Home › Suspension › FRONT SUSPENSION › FRONT SUSPENSION MEMBER (except G16E-GTS) › 2020.09–2021.11
RM36W0E _53 Suspension _087263 FRONT SUSPENSION _0447911 FRONT SUSPENSION MEMBER(except G16E-GTS) A

FRONT SUSPENSION  FRONT SUSPENSION MEMBER(except G16E-GTS)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front suspension crossmember sub-assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Front wheel alignment adjustment for HV Model:
1.

Perform "Reset Memory"

2.

Perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for TMC Made:
(Click here)
for TMMF Made:
(Click here)
for Gasoline Model:
Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for TMC Made:
(Click here)
for TMMF Made:
(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)

CAUTION:
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


PROCEDURE

Hide 1.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 2. SECURE STEERING WHEEL

a.
C440311

Secure the steering wheel with the seat belt in order to prevent rotation.

HINT:

This operation is useful to prevent damage to the spiral cable.



Hide 45259A 3.REMOVE COLUMN HOLE COVER SILENCER SHEET (for LHD)

Hide 45259A 4.REMOVE COLUMN HOLE COVER SILENCER SHEET (for RHD)

Hide 45260 5.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 6.REMOVE FRONT WHEELS

Hide 51451A 7.REMOVE CENTER ENGINE UNDER COVER

a.

w/ Center Engine Under Cover for Full Cover Type:

i.
C431863

Remove the 4 bolts, 4 screws, 9 clips and center engine under cover from the vehicle body.



b.

w/ Center Engine Under Cover for Half Cover Type:

i.
C438026

Remove the 4 bolts, 4 screws, 7 clips and center engine under cover from the vehicle body.



Hide 51442C 8.REMOVE ENGINE UNDER COVER LH

a.

w/ Center Engine Under Cover for Full Cover Type, w/ Center Engine Under Cover for Half Cover Type:

i.
A461618

Remove the 2 clips and engine under cover LH from the vehicle body.



b.

w/o Center Engine Under Cover:

i.
C437618

Remove the 3 clips and engine under cover LH from the vehicle body.



Hide 51441C 9.REMOVE ENGINE UNDER COVER RH

HINT:

Perform the same procedure as for the LH side.


Hide 53876A 10.SEPARATE FRONT FENDER LINER LH (w/ Engine Under Cover Assembly)

a.
C429669

Remove the 2 screws and separate the front fender liner LH.


Hide 53875A 11.SEPARATE FRONT FENDER LINER RH (w/ Engine Under Cover Assembly)

HINT:

Perform the same procedure as for the LH side.


Hide 51447D 12.REMOVE CENTER NO. 4 ENGINE UNDER COVER (for TMC Made)

a.
C431773

Remove the 2 bolts, 2 nuts and center No. 4 engine under cover from the vehicle body.


Hide 51447D 13.REMOVE CENTER NO. 4 ENGINE UNDER COVER (for TMMF Made)

a.

except 1KR-FE:

i.
C436131

Remove the 4 bolts and center No. 4 engine under cover from the vehicle body.



Hide 48810 14.SEPARATE FRONT STABILIZER LINK ASSEMBLY LH

a.
C436132

Remove the nut and separate the front stabilizer link assembly LH from the front stabilizer bar.

NOTICE:

Do not damage the boot of the ball joint.


HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.



Hide 48820B 15.SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45047 16.SEPARATE TIE ROD END SUB-ASSEMBLY LH (for TMC Made)

a.
C428598

Remove the cotter pin and nut.


b.
C428599N01
2.406,1.531 2.677,1.219 false 2.094,1.438 2.552,1.635 0.458,0.198 10 false SST

Install SST to the tie rod end sub-assembly LH.

SST
09960-20010  (09961-02060)

NOTICE:

Make sure that the lower ends of the tie rod end sub-assembly LH and SST are aligned.



c.

Secure SST using a string.

NOTICE:

Be sure to tighten the string firmly to secure SST to the steering knuckle LH to prevent SST from falling off.



d.

Using SST, separate the tie rod end sub-assembly LH from the steering knuckle LH.

SST
09960-20010  (09961-02010)

C428600C01
1.083,2.75 1.25,2.583 false 0.333,1.083 0.583,1.083 true 3.333,2.917 3.333,2.667 false 0.167,1 0.333,1.167 0.167,0.167 10 true *a 6.583,0.844 6.896,1 0.313,0.156 10 false *c 2.667,1.083 2.979,1.24 0.313,0.156 10 false *d 0.26,2.833 0.667,3.167 0.406,0.333 10 false A 0.25,3.042 0.656,3.375 0.406,0.333 10 false B 5.521,2.49 5.833,2.646 0.313,0.156 10 false *b 5.5,2.771 5.813,2.927 0.313,0.156 10 false *b 1.271,2.417 1.583,2.573 0.313,0.156 10 false *d 3.188,2.917 3.583,3.083 0.396,0.167 10 false SST
*a String *b Molybdenum Grease Application Area
*c Place wrench here *d Center Nut
V113147

Turn - -


CAUTION:

Apply molybdenum grease to the bolt threads and the tip of SST.


NOTICE:
·

Be sure to tighten the string firmly to secure SST to the steering knuckle LH to prevent SST from falling off.

·

Install SST with the center nut so that (A) and (B) shown in the illustration are parallel. Otherwise, the ball joint dust cover may be damaged.

·

Be sure to place the wrench on the part shown in the illustration.

·

Do not damage the front disc brake dust cover.

·

Do not damage the ball joint dust cover.

·

Do not damage the steering knuckle LH.




Hide 45047 17.SEPARATE TIE ROD END SUB-ASSEMBLY LH (for TMMF Made)

a.
C428597C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claw to remove the steering knuckle seal as shown in the illustration.


b.
C428598

Remove the cotter pin and nut.


c.
C428599N01
2.406,1.531 2.677,1.219 false 2.094,1.438 2.552,1.635 0.458,0.198 10 false SST

Install SST to the tie rod end sub-assembly LH.

SST
09960-20010  (09961-02060)

NOTICE:

Make sure that the lower ends of the tie rod end sub-assembly LH and SST are aligned.



d.

Secure SST using a string.

NOTICE:

Be sure to tighten the string firmly to secure SST to the steering knuckle LH to prevent SST from falling off.



e.

Using SST, separate the tie rod end sub-assembly LH from the steering knuckle LH.

SST
09960-20010  (09961-02010)

C428600C01
1.083,2.75 1.25,2.583 false 0.333,1.083 0.583,1.083 true 3.333,2.917 3.333,2.667 false 0.167,1 0.333,1.167 0.167,0.167 10 true *a 6.583,0.844 6.896,1 0.313,0.156 10 false *c 2.667,1.083 2.979,1.24 0.313,0.156 10 false *d 0.26,2.833 0.667,3.167 0.406,0.333 10 false A 0.25,3.042 0.656,3.375 0.406,0.333 10 false B 5.521,2.49 5.833,2.646 0.313,0.156 10 false *b 5.5,2.771 5.813,2.927 0.313,0.156 10 false *b 1.271,2.417 1.583,2.573 0.313,0.156 10 false *d 3.188,2.917 3.583,3.083 0.396,0.167 10 false SST
*a String *b Molybdenum Grease Application Area
*c Place wrench here *d Center Nut
V113147

Turn - -


CAUTION:

Apply molybdenum grease to the bolt threads and the tip of SST.


NOTICE:
·

Be sure to tighten the string firmly to secure SST to the steering knuckle LH to prevent SST from falling off.

·

Install SST with the center nut so that (A) and (B) shown in the illustration are parallel. Otherwise, the ball joint dust cover may be damaged.

·

Be sure to place the wrench on the part shown in the illustration.

·

Do not damage the front disc brake dust cover.

·

Do not damage the ball joint dust cover.

·

Do not damage the steering knuckle LH.




Hide 45046 18.SEPARATE TIE ROD END SUB-ASSEMBLY RH (for TMC Made)

HINT:

Perform the same procedure as for the LH side.


Hide 45046 19.SEPARATE TIE ROD END SUB-ASSEMBLY RH (for TMMF Made)

HINT:

Perform the same procedure as for the LH side.


Hide 48069 20.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH (for TMC Made)

Hide 48069 21.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH (for TMMF Made)

Hide 48068 22.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH (for TMC Made)

HINT:

Perform the same procedure as for the LH side.


Hide 48068 23.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH (for TMMF Made)

HINT:

Perform the same procedure as for the LH side.


Hide 57543C 24.REMOVE CENTER NO. 1 FLOOR BRACE (for 1KR-FE)

Hide 17410 25.REMOVE FRONT EXHAUST PIPE ASSEMBLY (for 1KR-FE)

Hide 51201 26.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.
C427905

except 1KR-FE:

i.

Remove the bolt and separate the wiring harness clamp bracket from the front suspension crossmember sub-assembly.



b.
C427882C01
1,2.25 1.167,2.25 1.167,2.25 1.5,1.667 true 1.271,0.896 1.396,0.896 1.396,0.896 1.802,1.25 true 1.052,0.823 1.292,0.99 0.24,0.167 10 true *b 0.823,2.167 1.135,2.323 0.313,0.156 10 false *a
*a Transmission Jack
*b Wooden Block
V100135

Front of the Vehicle
V100155

Wooden block placement location


Using a transmission jack and a wooden block, support the engine assembly with transaxle.

CAUTION:
C427884

·

Support the engine assembly with transaxle until the front suspension crossmember sub-assembly is installed.

·

If the support is removed before the front suspension crossmember sub-assembly is installed, the engine assembly with transaxle may drop.




c.
C427885

Remove the bolt and separate the engine moving control rod.


d.

Support the front suspension crossmember sub-assembly with an engine lifter using 4 attachments or equivalent tools as shown in the illustration.

C432278C01
3.083,1.438 3.375,1.635 3.375,1.635 3.542,1.635 true 1,1.583 3,1.583 3,1.583 3,1.083 true 2.729,1.583 2.729,1.115 true 2.021,1.583 2.021,1.25 true 1.615,1.583 1.615,1.302 true 3.583,1.542 3.896,1.698 0.313,0.156 10 false *a 0.792,1.479 1.104,1.635 0.313,0.156 10 false *b
*a Engine Lifter *b Attachment
V100155

Attachment placement location - -


CAUTION:
·
C320210

The front suspension crossmember sub-assembly is a very heavy component. Make sure that it is supported securely.

·

If the front suspension crossmember sub-assembly is not securely supported, it may drop, resulting in serious injury.



NOTICE:

Use attachments to keep the front suspension crossmember sub-assembly level.



e.
C432279

Remove the 10 bolts and front suspension crossmember sub-assembly.


f.

Slowly lower the front suspension crossmember sub-assembly.

NOTICE:
·

When lowering the front suspension crossmember sub-assembly, be careful not to damage the vehicle body or other components installed to the vehicle.

·

Make sure that the front suspension crossmember sub-assembly not hit the protrusion of the reinforcement.




Hide 51228G 27.REMOVE FRONT SUSPENSION MEMBER PLATE (w/ Plate)

a.
C437619

Remove the 2 bolts and suspension member plate from the front suspension member sub-assembly.


Hide 12363A 28.REMOVE ENGINE MOVING CONTROL ROD

a.
C427890

Remove the bolt and engine moving control rod from the front suspension crossmember sub-assembly.


Hide 48069 29.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.
C428505C01
0.01,0.104 0.26,0.302 0.25,0.198 12 true *A 0.01,2.385 0.281,2.583 0.271,0.198 12 true *B
*A for TMC Made
*B for TMMF Made


Remove the 2 bolts, nut and front lower No. 1 suspension arm sub-assembly LH from the front suspension crossmember sub-assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



Hide 48068 30.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 31.REMOVE STEERING LINK ASSEMBLY

Hide 48811 32.REMOVE FRONT STABILIZER BAR