Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made) › 2020.07–2021.11
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0435240 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMMF Made) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMMF Made)  Brake Warning Light Remains ON  


DESCRIPTION

This procedure is for troubleshooting when the brake warning light / red (malfunction) remains on but no DTCs are output.

The skid control ECU (brake actuator assembly) controls the brake warning light / red (malfunction) in the combination meter assembly via CAN communication.

WIRING DIAGRAM

C444367E02
0.802,0.708 1.417,0.906 0.615,0.198 10 false CANL 0.771,1.177 1.385,1.375 0.615,0.198 10 false CANH 1.292,0.542 1.604,0.74 0.313,0.198 10 false 25 1.302,1 1.615,1.198 0.313,0.198 10 false 9 5.031,0.531 5.344,0.729 0.313,0.198 10 false 19 5.083,1 5.396,1.198 0.313,0.198 10 false 5 5.042,1.677 5.354,1.875 0.313,0.198 10 false 36 5.344,1.802 5.802,2 0.458,0.198 10 false IGR 3.771,1.948 5.76,2.146 1.99,0.198 10 false ECU-IGR NO. 3 1.677,1.771 4.74,1.969 3.063,0.198 10 false from IGR-NO. 1 Relay 5.094,2.625 5.406,2.823 0.313,0.198 10 false 4 5.344,2.75 5.802,2.948 0.458,0.198 10 false LBL 3.146,2.625 3.604,2.823 0.458,0.198 10 false E 4.396,2.625 4.854,2.823 0.458,0.198 10 false + 4.635,2.625 4.792,2.823 0.156,0.198 10 false 1 2.917,2.625 3.073,2.823 0.156,0.198 10 false 2 2.604,3.271 3.094,3.51 0.49,0.24 10 false A102 2.594,3.427 5.104,4.406 2.51,0.979 10 false Brake Fluid Level Warning Switch (Brake Booster with Master Cylinder Assembly) 5.333,4.24 5.948,4.438 0.615,0.198 10 false GND1 5.323,4.635 5.938,4.833 0.615,0.198 10 false GND2 5.042,4.125 5.354,4.323 0.313,0.198 10 false 46 5.031,4.521 5.344,4.719 0.313,0.198 10 false 14 5.292,5.313 5.75,5.51 0.458,0.198 10 false A39 5.281,5.49 6.844,5.875 1.563,0.385 10 false Skid Control ECU (Brake Actuator Assembly) 2.385,6.083 6.052,6.281 3.667,0.198 10 false : CAN Communication Line 0.094,5.469 4.073,5.667 3.979,0.198 10 false Combination Meter Assembly 0.094,5.302 0.552,5.5 0.458,0.198 10 false H6 5.333,0.719 5.948,0.917 0.615,0.198 10 false CANL 5.333,1.198 5.948,1.396 0.615,0.198 10 false CANH

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and store system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made)>UTILITY

·

Before performing this procedure, depress the brake pedal and confirm that the stop lights illuminate.



PROCEDURE

1.PRE-CHECK
a.

Check that all of the following conditions required for the brake warning light / red (malfunction) to turn off are met:

i.

The ABS warning light is not illuminated.

HINT:

If the ABS warning light remains illuminated, make sure that the conditions required for the ABS warning light to turn off are met.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made)>ABS Warning Light Remains ON



ii.

The brake fluid level in the brake master cylinder reservoir assembly is not low.


iii.

The vacuum inside the brake booster decreases.

HINT:

When the vacuum inside the brake booster decreases, the brake warning light / red (malfunction) comes on.




Result:
Proceed to
NEXT



NEXT

2.CHECK VEHICLE CONTROL HISTORY (ELECTRONICALLY CONTROLLED BRAKE SYSTEM AND ELECTRIC PARKING BRAKE SYSTEM)
2.CHECK VEHICLE CONTROL HISTORY (ELECTRONICALLY CONTROLLED BRAKE SYSTEM AND ELECTRIC PARKING BRAKE SYSTEM)
a.

Using the GTS, check for Vehicle Control History (RoB).

Chassis > Brake > Utility
Tester Display
Vehicle Control History (RoB)
50005 435 55
HINT:

If vehicle control history is stored when the electronically controlled brake system and electric parking brake system are suspended, the brake warning light / red (malfunction) illuminates.



Result:
Result Proceed to
There is no vehicle control history for when the electronically controlled brake system was suspended. (for Type A) A
There is vehicle control history for when the electronically controlled brake system was suspended. B



A

3.INSPECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

B

PERFORM TROUBLESHOOTING AND REPAIR REGARDING VEHICLE CONTROL HISTORY

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made)>VEHICLE CONTROL HISTORY

NOTICE:

After performing troubleshooting and repair regarding vehicle control history, clear the vehicle control history.



3.INSPECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY
a.
C304973C08
2.385,2.74 2.042,1.813 true 1.104,2.74 1.427,1.833 true 0.271,0.25 0.583,0.448 0.313,0.198 10 false *a 1.031,2.802 1.344,3 0.313,0.198 10 false E 2.365,2.802 2.677,3 0.313,0.198 10 false +
*a Component without harness connected
(Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A102 brake fluid level warning switch (brake master cylinder reservoir assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

HINT:

A float is located inside the reservoir. Its position changes according to the brake fluid level.


Standard Resistance:
Tester Connection Condition Specified Condition
1 (+) - 2 (E) Switch off (float up) 1.9 to 2.1 kΩ
1 (+) - 2 (E) Switch on (float down) Below 1 Ω



e.

If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the A102 brake fluid level warning switch (brake master cylinder reservoir assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A39-4 (LBL) - A102-1 (+) Always Below 1 Ω
A39-4 (LBL) or A102-1 (+) - Body ground Always 10 kΩ or higher
A102-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT COMBINATION METER ASSEMBLY
a.

Perform the Active Test of the combination meter assembly using the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display
Brake Warning
50004 409 107

b.

Check the combination meter assembly.

OK:

The brake warning light / red (malfunction) turns on or off in accordance with GTS operation.



Result:
Proceed to
OK
NG



OK

NG