The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the front door removal/installation are shown below.
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Use the same procedure for the LH side and RH side.
The following procedure is for the LH side.
1. PRECAUTION
Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
2. CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
Click hereGeneral>MAINTENANCE>G16E-GTS AUXILIARY BATTERY>REMOVAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
67492A
3.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH
Disengage the claws and clip to remove the front door lower frame bracket garnish.
74232
4.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Driver Side)
Disengage the claws and guides.
Disconnect the 2 connectors to remove the multiplex network master switch assembly with front armrest base upper panel.
74231
5.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Front Passenger Side)
Disengage the claws and guides.
Disconnect the connector to remove the power window regulator switch assembly with front armrest base upper panel.
67656
6.REMOVE FRONT DOOR TRIM GARNISH
|
Remove in this Direction |
Remove the screw.
Disengage the claws to remove the front door trim garnish as shown in the illustration.
67602
7.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY
| *a | Protective Tape |
Using a screwdriver with its tip wrapped in protective tape, disengage the claw to open the front door inside handle bezel plug.
Remove the 3 screws.
|
Place Hands Here |
|
Remove in this Direction |
Disengage the clips as shown in the illustration.
|
Remove in this Direction |
Disengage the front door trim board sub-assembly with the front door glass inner weatherstrip, front door vent seal and front door panel protector as shown in the illustration.
| *1 | Front Door Lock/Unlock Knob Inside Locking Cable |
| *2 | Front Door Lock Open Lever Remote Control Cable |
|
Remove in this Direction |
Disengage the guides to disconnect the front door lock/unlock knob inside locking cable and front door lock open lever remote control cable to remove the front door trim board sub-assembly as shown in the illustration.
8.REMOVE NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY (w/ Interior Illumination)
Disengage the claws to remove the No. 1 interior illumination light assembly
69206B
9.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY
Disengage the guides to remove the front door inside handle sub-assembly.
69284C
10.REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG
Disengage the claw to remove front door inside handle bezel plug.
68172A
11.REMOVE FRONT DOOR GLASS INNER WEATHERSTRIP
|
Remove in this Direction |
Disengage the claws to remove the front door glass inner weatherstrip as shown in the illustration.
86160
12.REMOVE NO. 1 FRONT SPEAKER ASSEMBLY
13.REMOVE NO. 1 FRONT SPEAKER BRACKET
Disengage the guide.
Remove the 3 screws and No. 1 front speaker bracket.
87940
14.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY
67832
15.REMOVE FRONT DOOR SERVICE HOLE COVER
| *a | Clamp |
| *b | Guide |
Turn the 3 front door service hole cover clips 45° to remove it clips as shown in the illustration.
Disengage the guides and clamp to separate the wire harness from the front door service hole cover.
Disengage the clips to remove the front door service hole cover.
8983AA
16.REMOVE SIDE AIRBAG PRESSURE SENSOR
17.REMOVE HOLE PLUG
Remove the 4 hole plugs.
18.REMOVE WINDOW REGULATOR SHIM
Loosen the 2 nut.
Remove the 2 window regulator shims.
68102
19.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY
for Driver Side:
Connect the multiplex network master switch assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Move the front door glass sub-assembly so that the door glass bolts can be seen.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the multiplex network master switch assembly.
for Front Passenger Side:
Connect the power window regulator switch assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Move the front door glass sub-assembly so that the door glass bolts can be seen.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the power window regulator switch assembly.
Remove the 3 nuts.
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Remove the front door glass sub-assembly as shown in the illustration.
Do not damage the front door glass sub-assembly.
69820
20.REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY
|
Nut |
|
Connector |
Disconnect the connector.
Remove the 7 nuts and front door window regulator assembly.
21.REMOVE HOLE SEAL
Remove the 2 hole seals.
22.REMOVE FRONT DOOR UPPER WINDOW STOP
Remove the 2 bolts.
Disengage the guides to remove the 2 front door upper window stops.
23.REMOVE HOLE SEAL
Remove the 2 hole seals.
24.REMOVE DOOR GLASS FEMALE STABILIZER
Remove the bolt.
Disengage the guide to remove the door glass female stabilizer.
68151C
25.REMOVE FRONT DOOR GLASS RUN
Remove the front door glass run.
67402F
26.REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY
Remove the bolt, nut and front door front lower frame sub-assembly.
69220
27.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY
w/ Entry and Start System:
| *a | Protective Tape |
Disengage the claws.
Using a screwdriver with its tip wrapped in protective tape, disconnect the connector.
Disengage the 2 claws and move the lever as shown in the illustration.
|
Remove in this Direction |
Remove the front door outside handle assembly as shown in the illustration.
28.REMOVE FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)
Remove the hole plug.
Using a T30 "TORX" socket wrench, loosen the screw.
Remove the front door lock cylinder assembly.
69217F
29.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)
Remove the hole plug.
Using a T30 "TORX" socket wrench, loosen the screw.
Disengage the claws and guides to remove the front door outside handle cover.
69241H
30.REMOVE FRONT DOOR OUTSIDE HANDLE FRONT PAD
Disengage the claws and guide to remove the front door front outside handle pad.
69242E
31.REMOVE FRONT DOOR OUTSIDE HANDLE REAR PAD
Disengage the guides to remove the front door outside handle rear pad.
69040A
32.REMOVE FRONT DOOR WITH MOTOR LOCK ASSEMBLY
69202A
33.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
w/ Entry and Start System:
Disengage the clamp to separate the wire harness.
|
Remove in this Direction |
Using a T30 "TORX" socket wrench, loosen the screw.
Disengage the guides to remove the front door outside handle frame sub-assembly as shown in the illustration.
69312
34.REMOVE FRONT DOOR LOCK OPEN ROD
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Disengage the snap to remove the front door lock open rod from the front door outside frame sub-assembly as shown in the illustration.
68210C
35.REMOVE FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY
68620
36.REMOVE FRONT DOOR CHECK ASSEMBLY
Remove the 3 bolts and front door check assembly.
37.REMOVE FRONT DOOR DIVISION BAR SEAL
Remove the 3 clips.
Remove the front door division bar seal.
67862
38.REMOVE FRONT DOOR WEATHERSTRIP
| *a | Clip (A) |
Disengage the 3 clips (A) and other clips to remove the front door weatherstrip.
39.REMOVE CUSHION
Disengage the claws to remove the 2 cushions.
67837B
40.REMOVE FRONT DOOR DUST PROOF SEAL
Disengage the claws to remove the 3 front door dust proof seals.
41.REMOVE HOLE PLUG
Remove the 3 hole plugs.
42.REMOVE HOLE PLUG
Remove the 2 hole plugs.