Home › Suspension › REAR SUSPENSION › REAR COIL SPRING (for TMC Made G16E-GTS) › from 2020.09
RM36W0E _53 Suspension _087264 REAR SUSPENSION _0447923 REAR COIL SPRING(for TMC Made G16E-GTS) A

REAR SUSPENSION  REAR COIL SPRING(for TMC Made G16E-GTS)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 48259A 1.INSTALL REAR UPPER COIL SPRING INSULATOR

a.

Install the rear upper coil spring insulator to the vehicle.


Hide 48258C 2.INSTALL REAR LOWER COIL SPRING INSULATOR

a.

Install the rear lower coil spring insulator to the rear No. 2 suspension arm assembly.


Hide 48231B 3.INSTALL REAR COIL SPRING

a.
C445831C01
1.458,3.635 1.885,3.635 true 1.448,3.719 1.646,3.719 1.646,3.719 1.646,3.646 true 1.917,3.531 2.229,3.688 0.313,0.156 10 false *a 0.229,0.771 0.542,0.927 0.313,0.156 10 false *b 0.146,1.406 0.458,1.563 0.313,0.156 10 false *b
*a Identification Mark
*b 30° or less
V100135

Inner Side of the Vehicle


Set the rear coil spring to the rear No. 2 suspension arm assembly.

NOTICE:
·

Set the rear coil spring so that its lower end is within the range shown in the illustration.

·

Set the rear coil spring so that the identification mark is positioned as shown in the illustration.




b.
C445828C02
0.865,1.583 1.219,1.458 true 2.021,1.813 2.427,1.813 false 0.656,1.5 0.885,1.719 0.229,0.219 10 false *a 2.458,1.708 2.771,1.865 0.313,0.156 10 false *b
*a Wooden Block
*b Jack


Using a jack and wooden block, slowly jack up the rear No. 2 suspension arm assembly and then install the rear No. 2 suspension arm assembly to the rear axle carrier sub-assembly with the bolt and nut.

CAUTION:
C349515

·

Do not raise the jack up too high.

·

The vehicle could fall, resulting in a serious accident.



NOTICE:
·

Tighten the bolt with the nut secured.

·

When jacking up the rear No. 2 suspension arm assembly, be sure to jack it up slowly.

·

Make sure to perform this operation with the vehicle kept as low as possible.

·

Insert the bolt with the threaded end facing the front of the vehicle.




Hide 48740F 5.FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY

a.
C445829

Install the rear No. 2 suspension arm assembly (rear axle carrier sub-assembly side) with the bolt.

Torque:
73 N*m (744 kgf*cm, 54 ft.*lbf)

NOTICE:

Tighten the bolt with the nut secured.



Hide 48840A 6.INSTALL REAR STABILIZER LINK ASSEMBLY

Hide 7.INSTALL REAR WHEEL

Hide 48740F 8.FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY

a.

Install the rear No. 2 suspension arm assembly (rear suspension member sub-assembly side) with the nut.

Click hereSuspension>REAR SUSPENSION>REAR LOWER ARM>INSTALLATION