Home › Power Source / Network › G16E-GTS (BATTERY / CHARGING) › CHARGING SYSTEM › from 2020.09
RM36W0E _57 Power Source / Network _095208 G16E-GTS BATTERY / CHARGING _0447332 CHARGING SYSTEM C

G16E-GTS BATTERY / CHARGING  CHARGING SYSTEM  P162B87  Lost Communication with Battery Monitor Module Missing Message  


DESCRIPTION

The ECM and battery state sensor assembly each detect reception malfunctions. A battery state sensor assembly reception malfunction detected by the battery state sensor assembly is sent to the ECM via LIN communication. If there is a malfunction in either the ECM or battery state sensor assembly, the ECM determines that there is a LIN communication malfunction and outputs a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P162B87 Lost Communication with Battery Monitor Module Missing Message Battery state sensor assembly or ECM communication stops for approximately 17 minutes or more with the ignition switch to ON
(1 trip detection logic)
·

Battery state sensor assembly

·

ECM

·

Wire harness or connector


Does not come on SAE Code: P162B

WIRING DIAGRAM

Refer to the wiring diagram for the P062049.

Click herePower Source / Network>G16E-GTS (BATTERY / CHARGING)>CHARGING SYSTEM>P062049

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK BATTERY STATE SENSOR ASSEMBLY INSTALLATION CONDITION

OK

2.CHECK CHARGING SYSTEM

NG

INSTALL BATTERY STATE SENSOR ASSEMBLY CORRECTLY

2.CHECK CHARGING SYSTEM

OK

3.CHECK HARNESS AND CONNECTOR (ECM - BATTERY STATE SENSOR ASSEMBLY)

NG

REPAIR OR REPLACE CHARGING SYSTEM

3.CHECK HARNESS AND CONNECTOR (ECM - BATTERY STATE SENSOR ASSEMBLY)

Pre-procedure1

a.

Disconnect the D104 ECM connector.


b.

Disconnect the O68 battery state sensor assembly connector.


c.

Disconnect the D53 generator assembly connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D104-62 (LIN) - O68-2 (LIN) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D104-62 (LIN), D53-2 (LIN) or O68-2 (LIN) - Body ground Ignition switch off
(while LIN communication stopped)
10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

Pre-procedure1

a.

Check that the battery state sensor assembly connector is securely connected.

OK:

The connector is securely connected.



b.

Disconnect the O68 battery state sensor assembly connector.


c.

Check the connector case and terminals for deformation or corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O68-3 (+B) - Body ground Always 11 to 14 V



Post-procedure1

e.

None


Result:
Result
OK
NG



OK

5.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CLEAR DTC

Pre-procedure1

a.

Check for DTCs using the GTS, and then write them down.

Powertrain > Engine > Trouble Codes
50001 372

Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Post-procedure1

c.

Turn the ignition switch off and wait 30 seconds.


Result:
Proceed to
NEXT



NEXT

6.READ OUTPUT DTC
6.READ OUTPUT DTC

Pre-procedure1

a.

Start the engine and wait 17 minutes or more.


Procedure1

b.

Using the GTS, read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Post-procedure1

c.

None


Result:
Result Proceed to
Only P162B87 is output A
P161A87 and P162B87 are output B
DTCs are not output C



A

B

C