Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made) › from 2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0440900 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made)  C125600  Accumulator Low Pressure Abnormality  


DESCRIPTION

The accumulator pressure sensor is built into the brake actuator (brake booster with master cylinder assembly) and detects the accumulator pressure.

The skid control ECU (brake booster with master cylinder assembly) turns on the brake system warning light (red indicator) and brake system warning light (yellow indicator), and sounds the meter buzzer if it senses a decrease in the accumulator pressure.

DTC C125600 may be stored if the accumulator pressure drops due to frequent braking (this is not a malfunction).

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C125600 Accumulator Low Pressure Abnormality Significant drop in accumulator pressure continues.
(DTCs will be stored and the buzzer will operate when either condition is met.)
·

Accumulator pressure dropped due to frequent brake pedal operation (not a malfunction)

·

Pump motor malfunction

·

Accumulator deterioration

·

Accumulator pressure sensor (brake booster with master cylinder assembly)

·

Supply voltage reduced


Brake

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>UTILITY

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK DTC
a.

Check if the same DTC is output.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
Only C125600 is output A
None of the above conditions are met B



A

2.INSPECT BRAKE BOOSTER PUMP ASSEMBLY

B

2.INSPECT BRAKE BOOSTER PUMP ASSEMBLY
a.
C345125C24
0.698,1.333 1.448,1.656 true 1.99,1.604 2.74,1.302 true 2.01,2.125 2.719,2.656 true 0.729,2.625 1.427,2.135 true 0.208,0.198 0.521,0.396 0.313,0.198 10 false *a 0.385,1.229 0.698,1.427 0.313,0.198 10 false BM1 0.323,2.563 0.75,2.792 0.427,0.229 10 false GND1 2.75,2.594 3.188,2.854 0.438,0.26 10 false GND2 2.792,1.188 3.188,1.406 0.396,0.219 10 false BM2
*a Component without harness connected
(Brake Booster Pump Assembly)


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the A30 brake booster pump assembly connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (BM1) - 4 (GND1) Always 10 Ω or less
1 (BM2) - 3 (GND2) Always 10 Ω or less
2 (BM1) - 1 (BM2) Always Below 1 Ω
4 (GND1) - 3 (GND2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (ACCUMULATOR PRESSURE)

NG

REPLACE BRAKE BOOSTER PUMP ASSEMBLY

3.READ VALUE USING GTS (ACCUMULATOR PRESSURE)
a.

Reconnect the A30 brake booster pump assembly connector.


b.

Disconnect the A27 brake pedal stroke sensor assembly connector.


c.

Select the Data List on the GTS.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
MTT Pump motor operation status OFF / ON OFF: Pump motor off
ON: Pump motor on
-
Accumulator Pressure Accumulator pressure output value Min.: 0.00 MPa, Max.: 24.48 MPa 15.00 to 21.00 MPa
(Pressure stable and pump motor stopped)
When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator
Chassis > Brake > Data List
Tester Display
MTT
Accumulator Pressure
50003 435 100,212

d.

Depress the brake pedal several times to operate the pump motor, then wait until it stops.


e.

After the pump motor stops, wait for 30 seconds, then check the drop in the accumulator pressure sensor output value and the state of the pump motor.


Result:
Result Proceed to
30 seconds after the pump motor stops the drop in the value of Accumulator Pressure after the pump motor stops is less than 2.50 MPa and pump motor does not operate within 30 seconds A
30 seconds after the pump motor stops the drop in the value of Accumulator Pressure is 2.50 MPa or more or pump motor operates within 30 seconds B



A

B

4.READ VALUE USING GTS (SERVO PRESSURE)
4.READ VALUE USING GTS (SERVO PRESSURE)
a.

Turn the ignition switch off.


b.

Reconnect the A27 brake pedal stroke sensor assembly connector.


c.

Select the Active Test on the GTS.

Chassis > Brake > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
ECB Solenoid (SLR) Linear solenoid reduction valve (SLR) Solenoid ON/OFF ECB: Electronically Controlled Brake System
Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Servo Pressure Pressure value of servo Min.: 0.00 MPa, Max.: 24.48 MPa Brake pedal released: 0.00 to 2.10 MPa Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal
Chassis > Brake > Active Test
Active Test Display
ECB Solenoid (SLR)
Data List Display
Servo Pressure
50004 435 42 210

d.

Perform the Active Test and operate the linear solenoid (SLR) in the brake actuator (brake booster with master cylinder assembly).


e.

Check that the servo pressure output value does not increase when performing the Active Test.

OK:

The servo pressure output value does not increase when performing the Active Test.


HINT:

If the servo pressure output value increases, an internal brake fluid leak in the brake actuator (brake booster with master cylinder assembly) is suspected.



Result:
Result Proceed to
The servo pressure output value increases. A
The servo pressure output value does not increase. B



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY AND BRAKE BOOSTER PUMP ASSEMBLY

for Brake Booster with Master Cylinder Assembly: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for HV Model TMC Made RHD)>REMOVAL

for Brake Booster Pump Assembly: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER PUMP>REMOVAL