Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER (for 5 Door) › 2020.09–2021.11
RM36W0E _59 Vehicle Exterior _088302 EXTERIOR PANELS / TRIM _0447291 FRONT BUMPER(for 5 Door) A

EXTERIOR PANELS / TRIM  FRONT BUMPER(for 5 Door)  REASSEMBLY  


PROCEDURE

Hide 52618 1.INSTALL FRONT BUMPER LOWER ABSORBER

a.
B562728

Install the 4 grommets.


b.
B562727

Engage the claws to install the front bumper lower absorber.


c.
B562726C01
0.229,0.698 0.448,0.875 0.219,0.177 10 true *a 1.885,0.667 2.073,0.865 0.188,0.198 10 true *b 0.51,0.604 0.729,0.781 0.219,0.177 10 true *a 1.146,0.594 1.344,0.781 0.198,0.188 10 true *a 1.448,0.698 1.646,0.885 0.198,0.188 10 true *a 2.115,0.615 2.313,0.802 0.198,0.188 10 true *a 2.708,0.594 2.906,0.781 0.198,0.188 10 true *a 3.042,0.698 3.24,0.885 0.198,0.188 10 true *a
*a screw
*b clip


Install the clip and 7 screws.


Hide 51451A 2.INSTALL CENTER ENGINE UNDER COVER

Hide 52103A 3.INSTALL FRONT BUMPER EXTENSION SUB-ASSEMBLY LH (for TMMF Made)

a.
B594623N01
1.458,0.104 1.625,0.323 0.167,0.219 12 true A 1.844,0.25 2.01,0.469 0.167,0.219 12 true A 3,1.729 3.146,1.927 0.146,0.198 12 true B

Install the front bumper extension sub-assembly LH with 3 bolts.

Torque:
Bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
Bolt B : 30 N*m (306 kgf*cm, 266 in.*lbf)


Hide 52102B 4.INSTALL FRONT BUMPER EXTENSION SUB-ASSEMBLY RH (for TMMF Made)

HINT:

Use the same procedure as for the LH side.


Hide 57014C 5.INSTALL FRONT SIDE MEMBER BRACKET SUB-ASSEMBLY LH

a.

If install a new front side member bracket sub-assembly LH:

i.

Temporarily install the front side member bracket sub-assembly LH with the 5 bolts until the "reference value" and " point-to-point distance" are aligned.

·

Vehicle Exterior > BODY PANEL > RADIATOR SUPPORT(for 5 Door) > REFERENCE VALUE

·

Vehicle Exterior > BODY DIMENSIONS > ENGINE COMPARTMENT REFERENCE VALUES(for 5 Door) > POINT-TO-POINT DISTANCE




b.

If reusing the front side member bracket sub-assembly LH:

i.

Temporarily install the front side member bracket sub-assembly LH with the 5 bolts until the matchmarks are aligned.

B577632



c.
B577630C01
2.292,0.281 2.448,0.49 0.156,0.208 10 true A 2.792,1.229 2.948,1.438 0.156,0.208 10 true A 2.313,1.927 2.469,2.135 0.156,0.208 10 true A 1.188,0.042 1.344,0.25 0.156,0.208 10 true B 1.135,0.49 1.292,0.698 0.156,0.208 10 true B

Tighten the 5 bolts.

Torque:
Bolt A : 30 N*m (306 kgf*cm, 22 ft.*lbf)
Bolt B : 7.1 N*m (72 kgf*cm, 63 in.*lbf)


d.

Engage the clamp.


Hide 57013D 6.INSTALL FRONT SIDE MEMBER BRACKET SUB-ASSEMBLY RH

a.

If install a new front side member bracket sub-assembly RH:

i.

Temporarily install the front side member bracket sub-assembly RH with the 5 bolts until the "reference value" and " point-to-point distance" are aligned.

·

Vehicle Exterior > BODY PANEL > RADIATOR SUPPORT(for 5 Door) > REFERENCE VALUE

·

Vehicle Exterior > BODY DIMENSIONS > ENGINE COMPARTMENT REFERENCE VALUES(for 5 Door) > POINT-TO-POINT DISTANCE




b.

If reusing the front side member bracket sub-assembly RH:

i.

Temporarily install the front side member bracket sub-assembly RH with the 5 bolts until the matchmarks are aligned.

B577633



c.
B562725C01
1.208,0.229 1.375,0.417 0.167,0.188 10 true A 0.698,0.833 0.865,1.063 0.167,0.229 10 true A 1.188,1.76 1.354,1.99 0.167,0.229 10 true A 2.24,0.563 2.417,0.76 0.177,0.198 10 true B 2.25,0.313 2.427,0.51 0.177,0.198 10 true B

Tighten the 5 bolts.

Torque:
Bolt A : 30 N*m (306 kgf*cm, 22 ft.*lbf)
Bolt B : 7.1 N*m (72 kgf*cm, 63 in.*lbf)


Hide 16595D 7.INSTALL NO. 1 RADIATOR AIR GUIDE LH

a.
B562730C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the claws to Install the No. 1 radiator air guide LH as shown in the illustration.


Hide 16561D 8.INSTALL NO. 1 RADIATOR TO SUPPORT SEAL

a.
B562731C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the claws to install the No. 1 radiator to support seal as shown in the illustration.


Hide 9.INSTALL NO. 2 RADIATOR TO SUPPORT SEAL

a.

for Gasoline Model:

i.
B568025C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the No. 2 radiator to support seal as shown in the illustration.



b.

for HV Model:

i.
B568026C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the No. 2 radiator to support seal as shown in the illustration.



Hide 16695A 10.INSTALL FRONT RADIATOR SIDE AIR GUIDE PLATE LH

a.
B568023C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the front radiator side air guide plate LH as shown in the illustration.


Hide 16691A 11.INSTALL FRONT RADIATOR SIDE AIR GUIDE PLATE RH

a.
B568024C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the front radiator side air guide plate RH as shown in the illustration.


Hide 52131A 12.INSTALL FRONT BUMPER REINFORCEMENT

a.
B562717

Install the front bumper reinforcement with 8 bolts and 2 nuts.

Torque:
Bolt : 30 N*m (306 kgf*cm, 22 ft.*lbf)
Nut : 7.1 N*m (72 kgf*cm, 63 in.*lbf)


b.
B562716

Engage the wire harness clamps.


Hide 88790B 13.INSTALL THERMISTOR ASSEMBLY

a.
B562715

Engage the clamps to install the thermistor assembly.


Hide 52611 14.INSTALL FRONT BUMPER ENERGY ABSORBER

a.
B562714

Engage the guides to install the front bumper energy absorber.


Hide 16681A 15.INSTALL RADIATOR UPPER AIR GUIDE PLATE

a.
B562713

Engage the clips to install the radiator upper air guide plate.


b.

Engage the wire harness clamp.


Hide 52536 16.INSTALL FRONT BUMPER SIDE RETAINER LH

a.
B577628

Engage the 2 claws to install the front bumper side retainer LH.


Hide 52535 17.INSTALL FRONT BUMPER SIDE RETAINER RH

HINT:

Use the same procedure as for the LH side.


Hide 19.INSTALL HEADLIGHT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 53879H 20.INSTALL FRONT FENDER LINER RETAINER

a.
B562711

Engage the claw to install the front fender liner retainer.

HINT:

Use the same procedure for the RH side and LH side.



Hide 53112E 21.INSTALL NO. 1 LOWER RADIATOR GRILLE

a.

for TMC Made:

i.

Engage the claws to install the No. 1 lower radiator grille.

B602859


ii.

Install the 2 screws.



b.

except TMC Made:

i.

Engage the claws to install the No. 1 lower radiator grille.

B562709


ii.

Install the 3 screws.



Hide 53101 22.INSTALL RADIATOR GRILLE SUB-ASSEMBLY

a.

for TMC Made:

i.
B562706

Install the 2 nuts.



b.
B562705

Engage the claws to install the radiator grille sub-assembly.


c.

Install the 4 clips and 2 screws.


Hide 53155D 23.INSTALL NO. 1 RADIATOR GRILLE SEAL

a.
B562703

Engage the claws to install the No. 1 radiator grille seal.


b.

Install the 2 screws.


Hide 53395E 24.INSTALL HOOD TO FRONT END PANEL SEAL

a.
B562704

Engage the clips to install the hood to front end panel seal.


Hide 52129D 25.INSTALL FRONT BUMPER LOWER COVER

a.
B562708

Engage the hook to install the front bumper lower cover.


b.

Engage the claws.


Hide 52127C 26.INSTALL FRONT BUMPER HOLE COVER

a.
B562710

Engage the hook to install the front bumper hole cover.


b.

Engage the claws.


Hide 52113D 27.INSTALL FRONT BUMPER EXTENSION LH (w/ Fog Light)

a.
B562701

Engage the claws to install the front bumper extension LH.


b.
B562700

Install the moulding retainer.


Hide 52112D 28.INSTALL FRONT BUMPER EXTENSION RH (w/ Fog Light)

HINT:

Use the same procedure as for the LH side.


Hide 52113D 29.INSTALL FRONT BUMPER EXTENSION LH (w/o Fog Light)

a.
B562702

Engage the claws to install the front bumper extension LH.


Hide 52112D 30.INSTALL FRONT BUMPER EXTENSION RH (w/o Fog Light)

HINT:

Use the same procedure as for the LH side.


Hide 81210A 32.INSTALL FOGLIGHT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 33.INSTALL WIRING HARNESS CONNECTOR (w/o Parking Support Brake System)

a.
B577627

Engage the clamp to install the wiring harness connector.


Hide 75311 34.INSTALL RADIATOR GRILLE (OR FRONT PANEL) EMBLEM

HINT:

When installing the radiator grille (or front panel) emblem, heat the front bumper assembly and radiator grille (or front panel) emblem a heat light.

Item Temperature
·

Front Bumper Assembly

·

Radiator Grille (or front panel) Emblem


20 to 30°C (68 to 86°F)


CAUTION:
E439696C01
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the front bumper assembly and radiator grille (or front panel) emblem excessively.


a.
B577658C01
0.563,4.063 0.865,3.594 false 2.135,4.271 2.458,3.802 false 0.396,3.979 0.708,4.177 0.313,0.198 10 false *a 1.958,4.188 2.271,4.385 0.313,0.198 10 false *a
*a Location Pin


Clean the front bumper assembly surface.

i.

Using a heat light, heat the front bumper assembly surface.


ii.

Remove any remaining double-sided tape from the front bumper assembly.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Using a heat light, heat the front bumper assembly and a new radiator grille (or front panel) emblem.


c.

Remove the release paper from the radiator grille (or front panel) emblem.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



d.

Engage the location pins and install the radiator grille (or front panel) emblem as shown in the illustration.


Hide 82113 35.INSTALL NO. 3 ENGINE ROOM WIRE (w/ Wire Harness)

a.

for TMC Made with Parking Support Brake System:

i.

Engage the clamps to install the No. 3 engine room wire.

B570633



b.

for TMMF Made with Parking Support Brake System:

i.

Engage the clamps to install the No. 3 engine room wire.

B562732



c.

w/o Parking Support Brake System:

i.

Engage the clamps to install the No. 3 engine room wire.

B570632



Hide 88211B 36.INSTALL MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Toyota Safety Sense 2)

Hide 89347B 37.INSTALL FRONT CORNER ULTRASONIC SENSOR RETAINER (w/ Parking Support Brake System)

Hide 89341L 38.INSTALL FRONT CENTER ULTRASONIC SENSOR (w/ Parking Support Brake System)

Hide 89341K 39.INSTALL FRONT CORNER ULTRASONIC SENSOR (w/ Parking Support Brake System)

Hide 89348N 40.INSTALL NO. 1 ULTRASONIC SENSOR CLIP (w/ Parking Support Brake System)