Home › Power Source / Network › G16E-GTS (BATTERY / CHARGING) › CHARGING SYSTEM › from 2020.09
RM36W0E _57 Power Source / Network _095208 G16E-GTS BATTERY / CHARGING _0447332 CHARGING SYSTEM C

G16E-GTS BATTERY / CHARGING  CHARGING SYSTEM  P161A87  Lost Communication with Alternator Missing Message  


DESCRIPTION

The ECM communicates with the generator assembly via LIN communication. If a LIN communication error is detected, the ECM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P161A87 Lost Communication with Alternator Missing Message Generator assembly or ECM communication stops for approximately 17 minutes or more with the ignition switch ON
(1 trip detection logic)
·

Wire harness or connector

·

Generator assembly

·

ECM


Comes on SAE Code: P161A

WIRING DIAGRAM

A427236E28
0.458,0.646 1.375,1.302 0.917,0.656 10 false from Auxiliary Battery 1.563,0.865 2.479,1.104 0.917,0.24 10 false BATT-S NO. 1 2.5,0.625 2.635,0.833 0.135,0.208 10 false 3 2.677,0.708 2.927,0.938 0.25,0.229 10 false +B 3.729,0.719 3.979,0.948 0.25,0.229 10 false LIN 4.063,0.573 4.313,0.802 0.25,0.229 10 false 2 2.615,1.167 3,1.427 0.385,0.26 10 false O68 2.615,1.323 4.729,1.552 2.115,0.229 10 false Battery State Sensor Assembly 2.625,2.656 3.01,2.917 0.385,0.26 10 false D53 2.635,2.833 4.927,3.083 2.292,0.25 9 false Generator Assembly 1.083,3.177 3.198,3.406 2.115,0.229 10 false : LIN Communication Line 5.854,0.719 6.146,0.958 0.292,0.24 10 false LIN 5.583,0.542 5.833,0.771 0.25,0.229 10 false 62 5.802,1.802 6.271,2.031 0.469,0.229 10 false D104 5.802,1.979 6.313,2.208 0.51,0.229 10 false ECM 3.719,2.167 4.229,2.396 0.51,0.229 10 false LIN 4.052,2.052 4.302,2.281 0.25,0.229 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before replacing the ECM, refer to Service Bulletin.



PROCEDURE

1.CHECK CHARGING SYSTEM

OK

2.CHECK HARNESS AND CONNECTOR (ECM - GENERATOR ASSEMBLY)

NG

REPAIR OR REPLACE CHARGING SYSTEM

2.CHECK HARNESS AND CONNECTOR (ECM - GENERATOR ASSEMBLY)

Pre-procedure1

a.

Disconnect the D104 ECM connector.


b.

Disconnect the D53 generator assembly connector.


c.

Disconnect the O68 battery state sensor assembly connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
O68-2 (LIN) or D53-2 (LIN) - D104-62 (LIN) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
O68-2 (LIN), D53-2 (LIN) or D104-62 (LIN) - Body ground Ignition switch off
(while LIN communication stopped)
10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CLEAR DTC

Pre-procedure1

a.

Check for DTCs using the GTS, and then write them down.

Powertrain > Engine > Trouble Codes
50001 372

Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Post-procedure1

c.

Turn the ignition switch off and wait 30 seconds.


Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT
4.CHECK DTC OUTPUT

Pre-procedure1

a.

Start the engine.


b.

Allow the engine to idle for approximately 17 minutes or more.


Procedure1

c.

Using the GTS, check for DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Post-procedure1

d.

None


Result:
Result Proceed to
Only P161A87 is output A
P161A87 and P162B87 are output B
DTCs are not output C



A

REPLACE GENERATOR WITH REGULATOR ASSEMBLY

B

C