Home › Power Source / Network › G16E-GTS (BATTERY / CHARGING) › CHARGING SYSTEM › from 2020.09
RM36W0E _57 Power Source / Network _095208 G16E-GTS BATTERY / CHARGING _0447332 CHARGING SYSTEM C

G16E-GTS BATTERY / CHARGING  CHARGING SYSTEM  P058A01  Battery Monitor Module General Electrical Failure  


DESCRIPTION

The battery state sensor assembly detects the voltage, current and temperature of the auxiliary battery. The charging condition is calculated from the voltage and current and output to the ECM. The ECM sends an instruction to generate voltage to the generator assembly based on that signal. Also, the auxiliary battery temperature is calculated from the change in the resistance value of the thermistor built into the battery state sensor assembly and output to the ECM. The ECM reduces the charging current when the auxiliary battery is hot and protects the auxiliary battery based on this signal.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P058A01 Battery Monitor Module General Electrical Failure Any of the following conditions is met with the ignition switch ON. (1 trip detection logic):
·

Current value is 999.939 A or higher or -1000 A or less for 3.2 seconds or more.

·

Difference between maximum and minimum current value is 0.0305 A or less for 100 seconds or more.

·

Current detection circuit malfunction condition is received.

·

Auxiliary battery temperature is 105°C or higher or -40°C or lower for 3.2 seconds or more.

·

Temperature detection circuit malfunction condition is received.

·

Voltage value remains at 15.98 V or higher or 6.0 V or less for 3.2 seconds or more.

·

Voltage detection circuit malfunction condition is received.

·

Battery state sensor assembly internal memory write malfunction (battery identification information) occurs.


·

Battery state sensor assembly

·

Wire harness or connector

·

Auxiliary battery


Does not come on SAE Code: P058A

WIRING DIAGRAM

A475010E04
6.083,2.052 6.646,2.385 0.563,0.333 10 false ECM 6.073,1.885 6.531,2.083 0.458,0.198 10 false D104 5.823,0.698 6.281,0.896 0.458,0.198 10 false LIN 5.531,0.51 5.99,0.708 0.458,0.198 10 false 62 4.26,0.708 4.719,0.906 0.458,0.198 10 false LIN 4.635,0.51 5.094,0.708 0.458,0.198 10 false 2 3.042,0.375 3.5,0.573 0.458,0.198 10 false +B 2.833,0.281 3.292,0.479 0.458,0.198 10 false 3 0.729,1.146 1.875,1.354 1.146,0.208 10 false INP STD NO. 1-3 0.938,2.438 2.615,2.76 1.677,0.323 10 false Auxiliary Battery 2.99,1.51 5.208,1.865 2.219,0.354 10 false Battery State Sensor Assembly 2.99,1.302 3.448,1.5 0.458,0.198 10 false O68 0.74,3.292 2.771,3.594 2.031,0.302 10 false : LIN Communication Line 0.76,1.719 2.01,2.063 1.25,0.344 10 false ENG 3.052,0.979 3.667,1.177 0.615,0.198 10 false RBAT 2.833,0.885 2.99,1.083 0.156,0.198 10 false 1 0.969,0.563 1.844,0.781 0.875,0.219 10 false R/B BATT 1.917,0.542 3.052,0.74 1.135,0.198 10 false BATT-S NO. 1 1.979,1.156 2.979,1.406 1,0.25 10 false ECU-B NO. 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When P162B87 (Lost Communication with Battery Monitor Module Missing Message) is output at the same time, perform the inspection for P162B87 (Lost Communication with Battery Monitor Module Missing Message) first.

Click herePower Source / Network>G16E-GTS (BATTERY / CHARGING)>CHARGING SYSTEM>P162B87



PROCEDURE

1.CHECK BATTERY STATE SENSOR ASSEMBLY INSTALLATION

OK

2.CHECK CHARGING SYSTEM

NG

INSTALL BATTERY STATE SENSOR ASSEMBLY CORRECTLY

2.CHECK CHARGING SYSTEM

OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CHARGING SYSTEM

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

Pre-procedure1

a.

Disconnect the battery state sensor assembly connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O68-3 (+B) - Body ground Always 11 to 14 V
O68-1 (RBAT) - Body ground Always 11 to 14 V



Post-procedure1

c.

None


Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR