Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS (for 3 Door) › from 2020.09
RM36W0E _59 Vehicle Exterior _088018 WINDOW / GLASS _0447338 WINDSHIELD GLASS(for 3 Door) A

WINDOW / GLASS  WINDSHIELD GLASS(for 3 Door)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also, the dynamic radar cruise control system, lane tracing assist system, road sign assist system, pre-collision system, front camera system or auto high beam system may not operate properly due to a difference in the transmissivity or black ceramic border.


PROCEDURE

Hide 56111 1.CLEAN WINDSHIELD GLASS

a.

When reusing the windshield glass:

i.
B106929

Using a scraper, remove any remaining adhesive dam and adhesive residue from the windshield glass.

NOTICE:

Be careful not to damage the windshield glass.



ii.

Clean the outer circumference of the windshield glass with a non-residue solvent.

NOTICE:
·

Do not touch the windshield glass surface after cleaning it.

·

Even if using a new windshield glass, clean it with a non-residue solvent.





Hide 56115C 2.INSTALL WINDSHIELD GLASS STOPPER

a.

Using a brush or sponge, coat the installation area of the 2 windshield glass stoppers with glass primer.

NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



b.

Install 2 new windshield glass stoppers to the windshield glass as shown in the illustration.

B590307C01
1.615,1.031 1.5,0.698 false 5.708,1.021 5.927,0.635 false 1.573,1.219 2.177,0.708 2.177,0.708 2.115,1.281 true 5.156,1.271 5.365,0.729 true 2.167,0.719 1.854,1.26 true 4.885,1.292 5.375,0.708 5.375,0.708 5.427,1.229 true 2.229,2.073 2.542,2.229 0.313,0.156 10 false *a 1.354,0.521 1.667,0.677 0.313,0.156 10 false *c 0.771,0.979 0.927,1.135 0.156,0.156 10 false a 5.344,0.521 5.656,0.677 0.313,0.156 10 false *b 6.323,0.969 6.479,1.125 0.156,0.156 10 false a 5.938,0.458 6.25,0.615 0.313,0.156 10 false *c 2.135,0.552 2.448,0.708 0.313,0.156 10 false *b
*a Back Side of Windshield Glass *b Ceramic Notch
*c Windshield Glass Edge Side - -


Standard Dimension:
Area Dimension
a 15.4 mm (0.61 in.)



Hide 56117A 3.INSTALL WINDOW GLASS ADHESIVE DAM

a.

Using a brush or sponge, coat the installation area of the window glass adhesive dam with glass primer.

NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



b.

Install 2 new window glass adhesive dams to the windshield glass as shown in the illustration.

B590308C01
1.552,0.688 1.688,0.5 true 1.406,2.25 1.51,2.063 true 5.604,0.677 5.479,0.521 true 5.781,2.219 5.656,2.063 true 1.302,2.26 1.51,2.438 0.208,0.177 10 true *b 1.719,0.406 1.927,0.583 0.208,0.177 10 true *b 5.24,0.396 5.448,0.573 0.208,0.177 10 true *b 5.729,2.25 5.938,2.427 0.208,0.177 10 true *b 2.292,0.375 2.573,0.635 0.281,0.26 10 false *a
*a Back Side of Windshield Glass *b Ceramic Notch



Hide 56118A 4.INSTALL NO. 2 WINDOW GLASS ADHESIVE DAM

a.

Using a brush or sponge, coat the installation area of the No. 2 window glass adhesive dam with glass primer.

NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



b.

Install a new No. 2 window glass adhesive dam to the windshield glass as shown in the illustration.

B590309C01
1.458,1.406 1.573,1.208 true 5.854,1.385 5.729,1.208 true 2.135,0.073 2.448,0.271 0.313,0.198 10 false *a 1.323,1.417 1.521,1.615 0.198,0.198 10 true *b 5.854,1.375 6.052,1.573 0.198,0.198 10 true *b
*a Back Side of Windshield Glass *b Ceramic Notch



Hide 75533G 5.INSTALL WINDSHIELD OUTSIDE MOULDING

a.

Using a brush or sponge, coat the installation area of the windshield outside moulding with glass primer.

NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



b.

Install a new windshield outside moulding to the windshield glass as shown in the illustration.

B590310C01
0.99,0.969 1.063,1.135 true 3.76,0.958 3.677,1.146 true 0.771,1.708 1.083,1.865 0.313,0.156 10 false *a 1.052,1.167 1.25,1.323 0.198,0.156 10 true *b 3.542,1.167 3.75,1.333 0.208,0.167 10 true *b 2.708,1.458 2.854,1.615 0.146,0.156 10 false A 2.688,1.885 2.833,2.042 0.146,0.156 10 true A 4.792,1.094 5.135,1.25 0.344,0.156 10 false A-A 6.063,1 6.208,1.156 0.146,0.156 10 false a
*a Back Side of Windshield Glass *b Ceramic Notch


Standard Dimension:
Area Dimension
a 1.65 to 3.15 mm (0.0650 to 0.124 in.)



Hide 56111 6.INSTALL WINDSHIELD GLASS

a.

Clean and shape the contact surface of the vehicle body.

i.
B590311C01
0,0 0,0 false
V100155

Adhesive


Using a knife, cut away excess adhesive on the contact surface of the vehicle body as shown in the illustration.

NOTICE:

Leave as much adhesive on the vehicle body as possible.



ii.

Clean the contact surface of the vehicle body with a piece of cloth saturated with non-residue solvent.



b.

Position the windshield glass.

i.

Using suction cups, place the windshield glass in the correct position.


ii.

Check that the whole contact surface of the windshield glass rim is perfectly even.


iii.
B590300C01
1.167,1.813 1.646,1.677 1.646,1.677 1.302,1.615 true 1.708,1.563 1.917,1.75 0.208,0.188 10 true *a
*a Matchmark


Align the matchmarks on the windshield glass and vehicle body.

NOTICE:

Check that the windshield glass stoppers are engaged to the vehicle body correctly.



iv.

Remove the windshield glass.



c.

Using a brush, coat the installation surface on the vehicle body with body primer.

NOTICE:
·

Do not coat the adhesive with body primer.

·

Do not apply too much body primer.

·

Allow the body primer to dry for 3 minutes or more.

·

Throw away any leftover body primer.



HINT:

If an area other than specified is coated by accident, wipe off the body primer with a clean piece of cloth before it dries.



d.

Using a brush or sponge, coat the adhesive application area with glass primer.

B590313C01
5.99,2.906 6.25,2.76 false 6.292,2.635 6.604,2.792 0.313,0.156 10 false *1 5.76,0.146 5.917,0.302 0.156,0.156 10 false a 0.5,1.604 0.813,1.76 0.313,0.156 10 false *a 4.719,0.25 5.042,0.417 0.323,0.167 10 false A-A 2.406,1.51 2.563,1.667 0.156,0.156 10 false B 2.417,1.885 2.542,2.042 0.125,0.156 10 true B 3.156,1.75 3.313,1.906 0.156,0.156 10 true A 3.115,1.438 3.271,1.594 0.156,0.156 10 false A 3.5,1.906 3.656,2.063 0.156,0.156 10 false C 3.156,1.979 3.313,2.135 0.156,0.156 10 true C 3.438,2.813 3.563,2.979 0.125,0.167 10 true D 3.521,3.146 3.677,3.302 0.156,0.156 10 false D 4.719,1.26 5.042,1.427 0.323,0.167 10 false B-B 5.063,2.396 5.385,2.563 0.323,0.167 10 false C-C 4.646,3.74 4.969,3.906 0.323,0.167 10 false D-D 5.771,1.156 5.927,1.313 0.156,0.156 10 false b 5.76,2.354 5.917,2.51 0.156,0.156 10 false c 5.708,3.677 5.865,3.833 0.156,0.156 10 false d
*1 Window Glass Adhesive Dam - -
*a Back Side of Windshield Glass - -
V100155

Glass Primer - -


Standard Dimension:
Area Dimension
a 8.25 mm (0.325 in.)
b 11 mm (0.433 in.) or more
c 10.4 mm (0.409 in.)
d 19 mm (0.748 in.) or more


NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:
·

Apply glass primer to the ceramic notches.

·

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.




e.

Apply adhesive to the windshield glass.

Adhesive:

Toyota Genuine Windshield Glass Adhesive (High modulus type) or equivalent


i.
B214800C28
1.198,0.438 1.385,0.5 false 0.5,0.625 0.656,0.823 0.156,0.198 10 false a 1.344,1.365 1.5,1.563 0.156,0.198 10 false a 1.115,0.885 1.271,1.083 0.156,0.198 10 false b 0.76,1 0.917,1.198 0.156,0.198 10 false b 1.406,0.438 1.646,0.615 0.24,0.177 10 false *a
*a Cartridge Nozzle
V100155

Adhesive


Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard Dimension:
Area Dimension
a 12 to 15 mm (0.472 to 0.591 in.)
b 8.0 to 11 mm (0.315 to 0.433 in.)




f.

Load the sealer gun with the cartridge.


g.

Apply adhesive to the windshield glass as shown in the illustration.

B590314C01
5.979,2.917 6.24,2.781 false 6.271,2.635 6.583,2.792 0.313,0.156 10 false *1 4.75,0.229 5.167,0.375 0.417,0.146 10 false A-A 0.583,1.552 0.896,1.708 0.313,0.156 10 false *a 3.51,1.938 3.667,2.094 0.156,0.156 10 false C 3.521,3.167 3.677,3.323 0.156,0.156 10 false D 3.417,2.833 3.521,2.99 0.104,0.156 10 true D 3.156,2 3.313,2.156 0.156,0.156 10 true C 3.135,1.771 3.271,1.938 0.135,0.167 10 true A 3.094,1.427 3.229,1.594 0.135,0.167 10 false A 2.375,1.875 2.51,2.042 0.135,0.167 10 true B 2.375,1.51 2.51,1.677 0.135,0.167 10 false B 5.896,0.188 6.052,0.365 0.156,0.177 10 false a 5.917,1.156 6.073,1.333 0.156,0.177 10 false b 5.74,2.365 5.896,2.542 0.156,0.177 10 false c 5.938,3.729 6.094,3.906 0.156,0.177 10 false d 4.865,1.188 5.281,1.333 0.417,0.146 10 false B-B 4.927,2.375 5.344,2.521 0.417,0.146 10 false C-C 4.719,3.719 5.135,3.865 0.417,0.146 10 false D-D
*1 Window Glass Adhesive Dam - -
*a Back Side of Windshield Glass - -
V100155

Adhesive - -


Standard Dimension:
Area Dimension
a 9.5 mm (0.374 in.)
b 9.5 mm (0.374 in.)
c 6.4 mm (0.252 in.)
d 4.0 mm (0.157 in.)



h.

Install the windshield glass.

i.
B590300C01
1.167,1.813 1.646,1.677 1.646,1.677 1.302,1.615 true 1.708,1.563 1.917,1.75 0.208,0.188 10 true *a
*a Matchmark


Using suction cups, position the windshield glass so that the matchmarks are aligned, and press it in gently along the rim.

NOTICE:
·

Check that the windshield glass stoppers are engaged to the vehicle body correctly.

·

Check the clearance between the vehicle body and windshield glass.




ii.

Lightly press the outer surface of the windshield glass to ensure that the windshield glass is securely fit to the vehicle body.

HINT:

Press the glass with a force of 98 N (10 kgf, 22.0 lbf) or more.



iii.

Using a scraper, remove any excess or protruding adhesive.


iv.

Hold the windshield glass using protective tape until the applied adhesive becomes hard.

HINT:

Follow the instructions supplied by the adhesive manufacturer or in the corresponding instruction manual for the minimum amount of time necessary to wait before driving the vehicle.




Hide 7.INSPECT FOR LEAK

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.


Hide 63311C 8.INSTALL ROOF HEADLINING

a.

Return the front section of the roof headlining to its original position.


Hide 74610A 10.INSTALL ASSIST GRIP SUB-ASSEMBLY

Hide 74348B 12.INSTALL VISOR HOLDER RH

HINT:

Use the same procedure as for the LH side.


Hide 74320 13.INSTALL VISOR ASSEMBLY LH

Hide 74310 14.INSTALL VISOR ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 81260A 15.INSTALL MAP LIGHT ASSEMBLY

Hide 62211 17.INSTALL FRONT PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 62312B 18.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

a.

Install the front door opening trim weatherstrip LH.


Hide 62311B 19.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 89941 21.INSTALL RAIN SENSOR (w/ Rain Sensor)

Hide 86401 22.INSTALL FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY (w/ Pre-collision System)

Hide 8646C 23.INSTALL FORWARD RECOGNITION CAMERA (w/ Pre-collision System)

Hide 24.INSTALL WINDSHIELD WIPER MOTOR AND LINK

Hide 8646C 25.ADJUST FORWARD RECOGNITION CAMERA

a.

If the forward recognition camera has been replaced with a new one or the windshield glass has been removed and installed, it is necessary to perform Forward Recognition Camera Learning.

HINT:

Forward Recognition Camera Learning can be performed by using either Target Adjustment (One Time Recognition) or Target Adjustment (Sequential Recognition) or Driving Adjustment.