The power window regulator motor assemblies are operated by the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assemblies*1. The power window regulator motor assemblies have motor, regulator and ECU functions.
This DTC is stored when the ECU built into a power window regulator motor assembly and multiplex network master switch assembly determine that the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly*1 is stuck.
*1: w/ Rear Power Window
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from |
|---|---|---|---|---|
| B2312 | Power Window Switch Malfunction | ·
Multiplex network master switch assembly stuck ·
Multiplex network master switch assembly held in same position for more than 20 seconds ·
Multiplex network master switch assembly operated for 20 seconds or more |
Multiplex network master switch assembly | Master Switch |
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from |
|---|---|---|---|---|
| B2312 | Power Window Switch Malfunction | ·
Multiplex network master switch assembly stuck ·
Multiplex network master switch assembly held in same position for more than 20 seconds |
·
Multiplex network master switch assembly ·
Power window regulator motor assembly (for driver door) ·
Wire harness or connector |
D-Door Motor |
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from |
|---|---|---|---|---|
| B2312 | Power Window Switch Malfunction | ·
Power window regulator switch assembly stuck ·
Power window regulator switch assembly held in same position for more than 20 seconds |
·
Power window regulator switch assembly ·
Power window regulator motor assembly (for front passenger door) ·
Wire harness or connector |
P-Door Motor |
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from |
|---|---|---|---|---|
| B2312 | Power Window Switch Malfunction | ·
Rear power window regulator switch assembly (for LH door) stuck ·
Rear power window regulator switch assembly (for LH door) held in same position for more than 20 seconds |
·
Rear power window regulator switch assembly (for LH door) ·
Power window regulator motor assembly (for rear LH door) ·
Wire harness or connector |
RL-Door Motor |
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from |
|---|---|---|---|---|
| B2312 | Power Window Switch Malfunction | ·
Rear power window regulator switch assembly (for RH door) stuck ·
Rear power window regulator switch assembly (for RH door) held in same position for more than 20 seconds |
·
Rear power window regulator switch assembly (for RH door) ·
Power window regulator motor assembly (for rear RH door) ·
Wire harness or connector |
RR-Door Motor |
Refer to DTC B2311.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>B2311
DTC B2312 is stored in the multiplex network master switch assembly and in each power window regulator motor assembly.
If a power window regulator motor assembly has been replaced with a new one, initialize the power window control system.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION
Inspect the fuses for circuits related to this system before performing the following procedure.
The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
If DTC B2312 is not output again after the DTC has been cleared, the DTC was stored due to the switch being held in the same position continuously.
Check the vehicle specifications.
| Result | Proceed to |
|---|---|
| for LHD without Rear Power Window | A |
| for RHD without Rear Power Window | B |
| for LHD with Rear Power Window | C |
| for RHD with Rear Power Window | D |
A
B
C
D
Check for DTCs.
| Result | Proceed to |
|---|---|
| Any Master Switch DTCs in the table below are output | A |
| Any D-Door Motor DTCs in the table below are output | B |
| Any P-Door Motor DTCs in the table below are output | C |
| No DTCs in the table below are output | D |
| Malfunction Status | System | Related DTCs | |
|---|---|---|---|
| Power Window Switch Malfunction | Master Switch | B2312 | ON Switch Failure |
| D-Door Motor | B2312 | Master Switch of Driver side door Malfunction | |
| P-Door Motor | B2312 | Power Window Switch of Passenger side door Malfunction | |
A
B
C
D
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| D Door P/W Up SW | Driver door power window manual up switch signal | OFF or ON | OFF: Driver door power window manual up switch not being operated
ON: Driver door power window manual up switch being operated |
- |
| D Door P/W Down SW | Driver door power window manual down switch signal | OFF or ON | OFF: Driver door power window manual down switch not being operated
ON: Driver door power window manual down switch being operated |
- |
| Tester Display |
|---|
| D Door P/W Up SW |
| D Door P/W Down SW |
On the GTS screen, ON or OFF is displayed accordingly.
| Proceed to |
|---|
| OK |
| NG |
OK
for 5 Door: Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for 5 Door Front Side)>REMOVAL
for 3 Door: Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for 3 Door Front Side)>REMOVAL
NG
Pre-procedure1
Disconnect the L7 power window regulator motor assembly (for driver door) connector.
procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| L7-10 (UP) - Body ground | Ignition switch ON | 11 to 14 V |
| L7-7 (DOWN) - Body ground | Ignition switch ON | 11 to 14 V |
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
for 5 Door: Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for 5 Door Front Side)>REMOVAL
for 3 Door: Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for 3 Door Front Side)>REMOVAL
NG
Pre-procedure1
Disconnect the L13 multiplex network master switch assembly connector.
procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L13-20 (UP) or L7-10 (UP) - Body ground | Always | 10 kΩ or higher |
| L13-15 (DOWN) or L7-7 (DOWN) - Body ground | Always | 10 kΩ or higher |
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| P Door P/W Auto SW | Front passenger door power window auto switch signal | OFF or ON | OFF: Front passenger door power window auto up or auto down switch not being operated
ON: Front passenger door power window auto up or auto down switch being operated |
- |
| P Door P/W Up SW | Front passenger door power window manual up switch signal | OFF or ON | OFF: Front passenger door power window manual up switch not being operated
ON: Front passenger door power window manual up switch being operated |
- |
| P Door P/W Down SW | Front passenger door power window manual down switch signal | OFF or ON | OFF: Front passenger door power window manual down switch not being operated
ON: Front passenger door power window manual down switch being operated |
- |
| Tester Display |
|---|
| P Door P/W Auto SW |
| P Door P/W Up SW |
| P Door P/W Down SW |
On the GTS screen, ON or OFF is displayed accordingly.
| Proceed to |
|---|
| OK |
| NG |
OK
for 5 Door: Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for 5 Door Front Side)>REMOVAL
for 3 Door: Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for 3 Door Front Side)>REMOVAL
NG
Click hereVehicle Exterior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the K7 power window regulator motor assembly (for Front Passenger Door) connector.
procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K13-5 (UP) or K7-10 (UP) - Body ground | Always | 10 kΩ or higher |
| K13-8 (AUTO) or K7-4 (AUTO) - Body ground | Always | 10 kΩ or higher |
| K13-4 (DOWN) or K7-7 (DOWN) - Body ground | Always | 10 kΩ or higher |
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
for 5 Door: Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for 5 Door Front Side)>REMOVAL
for 3 Door: Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for 3 Door Front Side)>REMOVAL
NG
Check for DTCs.
| Result | Proceed to |
|---|---|
| Any Master Switch DTCs in the table below are output | A |
| Any D-Door Motor DTCs in the table below are output | B |
| Any P-Door Motor DTCs in the table below are output | C |
| No DTCs in the table below are output | D |
| Malfunction Status | System | Related DTCs | |
|---|---|---|---|
| Power Window Switch Malfunction | Master Switch | B2312 | ON Switch Failure |
| D-Door Motor | B2312 | Master Switch of Driver side door Malfunction | |
| P-Door Motor | B2312 | Power Window Switch of Passenger side door Malfunction | |
A
B
C
D
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| D Door P/W Up SW | Driver door power window manual up switch signal | OFF or ON | OFF: Driver door power window manual up switch not being operated
ON: Driver door power window manual up switch being operated |
- |
| D Door P/W Down SW | Driver door power window manual down switch signal | OFF or ON | OFF: Driver door power window manual down switch not being operated
ON: Driver door power window manual down switch being operated |
- |
| Tester Display |
|---|
| D Door P/W Up SW |
| D Door P/W Down SW |
On the GTS screen, ON or OFF is displayed accordingly.
| Proceed to |
|---|
| OK |
| NG |
OK
for 5 Door: Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for 5 Door Front Side)>REMOVAL
for 3 Door: Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for 3 Door Front Side)>REMOVAL
NG
Pre-procedure1
Disconnect the K7 power window regulator motor assembly (for driver door) connector.
procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| K7-10 (UP) - Body ground | Ignition switch ON | 11 to 14 V |
| K7-7 (DOWN) - Body ground | Ignition switch ON | 11 to 14 V |
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
for 5 Door: Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for 5 Door Front Side)>REMOVAL
for 3 Door: Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for 3 Door Front Side)>REMOVAL
NG
Pre-procedure1
Disconnect the K5 multiplex network master switch assembly connector.
procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K5-20 (UP) or K7-10 (UP) - Body ground | Always | 10 kΩ or higher |
| K5-15 (DOWN) or K7-7 (DOWN) - Body ground | Always | 10 kΩ or higher |
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| P Door P/W Auto SW | Front passenger door power window auto switch signal | OFF or ON | OFF: Front passenger door power window auto up or auto down switch not being operated
ON: Front passenger door power window auto up or auto down switch being operated |
- |
| P Door P/W Up SW | Front passenger door power window manual up switch signal | OFF or ON | OFF: Front passenger door power window manual up switch not being operated
ON: Front passenger door power window manual up switch being operated |
- |
| P Door P/W Down SW | Front passenger door power window manual down switch signal | OFF or ON | OFF: Front passenger door power window manual down switch not being operated
ON: Front passenger door power window manual down switch being operated |
- |
| Tester Display |
|---|
| P Door P/W Auto SW |
| P Door P/W Up SW |
| P Door P/W Down SW |
On the GTS screen, ON or OFF is displayed accordingly.
| Proceed to |
|---|
| OK |
| NG |
OK
for 5 Door: Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for 5 Door Front Side)>REMOVAL
for 3 Door: Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for 3 Door Front Side)>REMOVAL
NG
Click hereVehicle Exterior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the L7 power window regulator motor assembly (for Front Passenger Door) connector.
procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L6-5 (UP) or L7-10 (UP) - Body ground | Always | 10 kΩ or higher |
| L6-8 (AUTO) or L7-4 (AUTO) - Body ground | Always | 10 kΩ or higher |
| L6-4 (DOWN) or L7-7 (DOWN) - Body ground | Always | 10 kΩ or higher |
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
for 5 Door: Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for 5 Door Front Side)>REMOVAL
for 3 Door: Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for 3 Door Front Side)>REMOVAL
NG
Check for DTCs.
| Result | Proceed to |
|---|---|
| Any Master Switch DTCs in the table below are output | A |
| Any D-Door Motor DTCs in the table below are output | B |
| Any P-Door Motor DTCs in the table below are output | C |
| Any RL-Door Motor DTCs in the table below are output | D |
| Any RR-Door Motor DTCs in the table below are output | E |
| No DTCs in the table below are output | F |
| Malfunction Status | System | Related DTCs | |
|---|---|---|---|
| Power Window Switch Malfunction | Master Switch | B2312 | ON Switch Failure |
| D-Door Motor | B2312 | Master Switch of Driver side door Malfunction | |
| P-Door Motor | B2312 | Power Window Switch of Passenger side door Malfunction | |
| RL-Door Motor | B2312 | Power Window Switch of Rear Left side door Malfunction | |
| RR-Door Motor | B2312 | Power Window Switch of Rear Right side door Malfunction | |
A
B
C
D
E
F
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| D Door P/W Up SW | Driver door power window manual up switch signal | OFF or ON | OFF: Driver door power window manual up switch not being operated
ON: Driver door power window manual up switch being operated |
- |
| D Door P/W Down SW | Driver door power window manual down switch signal | OFF or ON | OFF: Driver door power window manual down switch not being operated
ON: Driver door power window manual down switch being operated |
- |
| Tester Display |
|---|
| D Door P/W Up SW |
| D Door P/W Down SW |
On the GTS screen, ON or OFF is displayed accordingly.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for 5 Door Front Side)>REMOVAL
NG
Pre-procedure1
Disconnect the L7 power window regulator motor assembly (for driver door) connector.
procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| L7-10 (UP) - Body ground | Ignition switch ON | 11 to 14 V |
| L7-7 (DOWN) - Body ground | Ignition switch ON | 11 to 14 V |
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for 5 Door Front Side)>REMOVAL
NG
Pre-procedure1
Disconnect the L13 multiplex network master switch assembly connector.
procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L13-20 (UP) or L7-10 (UP) - Body ground | Always | 10 kΩ or higher |
| L13-15 (DOWN) or L7-7 (DOWN) - Body ground | Always | 10 kΩ or higher |
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| P Door P/W Auto SW | Front passenger door power window auto switch signal | OFF or ON | OFF: Front passenger door power window auto up or auto down switch not being operated
ON: Front passenger door power window auto up or auto down switch being operated |
- |
| P Door P/W Up SW | Front passenger door power window manual up switch signal | OFF or ON | OFF: Front passenger door power window manual up switch not being operated
ON: Front passenger door power window manual up switch being operated |
- |
| P Door P/W Down SW | Front passenger door power window manual down switch signal | OFF or ON | OFF: Front passenger door power window manual down switch not being operated
ON: Front passenger door power window manual down switch being operated |
- |
| Tester Display |
|---|
| P Door P/W Auto SW |
| P Door P/W Up SW |
| P Door P/W Down SW |
On the GTS screen, ON or OFF is displayed accordingly.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for 5 Door Front Side)>REMOVAL
NG
Click hereVehicle Exterior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the K7 power window regulator motor assembly (for Front Passenger Door) connector.
procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K13-5 (UP) or K7-10 (UP) - Body ground | Always | 10 kΩ or higher |
| K13-8 (AUTO) or K7-4 (AUTO) - Body ground | Always | 10 kΩ or higher |
| K13-4 (DOWN) or K7-7 (DOWN) - Body ground | Always | 10 kΩ or higher |
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for 5 Door Front Side)>REMOVAL
NG
Check for DTCs.
| Result | Proceed to |
|---|---|
| Any Master Switch DTCs in the table below are output | A |
| Any D-Door Motor DTCs in the table below are output | B |
| Any P-Door Motor DTCs in the table below are output | C |
| Any RL-Door Motor DTCs in the table below are output | D |
| Any RR-Door Motor DTCs in the table below are output | E |
| No DTCs in the table below are output | F |
| Malfunction Status | System | Related DTCs | |
|---|---|---|---|
| Power Window Switch Malfunction | Master Switch | B2312 | ON Switch Failure |
| D-Door Motor | B2312 | Master Switch of Driver side door Malfunction | |
| P-Door Motor | B2312 | Power Window Switch of Passenger side door Malfunction | |
| RL-Door Motor | B2312 | Power Window Switch of Rear Left side door Malfunction | |
| RR-Door Motor | B2312 | Power Window Switch of Rear Right side door Malfunction | |
A
B
C
D
E
F
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| D Door P/W Up SW | Driver door power window manual up switch signal | OFF or ON | OFF: Driver door power window manual up switch not being operated
ON: Driver door power window manual up switch being operated |
- |
| D Door P/W Down SW | Driver door power window manual down switch signal | OFF or ON | OFF: Driver door power window manual down switch not being operated
ON: Driver door power window manual down switch being operated |
- |
| Tester Display |
|---|
| D Door P/W Up SW |
| D Door P/W Down SW |
On the GTS screen, ON or OFF is displayed accordingly.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for 5 Door Front Side)>REMOVAL
NG
Pre-procedure1
Disconnect the K7 power window regulator motor assembly (for driver door) connector.
procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| K7-10 (UP) - Body ground | Ignition switch ON | 11 to 14 V |
| K7-7 (DOWN) - Body ground | Ignition switch ON | 11 to 14 V |
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for 5 Door Front Side)>REMOVAL
NG
Pre-procedure1
Disconnect the K5 multiplex network master switch assembly connector.
procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K5-20 (UP) or K7-10 (UP) - Body ground | Always | 10 kΩ or higher |
| K5-15 (DOWN) or K7-7 (DOWN) - Body ground | Always | 10 kΩ or higher |
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| P Door P/W Auto SW | Front passenger door power window auto switch signal | OFF or ON | OFF: Front passenger door power window auto up or auto down switch not being operated
ON: Front passenger door power window auto up or auto down switch being operated |
- |
| P Door P/W Up SW | Front passenger door power window manual up switch signal | OFF or ON | OFF: Front passenger door power window manual up switch not being operated
ON: Front passenger door power window manual up switch being operated |
- |
| P Door P/W Down SW | Front passenger door power window manual down switch signal | OFF or ON | OFF: Front passenger door power window manual down switch not being operated
ON: Front passenger door power window manual down switch being operated |
- |
| Tester Display |
|---|
| P Door P/W Auto SW |
| P Door P/W Up SW |
| P Door P/W Down SW |
On the GTS screen, ON or OFF is displayed accordingly.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for 5 Door Front Side)>REMOVAL
NG
Click hereVehicle Exterior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the L7 power window regulator motor assembly (for Front Passenger Door) connector.
procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L6-5 (UP) or L7-10 (UP) - Body ground | Always | 10 kΩ or higher |
| L6-8 (AUTO) or L7-4 (AUTO) - Body ground | Always | 10 kΩ or higher |
| L6-4 (DOWN) or L7-7 (DOWN) - Body ground | Always | 10 kΩ or higher |
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for 5 Door Front Side)>REMOVAL
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RL Door P/W Auto SW | Rear LH door power window auto switch signal | OFF or ON | OFF: Rear LH door power window auto up or auto down switch not being operated
ON: Rear LH door power window auto up or auto down switch being operated |
- |
| RL Door P/W Up SW | Rear LH door power window manual up switch signal | OFF or ON | OFF: Rear LH door power window manual up switch not being operated
ON: Rear LH door power window manual up switch being operated |
- |
| RL Door P/W Down SW | Rear LH door power window manual down switch signal | OFF or ON | OFF: Rear LH door power window manual down switch not being operated
ON: Rear LH door power window manual down switch being operated |
- |
| Tester Display |
|---|
| RL Door P/W Auto SW |
| RL Door P/W Up SW |
| RL Door P/W Down SW |
On the GTS screen, ON or OFF is displayed accordingly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the N4 power window regulator motor assembly (for Rear LH Door) connector.
procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N3-5 (UP) or N4-10 (UP) - Body ground | Always | 10 kΩ or higher |
| N3-4 (DOWN) or N4-7 (DOWN) - Body ground | Always | 10 kΩ or higher |
| N3-8 (AUTO) or N4-4 (AUTO) - Body ground | Always | 10 kΩ or higher |
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RR Door P/W Auto SW | Rear RH door power window auto switch signal | OFF or ON | OFF: Rear RH door power window auto up or auto down switch not being operated
ON: Rear RH door power window auto up or auto down switch being operated |
- |
| RR Door P/W Up SW | Rear RH door power window manual up switch signal | OFF or ON | OFF: Rear RH door power window manual up switch not being operated
ON: Rear RH door power window manual up switch being operated |
- |
| RR Door P/W Down SW | Rear RH door power window manual down switch signal | OFF or ON | OFF: Rear RH door power window manual down switch not being operated
ON: Rear RH door power window manual down switch being operated |
- |
| Tester Display |
|---|
| RR Door P/W Auto SW |
| RR Door P/W Up SW |
| RR Door P/W Down SW |
On the GTS screen, ON or OFF is displayed accordingly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the M4 power window regulator motor assembly (for rear RH door) connector.
procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M3-5 (UP) or M4-10 (UP) - Body ground | Always | 10 kΩ or higher |
| M3-4 (DOWN) or M4-7 (DOWN) - Body ground | Always | 10 kΩ or higher |
| M3-8 (AUTO) or M4-4 (AUTO) - Body ground | Always | 10 kΩ or higher |
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
NG