Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made) › 2020.07–2021.11
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0435240 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMMF Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMMF Made)  C051D54  Multi-axis Acceleration Sensor Module "A" Missing Calibration  


DESCRIPTION

The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition.

The skid control ECU (brake actuator assembly) receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via CAN communication.

HINT:

If a communication error with the yaw rate and acceleration sensor (airbag sensor assembly) is detected, DTCs U012587 and U015187 are stored.


The DTC is also stored when the calibration has not been completed.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C051D54 Multi-axis Acceleration Sensor Module "A" Missing Calibration Zero point calibration of acceleration sensor undone.
·

Acceleration sensor (airbag sensor assembly) installation

·

Acceleration sensor (airbag sensor assembly)

·

Skid control ECU (brake actuator assembly)


Brake

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and store system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made)>UTILITY

·

After replacing or reinstalling the yaw rate and acceleration sensor (airbag sensor assembly), perform acceleration sensor zero point calibration and store system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made)>UTILITY



PROCEDURE

1.PERFORM ACCELERATION SENSOR ZERO POINT CALIBRATION
a.

Clear the zero point calibration data and system information.

Chassis > Brake > Utility
Tester Display
Reset Memory
50005 435 4560

b.

Perform acceleration sensor zero point calibration and store system information memorization.

Chassis > Brake > Utility
Tester Display
Calibration
50005 435 4554

Result:
Proceed to
NEXT



NEXT

2.CLEAR DTC
2.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake Booster > Clear DTCs
50002 466

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

3.RECONFIRM DTC
3.RECONFIRM DTC
a.

Read the DTCs using the GTS.

Chassis > Brake > Trouble Codes
50001 435

b.

Check if the same DTC is output.


Result:
Result Proceed to
C051D54 is not output A
C051D54 is output B



A

END

B

4.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
4.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
a.

Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION

OK:

The yaw rate and acceleration sensor (airbag sensor assembly) is tightened to the specified torque.

The yaw rate and acceleration sensor (airbag sensor assembly) is not installed in a tilted position.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (LATERAL G, FORWARD AND REARWARD G)

NG

5.READ VALUE USING GTS (LATERAL G, FORWARD AND REARWARD G)
a.

Check the Data List using the GTS.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Lateral G Lateral G Min.: -25.105 m/s2, Max.: 24.908 m/s2 Turning right: -25.105 to 0.000 m/s2
Turning left: 0.000 to 24.908 m/s2
During turning: Changes in proportion with lateral acceleration
Forward and Rearward G Forward and rearward G Min.: -25.105 m/s2, Max.: 24.908 m/s2 During deceleration: -25.105 to 0.000 m/s2
During acceleration: 0.000 to 24.908 m/s2
During acceleration/deceleration: Changes in proportion with acceleration
Chassis > Brake > Data List
Tester Display
Lateral G
Forward and Rearward G
50003 435 25,26

b.

Check the acceleration sensor (airbag sensor assembly) output value displayed on the GTS.

OK:

The acceleration sensor (airbag sensor assembly) output value is normal.



Result:
Proceed to
OK
NG



OK

NG