Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT DOOR BELT MOULDING › 2020.09–2021.11
RM36W0E _59 Vehicle Exterior _088302 EXTERIOR PANELS / TRIM _0421042 FRONT DOOR BELT MOULDING A

EXTERIOR PANELS / TRIM  FRONT DOOR BELT MOULDING  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during the front door belt moulding removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Door glass Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Remote control function

·

Key-linked function

·

Wireless transmitter-linked function

·

Key-off operation function

·

Catch protection function

·

Window open warning function


(Click here)

HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1:for Gasoline Model

Lane control system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system*1 Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 87940 3.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY (for TMC Made)

Hide 87940 4.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY (for TMMF Made)

Hide 67832 5.REMOVE FRONT DOOR SERVICE HOLE COVER

Hide 6.REMOVE HOLE PLUG (for 5 Door)

a.
B584244

Remove the hole plug.


Hide 7.REMOVE HOLE PLUG (for 3 Door)

Hide 68102 8.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

Hide 68210C 9.REMOVE FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

a.

for 5 Door:

i.
B567972C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the front door glass outer weatherstrip assembly.


ii.
B567973C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws to remove the front door glass outer weatherstrip assembly as shown in the illustration.



b.

for 3 Door:

i.
B596023C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the front door glass outer weatherstrip assembly.


ii.
B596024

Disengage the claws to remove the front door glass outer weatherstrip assembly as shown in the illustration.