Home › Suspension › FRONT SUSPENSION › FRONT SUSPENSION MEMBER (except G16E-GTS) › 2020.09–2021.11
RM36W0E _53 Suspension _087263 FRONT SUSPENSION _0447911 FRONT SUSPENSION MEMBER(except G16E-GTS) A

FRONT SUSPENSION  FRONT SUSPENSION MEMBER(except G16E-GTS)  INSTALLATION  


PROCEDURE

Hide 48811 1.INSTALL FRONT STABILIZER BAR

Hide 2.INSTALL STEERING LINK ASSEMBLY

Hide 48069 3.TEMPORARILY INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.
C428505C02
0,0.094 0.302,0.302 0.302,0.208 12 true *A 0,2.417 0.375,2.667 0.375,0.25 12 true *B
*A for TMC Made
*B for TMMF Made


Temporarily install the front lower No. 1 suspension arm sub-assembly LH to the front suspension crossmember sub-assembly with the 2 bolts and nut.


Hide 48068 4.TEMPORARILY INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 12363A 5.INSTALL ENGINE MOVING CONTROL ROD

a.

Install the engine moving control rod to the front suspension crossmember sub-assembly with the bolt.

Torque:
200 N*m (2039 kgf*cm, 148 ft.*lbf)


Hide 51228G 6.INSTALL FRONT SUSPENSION MEMBER PLATE (w/ Plate)

a.

Install the front suspension member plate to the front suspension member sub-assembly with the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 51201 7.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.

Slowly jack up the front suspension crossmember sub-assembly with an engine lifter using 4 attachments or equivalent tools.

CAUTION:
C320210

·

The front suspension crossmember sub-assembly is a very heavy component. Make sure that it is supported securely.

·

If the front suspension crossmember sub-assembly is not securely supported, it may drop, resulting in serious injury.



NOTICE:
·

Use attachments to keep the front suspension crossmember sub-assembly level.

·

Make sure that the front suspension crossmember sub-assembly not hit the protrusion of the reinforcement.

·
C430482C01
0.583,1.948 0.885,2.177 0.302,0.229 10 true *a 2.385,1.948 2.688,2.177 0.302,0.229 10 true *b
*a OK
*b NG


After installation, check that the claws of the steering column hole cover base are not disengaged.




b.
C432279N01
0.552,1.302 0.708,1.5 0.156,0.198 10 true A 2.719,1.333 2.875,1.531 0.156,0.198 10 true A 0.656,1.604 0.813,1.802 0.156,0.198 10 true A 2.635,1.604 2.792,1.802 0.156,0.198 10 true A 0.552,1.958 0.708,2.156 0.156,0.198 10 true A 2.74,1.948 2.896,2.146 0.156,0.198 10 true A 2.198,0.385 2.354,0.583 0.156,0.198 10 true A 1.094,0.365 1.25,0.563 0.156,0.198 10 true A 0.333,0.094 0.49,0.292 0.156,0.198 10 true B 2.958,0.104 3.115,0.302 0.156,0.198 10 true B

Install the front suspension crossmember sub-assembly to the vehicle body with the 8 bolts (A).

Torque:
107.5 N*m (1096 kgf*cm, 79 ft.*lbf)


c.

Install the 2 bolts (B).

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


d.

Lower the engine lifter.


e.

Install the engine moving control rod with the bolt.

Torque:
170 N*m (1734 kgf*cm, 125 ft.*lbf)


f.

except 1KR-FE:

i.

Install the wiring harness clamp bracket to the front suspension crossmember sub-assembly with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)



Hide 17410 8.INSTALL FRONT EXHAUST PIPE ASSEMBLY (for 1KR-FE)

Hide 57543C 9.INSTALL CENTER NO. 1 FLOOR BRACE (for 1KR-FE)

Hide 48069 10.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH (for TMC Made)

Hide 48069 11.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH (for TMMF Made)

Hide 48068 12.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH (for TMC Made)

HINT:

Perform the same procedure as for the LH side.


Hide 48068 13.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH (for TMMF Made)

HINT:

Perform the same procedure as for the LH side.


Hide 45047 14.CONNECT TIE ROD END SUB-ASSEMBLY LH (for TMC Made)

a.
C398436

Connect the tie rod end sub-assembly LH to the steering knuckle LH with the nut.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)

NOTICE:
·

Do not damage the ball joint dust cover.

·

Further tighten the nut up to 60° if the holes for the cotter pin are not aligned.




b.

Install a new cotter pin.


Hide 45047 15.CONNECT TIE ROD END SUB-ASSEMBLY LH (for TMMF Made)

a.
C398436

Connect the tie rod end sub-assembly LH to the steering knuckle LH with the nut.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)

NOTICE:
·

Do not damage the ball joint dust cover.

·

Further tighten the nut up to 60° if the holes for the cotter pin are not aligned.




b.

Install a new cotter pin.


c.
C439571C02
0,0 0,0 false
V113147

Install in this Direction


Engage the claw to install a new steering knuckle seal as shown in the illustration.

HINT:

Check that the steering knuckle seal is securely installed.



Hide 45046 16.CONNECT TIE ROD END SUB-ASSEMBLY RH (for TMC Made)

HINT:

Perform the same procedure as for the LH side.


Hide 45046 17.CONNECT TIE ROD END SUB-ASSEMBLY RH (for TMMF Made)

HINT:

Perform the same procedure as for the LH side.


Hide 48810 18.CONNECT FRONT STABILIZER LINK ASSEMBLY LH

a.

Connect the front stabilizer link assembly LH to the front stabilizer bar with the nut.

Torque:
74 N*m (755 kgf*cm, 55 ft.*lbf)

NOTICE:

Do not damage the boot of the ball joint.


HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.



Hide 48820B 19.CONNECT FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 53876A 20.INSTALL FRONT FENDER LINER LH (w/ Engine Under Cover Assembly)

a.

Install the front fender liner LH to the vehicle body with the 2 screws.


Hide 53875A 21.INSTALL FRONT FENDER LINER RH (w/ Engine Under Cover Assembly)

HINT:

Perform the same procedure as for the LH side.


Hide 22.INSTALL FRONT WHEELS

Hide 45260 23.CONNECT NO.2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45259A 24.INSTALL COLUMN HOLE COVER SILENCER SHEET (for LHD)

Hide 45259A 25.INSTALL COLUMN HOLE COVER SILENCER SHEET (for RHD)

Hide 48069 27.FULLY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH (for TMC Made)

Hide 48069 28.FULLY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH (for TMMF Made)

Hide 48068 29.FULLY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH (for TMC Made)

Hide 48068 30.FULLY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH (for TMMF Made)

Hide 51447D 31.INSTALL CENTER NO. 4 ENGINE UNDER COVER (for TMC Made)

a.

Install the center No. 4 engine under cover to the vehicle with the 2 bolts and 2 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 51447D 32.INSTALL CENTER NO. 4 ENGINE UNDER COVER (for TMMF Made)

a.

except 1KR-FE:

i.

Install the center No. 4 engine under cover to the vehicle with the 4 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)



Hide 51442C 33.INSTALL ENGINE UNDER COVER LH

a.

w/ Center Engine Under Cover for Full Cover Type, w/ Center Engine Under Cover for Half Cover Type:

i.

Install the engine under cover LH to the vehicle with the 2 clips.



b.

w/o Center Engine Under Cover:

i.

Install the engine under cover LH to the vehicle with the 3 clips.



Hide 51441C 34.INSTALL ENGINE UNDER COVER RH

HINT:

Perform the same procedure as for the LH side.


Hide 51451A 35.INSTALL CENTER ENGINE UNDER COVER

a.

w/ Center Engine Under Cover for Full Cover Type:

i.

Install the center engine under cover to the vehicle with the 4 bolts, 4 screws and 9 clips.

Torque:
Bolt : 5.0 N*m (51 kgf*cm, 44 in.*lbf)



b.

w/ Center Engine Under Cover for Half Cover Type:

i.

Install the center engine under cover to the vehicle with the 4 bolts, 4 screws and 7 clips.

Torque:
Bolt : 5.0 N*m (51 kgf*cm, 44 in.*lbf)



Hide 36.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 37.PERFORM INITIALIZATION

Parking support brake system (Click here)
Parking assist monitor system (Click here)