Make sure to use Toyota Genuine Windshield Glass Adhesive (High Modulus Type) or equivalent.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
62720A
1.CLEAN QUARTER WINDOW ASSEMBLY
Clean the outer circumference of a new quarter window assembly with a non-residue solvent.
Do not touch the quarter window assembly surface after cleaning it.
62720A
2.INSTALL QUARTER WINDOW ASSEMBLY
Clean and shape the contact surface of the vehicle body.
|
Adhesive |
Using a knife, cut away excess adhesive on the contact surface of the vehicle body as shown in the illustration.
Be careful not to damage the vehicle body.
Leave as much adhesive on the vehicle body as possible.
Clean the contact surface of the vehicle body with a piece of cloth saturated with non-residue solvent.
Install suction cups to the quarter window assembly.
Using a brush or sponge, coat the installation surfaces on the vehicle body with body primer.
Do not coat the adhesive with body primer.
Do not apply too much body primer.
Allow the body primer to dry for 3 minutes or more.
Throw away any leftover body primer.
Using a brush or a sponge, apply glass primer to the contact surface of a new quarter window assembly as shown in the illustration.
Do not apply too much glass primer.
Allow the glass primer to dry for 3 minutes or more.
Throw away any leftover glass primer.
| *a | Back Side of Quarter Window Assembly | - | - |
|
Glass Primer | - | - |
| Area | Dimension |
|---|---|
| a | 11 mm (0.433 in.) or more |
| b | 19 mm (0.748 in.) or more |
| c | 11 mm (0.433 in.) or more |
Apply adhesive to the quarter window assembly.
Toyota Genuine Windshield Glass Adhesive (High modulus type) or equivalent
| *a | Sealer Gun |
| *b | Cartridge Nozzle |
|
Adhesive |
Cut off the tip of the cartridge nozzle as shown in the illustration.
| Area | Dimension |
|---|---|
| a | 12 to 15 mm (0.472 to 0.591 in.) |
| b | 8.0 to 11 mm (0.315 to 0.433 in.) |
Load the sealer gun with the cartridge.
Apply adhesive to the glass as shown in the illustration.
| *a | Back Side of Quarter Window Assembly | - | - |
|
Adhesive | - | - |
| Area | Dimension |
|---|---|
| a | 4.0 mm (0.157 in.) |
| b | 4.0 mm (0.157 in.) |
| c | 4.0 mm (0.157 in.) |
Install the quarter window assembly to the vehicle body.
1. Using suction cups, engage the clips to install the quarter window assembly.
Check that the clips are engaged to the vehicle body correctly.
Check the clearance between the vehicle body and quarter window assembly.
Lightly press the outer surface of the quarter window assembly to ensure that the quarter window assembly is securely fit to the vehicle body.
Press the glass with a force of 98 N (10 kgf, 22.0 lbf) or more.
Using a scraper, remove any excess or protruding adhesive.
Hold the quarter window assembly using protective tape until the applied adhesive becomes hard.
Follow the instructions supplied by the adhesive manufacturer or in the corresponding instruction manual for the minimum amount of time necessary to wait before driving the vehicle.
62362
3.INSTALL FRONT ROOF SIDE RAIL WEATHERSTRIP RETAINER
62452
4.INSTALL ROOF SIDE INNER GARNISH
62412B
5.INSTALL CENTER PILLAR UPPER GARNISH
62472A
6.INSTALL INNER ROOF SIDE GARNISH
7.INSPECT FOR LEAK
After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.
If water leaks into the cabin, allow the water to dry and add adhesive.
Remove the protective tape.