Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made) › 2020.07–2021.11
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0435240 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMMF Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMMF Made)  P057111  Brake Switch "A" Circuit Short to Ground  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives stop light switch assembly signals and uses them to determine whether or not the brakes are applied.

When the brake pedal is depressed and no signal is received from the stop light switch assembly, this DTC is output.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
P057111 Brake Switch "A" Circuit Short to Ground Either of the following is detected when the vehicle speed of 3 km/h (2 mph) or more:
1.

With the stop light switch assembly off, the stop light switch assembly is judged to be on based on the master cylinder pressure value for 3 seconds or more.

2.

With the stop light switch assembly off, the master cylinder pressure is more than 8 MPa (81.6 kgf/cm2, 1160 psi) for 3 seconds or more.


·

Stop light switch assembly

·

Wire harness or connector

·

Skid control ECU (brake actuator assembly)


Brake

WIRING DIAGRAM

C444150E03
1.646,6.677 3.406,6.938 1.76,0.26 10 false Stop Light Switch Assembly 4.625,6.854 5.083,7.052 0.458,0.198 10 false A39 4.677,4.01 4.99,4.208 0.313,0.198 10 false 41 4.917,4.01 5.375,4.208 0.458,0.198 10 false STP 4.927,4.896 5.385,5.094 0.458,0.198 10 false STPO 4.927,5.917 5.385,6.115 0.458,0.198 10 false STP2 4.677,4.927 4.99,5.125 0.313,0.198 10 false 33 4.677,5.927 4.99,6.125 0.313,0.198 10 false 43 3.344,5.927 3.656,6.125 0.313,0.198 10 false 1 3.344,4.927 3.656,5.125 0.313,0.198 10 false 4 3.344,4.021 3.656,4.219 0.313,0.198 10 false 3 2.948,5.906 3.406,6.104 0.458,0.198 10 false OUT 2.927,4.896 3.385,5.094 0.458,0.198 10 false ACC 3.115,3.99 3.573,4.188 0.458,0.198 10 false L 1.75,4.354 2.208,4.552 0.458,0.198 10 false B 1.74,5.917 2.198,6.115 0.458,0.198 10 false GND 1,4.583 1.458,4.781 0.458,0.198 10 false STOP 1.156,3.531 2.75,3.792 1.594,0.26 10 false from Auxiliary Battery 2.104,7.302 3.344,7.583 1.24,0.281 10 false to Stop Light Circuit 1.552,5.938 1.865,6.135 0.313,0.198 10 false 2 1.552,4.365 1.865,4.563 0.313,0.198 10 false 7 1.646,6.51 2.104,6.708 0.458,0.198 10 false A63 4.625,7.01 6.75,7.448 2.125,0.438 10 false Skid Control ECU (Brake Actuator Assembly) 1.354,2.646 1.688,2.979 0.333,0.333 10 false A68 1.375,2.823 3.146,3.073 1.771,0.25 10 false Hybrid Vehicle Control ECU 4.885,2.823 6.698,3.375 1.813,0.552 10 false Certification ECU (Smart Key ECU Assembly)*3 2.271,2.344 2.729,2.542 0.458,0.198 10 false STP 5.25,2.333 5.708,2.531 0.458,0.198 10 false STP1 4.99,0.76 5.302,0.958 0.313,0.198 10 false 21 5.26,0.906 5.719,1.104 0.458,0.198 10 false STP 4.656,1.479 7.01,1.875 2.354,0.396 10 false Electric Brake Booster (Brake Booster with Master Cylinder Assembly) 4.646,1.292 5.958,1.51 1.313,0.219 10 false A34*1, A35*2 0.417,8.25 1.75,8.542 1.333,0.292 10 false *1: for LHD 2.656,2.24 3.031,2.479 0.375,0.24 10 false 6 1.677,8.25 3.5,8.563 1.823,0.313 10 false *2: for RHD 4.99,2.24 5.302,2.438 0.313,0.198 10 false 21 4.875,2.667 5.302,2.875 0.427,0.208 10 false H45 2.813,8.26 5.75,8.604 2.938,0.344 10 false *3: w/ Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and store system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made)>UTILITY



PROCEDURE

1.READ VALUE USING GTS (MASTER CYLINDER SENSOR)
a.

Check the Data List using the GTS.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Master Cylinder Sensor 1 Master cylinder pressure sensor pressure (value detected by ECU) Min.: -1.00 MPa, Max.: 23.99 MPa Brake pedal released: -1.00 to 0.00 MPa Reading increases when brake pedal is depressed
Chassis > Brake > Data List
Tester Display
Master Cylinder Sensor 1
50003 435 21

b.

Check the value of Data List item Master Cylinder Sensor 1 when the brake pedal is released.

OK:

The value of Data List item Master Cylinder Sensor 1 when the brake pedal is released is less than 0.15 MPa.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY SIGNAL INPUT CIRCUIT)

NG

4.CHECK DTC
2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY SIGNAL INPUT CIRCUIT)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-41 (STP) - Body ground Brake pedal depressed 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the A63 stop light switch assembly connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A63-3 (L) - A39-41 (STP) Always Below 1 Ω
A63-3 (L) or A39-41 (STP) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK DTC
a.

Read the DTCs using the GTS.

Chassis > Brake > Trouble Codes
50001 435

b.

Check the details of the DTCs.


Result:
Result Proceed to
P057111 and C05401C, C054028 and/or C054049 are output simultaneously A
P057111 is output B



A

B

GO TO BRAKE SYSTEM

Refer to "Brake drag" of problem symptoms table.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE SYSTEM (for HV Model TMMF Made)>PROBLEM SYMPTOMS TABLE