Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY (for G16E-GTS) › from 2020.09
RM36W0E _52 Drivetrain _087547 DRIVE SHAFT / PROPELLER SHAFT _0447996 FRONT DRIVE SHAFT ASSEMBLY(for G16E-GTS) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for G16E-GTS)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 43420G 1.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH

a.

Install a new front drive shaft hole snap ring LH to the front drive shaft assembly LH.


Hide 43457B 2.INSTALL DRIVE SHAFT BEARING BRACKET HOLE SNAP RING

a.

Install a new drive shaft bearing bracket hole snap ring to the front drive shaft assembly RH.


Hide 43420 3.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH

a.

Coat the snap ring of the front drive inboard joint assembly with MP grease.


b.

Coat the splines of the front drive inboard joint assembly with Toyota genuine manual transmission gear oil LV.


c.
C406945C01
0.406,0.271 0.719,0.469 0.313,0.198 10 false *a
*a Cross Section of Front Drive Shaft Oil Seal LH
V100145

MP Grease
V100144

Toyota Genuine Oil Seal Side Lip Grease


Coat the lip of the front drive shaft oil seal LH with MP grease and Toyota genuine oil seal side lip grease as shown in the illustration.

HINT:

Apply a light coat of MP grease and Toyota genuine oil seal side lip grease to the entire circumference of the front drive shaft oil seal LH.



d.
C445305

Align the inboard joint splines, and using a brass bar and a hammer, install the front drive shaft assembly LH.

NOTICE:
·

Face the end gap of the front drive shaft hole snap ring downward.

·

Do not damage the front drive shaft oil seal LH.

·

Do not damage the front axle inboard joint boot LH.

·

Make sure to center the front drive shaft assembly LH during installation to prevent damage to the front drive shaft hole snap ring.



HINT:

Confirm whether the drive shaft is securely driven in by checking the reaction force and sound.



Hide 43410 4.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

a.

Coat the splines of the front drive inboard joint assembly with Toyota genuine manual transmission gear oil LV.


b.

Coat the lip of the transfer case oil seal RH with MP grease.

HINT:

Apply a light coat of MP grease to the entire circumference of the transfer case oil seal RH.



c.

Align the inboard joint splines and install the front drive shaft assembly RH.

NOTICE:
·

Do not damage the transfer case oil seal RH.

·

Do not damage the front drive shaft oil seal RH.




d.

Install the drive shaft bearing bracket hole snap ring to the drive shaft bearing bracket.


e.

Install a new bolt.

Torque:
32.4 N*m (330 kgf*cm, 24 ft.*lbf)


Hide 43420 5.INSTALL FRONT DRIVE SHAFT ASSEMBLY

a.
C445306C01
0,0 0,0 false
V100135

Toyota Body Grease W


Apply 0.1 to 0.3 g (0.00353 to 0.0105 oz) of Toyota body grease W to each of the 4 areas shown in the illustration.


b.
C445300C01
2.677,0.479 2.854,0.542 2.854,0.542 2.75,0.719 true 2.875,0.448 3.063,0.646 0.188,0.198 10 true *a
*a Matchmark


Align the matchmarks and install the front drive shaft assembly to the front axle assembly.

NOTICE:
·

Check that there is no foreign matter on the deflector or contact surfaces.

·

Do not push the front axle hub sub-assembly towards the outside of the vehicle any further than necessary.

·

Do not damage the front axle outboard joint boot.

·

Do not deform the front disc brake dust cover.

·

Do not damage the deflector.




Hide 48069 6.INSTALL FRONT LOWER NO.1 SUSPENSION ARM SUB-ASSEMBLY

Hide 48810 7.INSTALL FRONT STABILIZER LINK ASSEMBLY

Hide 45047 8.INSTALL TIE ROD END SUB-ASSEMBLY

Hide 43502H 10.INSTALL FRONT AXLE SHAFT NUT

a.

Clean the threaded parts on the front drive shaft assembly and a new front axle shaft nut using non-residue solvent.

NOTICE:
·

Be sure to perform this work even when using a new front drive shaft assembly.

·

Keep the threaded parts free of oil and foreign matter.




b.

Using a 30 mm deep socket wrench, install the front axle shaft nut while applying the brakes.

Torque:
294 N*m (2998 kgf*cm, 217 ft.*lbf)


c.
C445307

Using a chisel and a hammer, stake the front axle shaft nut.


Hide 11.ADD MANUAL TRANSAXLE OIL

Hide 13.INSPECT FOR MANUAL TRANSAXLE OIL LEAK

Hide 14.INSPECT FOR TRANSFER OIL LEAK

Hide 51441C 16.INSTALL ENGINE UNDER COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 51410 17.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 18.INSTALL FRONT WHEEL

Hide 19.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT