The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the brake actuator assembly removal/installation are shown below.
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM (for M15A-FKS)
for HFC-134a(R134a):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>REPLACEMENT
for HFO-1234yf(R1234yf):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFO-1234yf(R1234yf))>REPLACEMENT
3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
for 1KR-FE:
Click hereGeneral>MAINTENANCE>1KR-FE AUXILIARY BATTERY>REMOVAL
for M15A-FKS:
Click hereGeneral>MAINTENANCE>M15A-FKS AUXILIARY BATTERY>REMOVAL
4.DRAIN BRAKE FLUID
If brake fluid leaks onto any painted surface, immediately wash it off.
5.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
55815E
6.REMOVE FRONT NO. 1 VENTILATOR SEAL
55734A
7.REMOVE WATER GUARD PLATE RH
55701J
8.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY
51451A
9.REMOVE CENTER ENGINE UNDER COVER (for M15A-FKS)
55225C
10.REMOVE DASH PANEL HEAT INSULATOR (for M15A-FKS)
Remove the nut.
Remove the 2 nuts and dash panel heat insulator.
88707
11.REMOVE SUCTION PIPE SUB-ASSEMBLY (for M15A-FKS)
|
Rotate in this Direction |
Remove the bolt and rotate the hook connector as shown in the illustration.
Disconnect the suction pipe sub-assembly from the air conditioning unit assembly.
Disengage the clamp to separate the suction pipe sub-assembly.
Remove the O-ring from the suction pipe sub-assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
88710E
12.REMOVE AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY (for M15A-FKS)
|
Remove in this Direction |
Disconnect the air conditioning tube and accessory assembly from the air conditioning unit assembly.
Disengage the clamp to separate the air conditioning tube and accessory assembly.
Remove the O-ring from the air conditioning tube and accessory assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
13.REMOVE BRAKE ACTUATOR WITH BRACKET
for M15A-FKS:
|
Move in this Direction |
Move aside the suction pipe sub-assembly and air conditioner tube and accessory assembly as shown in the illustration.
Do not apply excessive force to the suction pipe sub-assembly and air conditioner tube and accessory assembly.
|
Release the lock lever |
|
Disconnect the connector |
Release the lock lever and disconnect the connector from the brake actuator assembly.
Be careful not to allow any brake fluid to enter the connector.
| *a | From 1st Chamber of Brake Master Cylinder Sub-assembly |
| *b | From 2nd Chamber of Brake Master Cylinder Sub-assembly |
| *c | To Front Wheel Cylinder Assembly RH |
| *d | To Rear Wheel Cylinder Assembly LH |
| *e | To Rear Wheel Cylinder Assembly RH |
| *f | To Front Wheel Cylinder Assembly LH |
Use tags or make a memo to identify the places to reconnect the brake lines.
Using a union nut wrench, disconnect the 6 brake lines from the brake actuator assembly.
Do not kink or damage the brake lines.
Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.
for M15A-FKS:
Disengage the 5 clamps to remove the No. 2 brake tube clamp from the brake lines.
Do not kink or damage the brake lines.
Disengage the 4 clamps to remove the No. 1 brake tube clamp from the brake lines.
Disengage the clamp and remove the No. 1 brake tube clamp from the vehicle body.
Remove the 2 nuts.
Remove the bolt and brake actuator with bracket.
Do not kink or damage the brake lines.
Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.
Be careful not to allow any brake fluid to enter the connector.
Do not hold the brake actuator assembly by the connector.
Do not drop the brake actuator with bracket when carrying it.
Remove the brake actuator with bracket while avoiding the brake lines.
44510
14.REMOVE BRAKE ACTUATOR ASSEMBLY
Remove the 3 bolts and brake actuator assembly from the brake actuator bracket assembly.
Do not hold the brake actuator assembly by the connector.
Be careful not to allow any brake fluid to enter the connector.
Do not drop the brake actuator assembly when carrying it.
44547B
15.REMOVE BRAKE ACTUATOR BRACKET CUSHION
| *1 | No. 1 Brake Actuator Case Collar |
| *2 | Brake Actuator Bracket Cushion |
| *3 | Brake Actuator Bracket Assembly |
Remove the 3 No. 1 brake actuator case collars from the brake actuator bracket cushion.
Remove the 3 brake actuator bracket cushions from the brake actuator bracket assembly.