Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made) › 2020.07–2020.09
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0440901 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made)  C054017  Brake Pressure Sensor "A" Circuit Voltage Above Threshold  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C054017 Brake Pressure Sensor "A" Circuit Voltage Above Threshold When vehicle speed exceeds 3 km/h (2 mph) and stop light switch assembly is OFF, master cylinder pressure continuously exceeds 1.764 MPa (18.0 kgf/cm2, 255 psi) for 5 seconds or more.
·

Wire harness and connector

·

Stop light switch assembly

·

Master cylinder pressure sensor (Brake actuator assembly)

·

Master cylinder pressure sensor circuit malfunction

·

Skid control ECU (Brake actuator assembly)


Brake

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>CALIBRATION



PROCEDURE

1.CLEAR DTC
a.

Operate the GTS to clear the codes.

Chassis > Brake > Clear DTCs
50002 435

b.

Press the DTC clear button.


c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

2.RECONFIRM DTC
2.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

b.

Operate the GTS to read the DTCs.

Chassis > Brake > Trouble Codes
50001 435

c.

Check if the same DTC is output.


Post-procedure1

d.

None


Result:
Result Proceed to
Only C054017 is output A
C054017 and P057113 are output B
None of the above conditions are met C



A

3.READ VALUE USING GTS (STOP LIGHT SW)

B

GO TO DTC CHART (P057113)

C

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

3.READ VALUE USING GTS (STOP LIGHT SW)
a.

Operate the GTS to check the Data List.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly
(STP terminal input)
OFF / ON OFF: Brake pedal released
ON: Brake pedal depressed
HINT:

The brake pedal state is determined using the voltage at terminal STP


Chassis > Brake > Data List
Tester Display
Stop Light SW
50003 435 59

b.

Check that the stop light switch assembly condition observed on the GTS changes according to brake pedal operation.

OK:

The GTS displays OFF / ON according to brake pedal operation.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (MASTER CYLINDER SENSOR 1)

NG

7.CHECK STOP LIGHT SWITCH ASSEMBLY INSTALLATION
4.READ VALUE USING GTS (MASTER CYLINDER SENSOR 1)
a.

Operate the GTS to check the Data List.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Master Cylinder Sensor 1 Master cylinder pressure sensor pressure (value detected by ECU) Min.: -1.00 MPa
Max.: 23.99 MPa
Brake pedal released: -1.00 to 0.00 MPa Reading increases when brake pedal is depressed
Chassis > Brake > Data List
Tester Display
Master Cylinder Sensor 1
50003 435 21

b.

Start the engine.


c.

Check the value of Data List item Master Cylinder Sensor 1 when the brake pedal is released.

OK:

The value of Data List item Master Cylinder 1 is within standard range.



Result:
Proceed to
OK
NG



OK

5.CLEAR DTC

NG

5.CLEAR DTC
a.

Operate the GTS to clear the codes.

Chassis > Brake > Clear DTCs
50002 435

b.

Press the DTC clear button.


c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

6.RECONFIRM DTC
6.RECONFIRM DTC

Pre-procedure1

a.

Start the engine.


b.

Drive the vehicle and perform a braking test (decelerate the vehicle by depressing the brake pedal).


Procedure1

c.

Operate the GTS to read the DTCs.

Chassis > Brake > Trouble Codes
50001 435

d.

Check if the same DTC is output.


Post-procedure1

e.

None


Result:
Result Proceed to
C054017 is not output A
C054017 is output B



A

B

7.CHECK STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.


b.

Check the stop light switch assembly installation.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION

OK:

The stop light switch assembly installation are normal.



Result:
Proceed to
OK
NG



OK

8.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

INSTALL STOP LIGHT SWITCH ASSEMBLY CORRECTLY

8.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION

OK:

The stop light switch assembly is normal.



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A36 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A36-35 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 8 to 14 V
A36-35 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR