Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE HUB (for TMMF Made) › 2020.07–2021.11
RM36W0E _52 Drivetrain _087260 AXLE AND DIFFERENTIAL _0430773 REAR AXLE HUB(for TMMF Made) G

AXLE AND DIFFERENTIAL  REAR AXLE HUB(for TMMF Made)  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 42431D 2.REMOVE REAR BRAKE DRUM SUB-ASSEMBLY (for Rear Drum Brake)

Hide 3.SEPARATE NO. 2 PARKING BRAKE WIRE ASSEMBLY (for Rear Disc Brake)

Hide 4.SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY (for Rear Disc Brake)

Hide 5.REMOVE REAR DISC (for Rear Disc Brake)

Hide 6.INSPECT REAR AXLE HUB BEARING LOOSENESS (for Rear Drum Brake)

a.
C427827

Using a dial indicator with magnetic base, check for looseness near the center of the rear axle hub and bearing assembly.

Maximum Looseness:

0.05 mm (0.00197 in.)


NOTICE:
·

Ensure that the dial indicator is set perpendicular to the measurement surface.

·

Keep the magnet of the dial indicator away from the rear axle hub and bearing assembly.



HINT:

If the looseness exceeds the maximum, replace the rear axle hub and bearing assembly.



Hide 7.INSPECT REAR AXLE HUB BEARING LOOSENESS (for Rear Disc Brake)

a.
C427828

Using a dial indicator with magnetic base, check for looseness near the center of the rear axle hub and bearing assembly.

Maximum Looseness:

0.05 mm (0.00197 in.)


NOTICE:
·

Ensure that the dial indicator is set perpendicular to the measurement surface.

·

Keep the magnet of the dial indicator away from the rear axle hub and bearing assembly.



HINT:

If the looseness exceeds the maximum, replace the rear axle hub and bearing assembly.



Hide 8.INSPECT REAR AXLE HUB RUNOUT (for Rear Drum Brake)

C427829

a.

Using a dial indicator with magnetic base, check for runout on the surface of the rear axle hub and bearing assembly outside the rear axle hub bolts.

Maximum Runout:

0.07 mm (0.00276 in.)


NOTICE:
·

Ensure that the dial indicator is set perpendicular to the measurement surface.

·

Make sure to install the tip of the dial indicator towards the outside of the rear axle hub bolts.

·

Keep the magnet of the dial indicator away from the rear axle hub and bearing assembly.



HINT:

If the runout exceeds the maximum, replace the rear axle hub and bearing assembly.



Hide 9.INSPECT REAR AXLE HUB RUNOUT (for Rear Disc Brake)

C427830

a.

Using a dial indicator with magnetic base, check for runout on the surface of the rear axle hub and bearing assembly outside the rear axle hub bolts.

Maximum Runout:

0.07 mm (0.00276 in.)


NOTICE:
·

Ensure that the dial indicator is set perpendicular to the measurement surface.

·

Make sure to install the tip of the dial indicator towards the outside of the rear axle hub bolts.

·

Keep the magnet of the dial indicator away from the rear axle hub and bearing assembly.



HINT:

If the runout exceeds the maximum, replace the rear axle hub and bearing assembly.



Hide 42431D 10.INSTALL REAR BRAKE DRUM SUB-ASSEMBLY (for Rear Drum Brake)

Hide 11.INSTALL REAR DISC (for Rear Disc Brake)

Hide 12.INSTALL REAR DISC BRAKE CALIPER ASSEMBLY (for Rear Disc Brake)

Hide 13.CONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY (for Rear Disc Brake)

Hide 14.INSTALL REAR WHEEL