking System



A

B

4.INSPECT POWER DISTRIBUTION BOX ASSEMBLY

C

5.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)

D

7.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)

E

8.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)

F

9.INSPECT POWER DISTRIBUTION BOX ASSEMBLY

G

12.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR))

H

15.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR))

I

17.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR))

J

19.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR))

K

4.INSPECT POWER DISTRIBUTION BOX ASSEMBLY
a.

Remove the power distribution box assembly.


C433197C03
1.875,0.333 2.292,0.583 0.417,0.25 5.5,0.083 5.917,0.333 0.417,0.25 2.042,0.927 2.24,1.385 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *a 1.958,0.375 2.271,0.531 0.313,0.156 10 false MB 5.615,0.125 5.927,0.281 0.313,0.156 10 false 4E 2.281,1.344 2.698,1.521 0.417,0.177 10 false LIN2
*a Component without harness connected
(Power Distribution Box Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

This inspection is to check the LIN communication line in the power distribution box assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
4E-17 - MB-15 (LIN2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)
a.

Disconnect the 4E power distribution box assembly connector.


b.

Disconnect the K5 multiplex network master switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Condition Specified Condition
4E-17 - K5-17 (LIN1) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.INSPECT POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT POWER DISTRIBUTION BOX ASSEMBLY
a.

Remove the power distribution box assembly.


C433197C03
1.875,0.333 2.292,0.583 0.417,0.25 5.5,0.083 5.917,0.333 0.417,0.25 2.042,0.927 2.24,1.385 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *a 1.958,0.375 2.271,0.531 0.313,0.156 10 false MB 5.615,0.125 5.927,0.281 0.313,0.156 10 false 4E 2.281,1.344 2.698,1.521 0.417,0.177 10 false LIN2
*a Component without harness connected
(Power Distribution Box Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

This inspection is to check the LIN communication line in the power distribution box assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
4E-17 - MB-15 (LIN2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

7.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)
a.

Disconnect the 4E power distribution box assembly connector.


b.

Disconnect the K5 multiplex network master switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
4E-17 - K5-17 (LIN1) Ignition switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the K5 multiplex network master switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K5-11 (B) - K5-12 (GND) Ignition switch off 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K5-12 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT POWER DISTRIBUTION BOX ASSEMBLY
a.

Remove the power distribution box assembly.


B514061C13
1.875,0.333 2.292,0.583 0.417,0.25 5.5,0.083 5.917,0.333 0.417,0.25 2.156,1.354 2.042,0.938 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *a 1.958,0.375 2.271,0.531 0.313,0.156 10 false MB 5.615,0.125 5.927,0.313 0.313,0.188 10 false 4B 2.042,1.385 2.458,1.563 0.417,0.177 10 false LIN2
*a Component without harness connected
(Power Distribution Box Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

This inspection is to check the LIN communication line in the power distribution box assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
4B-37 - MB-15 (LIN2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY)

NG

10.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY)
a.

Disconnect the 4B power distribution box assembly connector.


b.

Disconnect the H42 double lock door control relay assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
4B-37 - H42-9 (MPX1) Ignition switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the H42 multiplex network master switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H42-12 (+B) - H42-7 (GND) Ignition switch off 11 to 14 V
H42-11 (CPUB) - H42-7 (GND)



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H42-7 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR))
a.

Disconnect the 4E power distribution box assembly connector.


b.

Disconnect the K7 front power window regulator motor assembly (driver door) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4E-17 - K7-9 (LIN) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR) - AUXILIARY BATTERY AND BODY GROUND)

NG

14.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR))
13.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR) - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the K7 front power window regulator motor assembly (driver door) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K7-2 (B) - K7-1 (GND) Ignition switch off 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K7-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR))
a.

Disconnect the K5 multiplex network master switch assembly connector.


b.

Disconnect the K7 front power window regulator motor assembly (driver door) connector.


c.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Condition Specified Condition
4E-17 - K7-9 (LIN) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR))
a.

Disconnect the 4E power distribution box assembly connector.


b.

Disconnect the L7 front power window regulator motor assembly (front passenger door) connector.


c.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
4E-17 - L7-9 (LIN) Ignition switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR) - AUXILIARY BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR) - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the L7 front power window regulator motor assembly (front passenger door) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L7-2 (B) - L7-1 (GND) Ignition switch off 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L7-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR))
a.

Disconnect the 4E power distribution box assembly connector.


b.

Disconnect the M4 rear power window regulator motor assembly (rear RH door) connector.


c.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
4E-17 - M4-9 (LIN) Ignition switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR) - AUXILIARY BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR) - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the M4 rear power window regulator motor assembly (rear RH door) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M4-2 (B) - M4-1 (GND) Ignition switch off 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M4-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR))
a.

Disconnect the 4E power distribution box assembly connector.


b.

Disconnect the N4 rear power window regulator motor assembly (rear LH door) connector.


c.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
4E-17 - N4-9 (LIN) Ignition switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

20.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR) - AUXILIARY BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR) - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the N4 rear power window regulator motor assembly (rear LH door) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N4-2 (B) - N4-1 (GND) Ignition switch off 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N4-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
DTC is B232588 output A
DTC B120687, B232187, B232287, B232387 and B232487 are output B
DTC B120687 and B232187 are output C
Only DTC B120687 is output D
Only DTC B232187 is output E
Only DTC B232287 is output F
Only DTC B232387 is output G
Only DTC B232487 is output H
DTC is not output I



A

B

22.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)

C

24.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)

D

25.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)

E

26.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR))

F

29.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR))

G

31.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR))

H

33.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR))

I

22.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)
a.

Disconnect the 4E power distribution box assembly connector.


b.

Disconnect the L13 multiplex network master switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Condition Specified Condition
4E-17 - L13-17 (LIN1) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

23.INSPECT POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.INSPECT POWER DISTRIBUTION BOX ASSEMBLY
a.

Remove the power distribution box assembly.


C433197C04
1.875,0.333 2.292,0.583 0.417,0.25 5.5,0.083 5.917,0.333 0.417,0.25 2.031,0.927 2.229,1.385 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *a 1.948,0.365 2.26,0.521 0.313,0.156 10 false MB 5.615,0.125 5.927,0.281 0.313,0.156 10 false 4E 2.271,1.323 2.688,1.5 0.417,0.177 10 false LIN2
*a Component without harness connected
(Power Distribution Box Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

This inspection is to check the LIN communication line in the power distribution box assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
4E-17 - MB-15 (LIN2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

24.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)
a.

Disconnect the 4E power distribution box assembly connector.


b.

Disconnect the L13 multiplex network master switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
4E-17 - L13-17 (LIN1) Ignition switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

25.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the L13 multiplex network master switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L13-11 (B) - L13-12 (GND) Ignition switch off 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L13-12 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

26.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR))
a.

Disconnect the 4E power distribution box assembly connector.


b.

Disconnect the L7 front power window regulator motor assembly (driver door) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4E-17 - L7-9 (LIN) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

27.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR) - AUXILIARY BATTERY AND BODY GROUND)

NG

28.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR))
27.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR) - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the L7 front power window regulator motor assembly (driver door) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L7-2 (B) - L7-1 (GND) Ignition switch off 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L7-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

28.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR))
a.

Disconnect the L13 multiplex network master switch assembly connector.


b.

Disconnect the L7 front power window regulator motor assembly (driver door) connector.


c.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Condition Specified Condition
4E-17 - L7-9 (LIN) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

29.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR))
a.

Disconnect the 4E power distribution box assembly connector.


b.

Disconnect the K7 front power window regulator motor assembly (front passenger door) connector.


c.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
4E-17 - K7-9 (LIN) Ignition switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

30.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR) - AUXILIARY BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

30.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR) - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the K7 front power window regulator motor assembly (front passenger door) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K7-2 (B) - K7-1 (GND) Ignition switch off 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K7-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

31.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR))
a.

Disconnect the 4E power distribution box assembly connector.


b.

Disconnect the M4 rear power window regulator motor assembly (rear RH door) connector.


c.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
4E-17 - M4-9 (LIN) Ignition switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

32.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR) - AUXILIARY BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

32.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR) - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the M4 rear power window regulator motor assembly (rear RH door) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M4-2 (B) - M4-1 (GND) Ignition switch off 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M4-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

33.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR))
a.

Disconnect the 4E power distribution box assembly connector.


b.

Disconnect the N4 rear power window regulator motor assembly (rear LH door) connector.


c.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
4E-17 - N4-9 (LIN) Ignition switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

34.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR) - AUXILIARY BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

34.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR) - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the N4 rear power window regulator motor assembly (rear LH door) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N4-2 (B) - N4-1 (GND) Ignition switch off 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N4-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR