Home › Drivetrain › EA67F (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSAXLE ASSEMBLY › from 2020.09
RM36W0E _52 Drivetrain _095283 EA67F MANUAL TRANSMISSION / TRANSAXLE _0449598 MANUAL TRANSAXLE ASSEMBLY A

EA67F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the manual transaxle assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Hide 11363A 2.REMOVE FLYWHEEL HOUSING SIDE COVER

Hide 28100 3.REMOVE STARTER ASSEMBLY

Hide 31483 4.REMOVE BLEEDER CLUTCH RELEASE TUBE

Hide 31407B 5.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

Hide 31224 6.REMOVE CLUTCH RELEASE BEARING PLATE

Hide 31400 7.REMOVE CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY

Hide 31483 8.REMOVE CLUTCH RELEASE CYLINDER TO BLEEDER TUBE

Hide 31485 9.REMOVE CLUTCH FLEXIBLE HOSE BRACKET

a.
C450880

Remove the bolt and clutch flexible hose bracket from the manual transmission case.


Hide 82121 10.DISCONNECT ENGINE WIRE

a.
C450881

Disconnect the 4 connectors from the manual transaxle assembly.


b.

Disengage the 2 clamps to disconnect the engine wire from the transaxle assembly.


c.

Remove the 2 bolts and disconnect the engine wire from the manual transaxle assembly.


d.
C450882

Remove the bolt.


e.

Disengage the clamp to disconnect the engine wire from the engine assembly.


f.
C450883

Disconnect the 3 clamps and engine wire from the manual transaxle assembly.


Hide 25051 11.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

Hide 17279 12.REMOVE TURBINE OUTLET ELBOW GASKET

Hide 51201 13.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.
C450884

Remove the bolt and front suspension crossmember sub-assembly from the No. 2 engine moving control rod.


Hide 12364B 14.REMOVE NO. 2 ENGINE MOVING CONTROL ROD

a.
C450885

Remove the 4 bolts and No. 2 engine moving control rod from the manual transaxle assembly.


Hide 37117B 15.REMOVE PROPELLER SHAFT HEAT INSULATOR

a.
C450886

Remove the 2 bolts and propeller shaft heat insulator from the transfer assembly.


Hide 36100 16.LOOSEN TRANSFER ASSEMBLY

a.
C450887

Loosen the 2 bolts and 2 nuts.


b.
C450888

Loosen the 4 nuts.


Hide 30300 17.REMOVE MANUAL TRANSAXLE ASSEMBLY

a.
C450890

Remove the bolt.


b.
C450889

Remove the 6 bolts and remove the manual transaxle assembly.


Hide 36100 18.REMOVE TRANSFER ASSEMBLY

a.
C451046

Remove the 2 bolts and 2 nuts.


b.
C451047

Remove the 4 nuts and transfer assembly from the manual transaxle assembly.


Hide 17568A 19.REMOVE EXHAUST PIPE SUPPORT STAY

a.
C450891

Remove the 2 bolts and exhaust pipe support stay from the manual transaxle assembly.


Hide 20.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C450892

Remove the 2 bolts and 2 wire harness clamp brackets from the manual transaxle assembly.


b.
C450893

Remove the bolt and wire harness clamp bracket from the manual transaxle assembly.


Hide 33111A 21.REMOVE MANUAL TRANSMISSION CASE PLUG

a.
C450894

Remove the manual transmission case plug from the manual transaxle assembly.


Hide 36100A 22.REMOVE TRANSFER AND TRANSAXLE SETTING STUD BOLT

a.
C450895

Remove the 2 transfer and transaxle setting stud bolts.

HINT:

It is not necessary to remove the manual transaxle assembly.