Home › Engine / Hybrid System › G16E-GTS (ENGINE MECHANICAL) › ENGINE › from 2020.09
RM36W0E _51 Engine / Hybrid System _095252 G16E-GTS ENGINE MECHANICAL _0447807 ENGINE G

G16E-GTS ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

CAUTION:
·
A345137

When working near the engine room while the engine has started or the power source mode is engine switch on (IG), do not touch the fan and generator V belt or rotating components such as the fan, etc.

·

Touching the fan and generator V belt or rotating components such as the fan, etc. could result in your hand or clothing getting caught and pulled in.



PROCEDURE

Hide 17801 5.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Remove the air cleaner filter element sub-assembly.

Click hereGeneral>MAINTENANCE>G16E-GTS AIR CLEANER FILTER ELEMENT>REMOVAL


b.

Visually check that the air cleaner filter element sub-assembly is not damaged or excessively oily. If necessary, replace the air cleaner filter element sub-assembly.

HINT:
·

If there is any dirt or clogs in the air cleaner filter element sub-assembly, clean it with compressed air.

·

If any dirt or clogs remain even after cleaning the air cleaner filter element sub-assembly with compressed air, replace it.




c.

Install the air cleaner filter element sub-assembly.

Click hereGeneral>MAINTENANCE>G16E-GTS AIR CLEANER FILTER ELEMENT>INSTALLATION


Hide 16620D 7.INSPECT V-RIBBED BELT TENSIONER ASSEMBLY

a.

Remove the fan and generator V belt.

Click hereGeneral>MAINTENANCE>G16E-GTS DRIVE BELT>REMOVAL


b.

Turn the V-ribbed belt tensioner assembly clockwise and counterclockwise and check that it turns smoothly and does not catch.

HINT:

If the V-ribbed belt tensioner assembly does not turn smoothly or catches, replace the V-ribbed belt tensioner assembly.



c.

Install the fan and generator V belt.

Click hereGeneral>MAINTENANCE>G16E-GTS DRIVE BELT>INSTALLATION


Hide 13750 8.INSPECT VALVE LASH ADJUSTER ASSEMBLY NOISE

a.

Rev up the engine several times. Check that the engine does not emit unusual noises.


b.

If unusual noises occur, warm up the engine and idle it for 30 minutes or more, then perform the inspection.

HINT:

If any defects or problems are found during the inspection, perform the valve lash adjuster assembly inspection.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION



Hide 9.INSPECT IGNITION TIMING

NOTICE:
·

Check the ignition timing with the cooling fan off.

·

Turn off all electrical systems and the A/C.

·

When checking the ignition timing, the transaxle should be in neutral or park.



a.

Warm up and stop the engine.


b.

Connect the GTS to the DLC3.


c.

Start the engine and run it at idle.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Data List / Ignition Timing Cylinder #1.

Powertrain > Engine > Data List
Tester Display
Ignition Timing Cylinder #1
50003 372 213
Standard Ignition Timing:
Condition Specified Condition
Idle speed -5 to 15°CA BTDC



f.

Enter the following menus: Powertrain / Engine / Active Test / Activate the TC Terminal / ON.

Powertrain > Engine > Active Test
Active Test Display
Activate the TC Terminal
Data List Display
Ignition Timing Cylinder #1
50004 372 22 213

g.

Monitor Ignition Timing Cylinder #1 of the Data List.

Standard Ignition Timing:
Condition Specified Condition
Idle speed 8 to 12°CA BTDC



h.

Enter the following menus: Powertrain / Engine / Active Test / Activate the TC Terminal / OFF.


i.

Check that the ignition timing advances immediately when the engine speed is increased.


Hide 10.INSPECT ENGINE IDLE SPEED

NOTICE:
·

Check the ignition timing with the cooling fan off.

·

Turn off all electrical systems and the A/C.

·

When checking the ignition timing, the transaxle should be in neutral or park.



a.

Warm up and stop the engine.


b.

Connect the GTS to the DLC3.


c.

Start the engine and run it at idle.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed.

Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 372 211

f.

Read the value displayed on the tester.

Standard Idle Speed:
Condition Specified Condition
N Position 950 to 1050 rpm



Hide 11.INSPECT COMPRESSION

NOTICE:

Keep the spark plug holes free of foreign matter when measuring the compression pressure.


a.

Warm up and stop the engine.



c.

Remove the 3 spark plugs.

Click hereGeneral>MAINTENANCE>G16E-GTS SPARK PLUG>REMOVAL


d.

Disconnect the No. 5 engine wire connector.


e.

Disconnect the No. 6 engine wire connector.


f.

Check the cylinder compression pressure.

i.

Insert a compression gauge into the spark plug hole.


ii.

Fully open the throttle.


iii.

While cranking the engine, measure the compression pressure.

Standard Compression Pressure:
Item Minimum Compression Pressure Standard Compression Pressure
No.1 Cylinder 980 kPa
10.0 kgf/cm2
142 psi
1300 kPa
13.3 kgf/cm2
189 psi
No.2 Cylinder 980 kPa
10.0 kgf/cm2
142 psi
1300 kPa
13.3 kgf/cm2
189 psi
No.3 Cylinder 980 kPa
10.0 kgf/cm2
142 psi
1300 kPa
13.3 kgf/cm2
189 psi
Pressure Difference between Each Cylinder - 200 kPa or less
2.0 kgf/cm2 or less
29 psi or less


NOTICE:
·

Always use a fully charged auxiliary battery to obtain an engine speed of 250 rpm or more.

·

Inspect all cylinders in the same way.

·

Measure the compression pressure as quickly as possible.




iv.

If the cylinder compression pressure is low, pour a small amount of engine oil into the cylinder through the spark plug hole and inspect it again.

HINT:
·

If adding oil increases the compression pressure, the piston rings and/or cylinder bore may be worn or damaged.

·

If the compression pressure stays low, a valve may be stuck or seated improperly, or there may be leaks in the cylinder head gasket.





g.

Connect the No. 6 engine wire connector.


h.

Connect the No. 5 engine wire connector.


i.

Install the 3 spark plugs.

Click hereGeneral>MAINTENANCE>G16E-GTS SPARK PLUG>INSTALLATION


j.

Clear the DTCs.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

NOTICE:

After the inspection, clear the DTCs, check for DTCs again and make sure the normal system code is output.



Hide 12.INSPECT CO/HC

HINT:

This check determines whether or not the idle CO/HC complies with regulations.


a.

Start the engine.


b.

Run the engine at 2500 rpm for approximately 180 seconds.


c.

Insert a CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe during idle.


d.

Immediately check the CO/HC concentration during idle and when the engine is running at 2500 rpm.

HINT:

When performing a 2 mode (with the engine idling/running at 2500 rpm) test, the measurement procedures are determined by applicable local regulations.

If the CO/HC concentration does not comply with the regulations, perform troubleshooting in the order given below.



ii.

See the following table for possible causes, then inspect the applicable parts and repair them if necessary.

CO HC Problem Cause
Normal High Rough idle
1.

Faulty ignition:

-

Incorrect valve timing

-

Fouled, shorted or improperly gapped spark plugs


2.

Incorrect valve clearance (valve lash adjuster assembly)

3.

Leaks in intake or exhaust valves

4.

Leaks in cylinders


Low High Rough idle (Fluctuating HC reading)
1.

Vacuum leaks:

-

PCV hoses

-

Intake manifold

-

Throttle body with motor assembly


2.

Lean mixture causing misfire


High High Rough idle (Black smoke from exhaust)
1.

Restricted air cleaner filter element sub-assembly

2.

Plugged PCV valve

3.

Faulty SFI systems:

-

Fuel pressure regulator assembly

-

Engine coolant temperature sensor

-

Mass air flow meter

-

ECM

-

Fuel injector assemblies

-

Throttle position sensor (built into throttle body with motor assembly)