1.INSPECT TIRES
Inspect the tires for wear and proper inflation pressure.
| Tire Size | Front
kPa (kgf/cm2, psi) |
Rear
kPa (kgf/cm2, psi) |
|---|---|---|
|
*1: for driving under 160 km/h (99 mph) *2: for driving at 160 km/h (99 mph) or over *3: for driving under 200 km/h (124 mph) *4: for driving at 200 km/h (124 mph) or over |
||
| 175/70R14 84S | 250 (2.5, 36) | 240 (2.4, 35) |
| 185/60R15 84H | 230 (2.3, 33) | 220 (2.2, 32) |
| 185/65R15 88H | 230 (2.3, 33)*1
250 (2.5, 36)*2 |
220 (2.2, 32)*1
240 (2.4, 35)*2 |
| 280 (2.8, 41) | 280 (2.8, 41) | |
| 185/55R16 83V | 220 (2.2, 32)*1
230 (2.3, 33)*2 |
210 (2.1, 30)*1
220 (2.2, 32)*2 |
| 195/55R16 87V | 220 (2.2, 32)*1
240 (2.4, 35)*2 |
200 (2.0, 29)*1
220 (2.2, 32)*2 |
| 205/45R17 84W | 220 (2.2, 32) | 200 (2.0, 29) |
| 225/40R18 88W | 220 (2.2, 32)*3
250 (2.5, 36)*4 |
200 (2.0, 29)*3
230 (2.3, 33)*4 |
| 225/40ZR18 (92Y) | 220 (2.2, 32) | 200 (2.0, 29) |
For 185/65R15 88H tire, 2 different values of pressure are available. Refer to the tire pressure information label on the vehicle.
| Tire Size | kPa (kgf/cm2, psi) |
|---|---|
| T125/70D16 96M | 420 (4.2, 60) |
Perform initialization.
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION
Tire pressure adjustment method when warm:
On the GTS screen, display "Tire Inflation Pressure" of Data List.
Adjust the tire pressure so that the displayed value is equal to the set pressure.
Perform initialization and check that initialization completes.
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION
Check and record the value of the Data List item "Temperature in Tire". (Ts)
Check and record the ambient temperature during tire pressure adjustment. (Tm)
Readjust the tire pressure according to the difference between the tire internal temperature (Ts) and the ambient temperature (Tm). (P)
Tire internal temperature: Ts, Ambient temperature: Tm, Tire pressure readjustment value: P
P = (Specified Pressure) + (Ts - Tm)
Check the pressure adjustment value with the Data List item "Tire Inflation Pressure".
Check the tire pressure warning system for the relationship between the inflation pressure and tire pressure warning pressure.
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Using a dial indicator, check the runout of the tires.
1.4 mm (0.0551 in.)
2. ROTATE TIRES
Remove the wheel assembly.
|
Front |
Rotate the tires as shown in the illustration.
Install the wheel assembly.
Perform initialization.
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION
3.INSPECT AND ADJUST WHEEL BALANCE (for TMC Made)
Inspect and adjust the off-the-car balance.
for Steel Wheel:
8.0 g (0.0176 lb)
Use clip-on type balance weights for both the inner and outer side.
If the tires vibrate even after the off-the-car balance adjustment, adjust the wheel balance with on-the-car balancing as necessary.
| *a | 25 mm (0.984 in.) |
for G16E-GTS:
8.0 g (0.0176 lb)
Use a cleaning detergent to remove dirt, oil and water from the surface where the balance weight is to be adhered.
Do not touch the adhesive surface of the balance weight.
Adhere a stick-on type balance weight to the flat surface*a shown in the illustration.
Push the balance weight with your finger to securely adhere it to the desired position.
Do not reuse balance weights.
Use only TOYOTA genuine stick-on type balance weights or equivalent.
Use stick-on type balance weights for both the inner and outer side.
If the tires vibrate even after the off-the-car balance adjustment, adjust the wheel balance with on-the-car balancing as necessary.
| *a | 25 mm (0.984 in.) |
except G16E-GTS:
8.0 g (0.0176 lb)
Use a cleaning detergent to remove dirt, oil and water from the surface where the balance weight is to be adhered.
Do not touch the adhesive surface of the balance weight.
Adhere a stick-on type balance weight to the flat surface*a shown in the illustration.
Push the balance weight with your finger to securely adhere it to the desired position.
Do not reuse balance weights.
Use only TOYOTA genuine stick-on type balance weights or equivalent.
Use clip-on type balance weights for the inner side, and stick-on type balance weights for the outer side.
If the tires vibrate even after the off-the-car balance adjustment, adjust the wheel balance with on-the-car balancing as necessary.
4.INSPECT AND ADJUST WHEEL BALANCE (for TMMF Made)
Inspect and adjust the off-the-car balance.
for Steel Wheel:
8.0 g (0.0176 lb)
Use clip-on type balance weights for both the inner and outer side.
If the tires vibrate even after the off-the-car balance adjustment, adjust the wheel balance with on-the-car balancing as necessary.
| *a | 25 mm (0.984 in.) |
for 15 inch Aluminum Wheel:
8.0 g (0.0176 lb)
Use a cleaning detergent to remove dirt, oil and water from the surface where the balance weight is to be adhered.
Do not touch the adhesive surface of the balance weight.
Adhere a stick-on type balance weight to the flat surface*a shown in the illustration.
Push the balance weight with your finger to securely adhere it to the desired position.
Do not reuse balance weights.
Use only TOYOTA genuine stick-on type balance weights or equivalent.
Use stick-on type balance weights for both the inner and outer side.
If the tires vibrate even after the off-the-car balance adjustment, adjust the wheel balance with on-the-car balancing as necessary.
| *a | 25 mm (0.984 in.) |
except 15 inch Aluminum Wheel:
8.0 g (0.0176 lb)
Use a cleaning detergent to remove dirt, oil and water from the surface where the balance weight is to be adhered.
Do not touch the adhesive surface of the balance weight.
Adhere a stick-on type balance weight to the flat surface*a shown in the illustration.
Push the balance weight with your finger to securely adhere it to the desired position.
Do not reuse balance weights.
Use only TOYOTA genuine stick-on type balance weights or equivalent.
Use clip-on type balance weights for the inner side, and stick-on type balance weights for the outer side.
If the tires vibrate even after the off-the-car balance adjustment, adjust the wheel balance with on-the-car balancing as necessary.
5.INSPECT FRONT AXLE HUB BEARING
for TMC Made G16E-GTS:
Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB (for TMC Made G16E-GTS)>ON-VEHICLE INSPECTION
for TMC Made except G16E-GTS:
Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB (for TMC Made except G16E-GTS)>ON-VEHICLE INSPECTION
for TMMF Made:
Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB (for TMMF Made)>ON-VEHICLE INSPECTION
6.INSPECT REAR AXLE HUB BEARING
for TMC Made G16E-GTS:
Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB (for TMC Made G16E-GTS)>ON-VEHICLE INSPECTION
for TMC Made except G16E-GTS:
Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB (for TMC Made except G16E-GTS)>ON-VEHICLE INSPECTION
for TMMF Made:
Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB (for TMMF Made)>ON-VEHICLE INSPECTION