Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › REAR DRIVE SHAFT ASSEMBLY › from 2020.09
RM36W0E _52 Drivetrain _087547 DRIVE SHAFT / PROPELLER SHAFT _0447998 REAR DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  REAR DRIVE SHAFT ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the rear drive shaft assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Rear wheel alignment adjustment Calibration
·

DTCs are stored

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.DRAIN DIFFERENTIAL OIL

Hide 2.REMOVE REAR WHEEL

Hide 42312B 3.REMOVE REAR AXLE SHAFT NUT

a.
C445880N01
2.625,1.365 2.813,1.188 false 2.844,1.094 3.302,1.292 0.458,0.198 10 false SST

Using SST and a hammer, release the staked part of the rear axle shaft nut.

SST
09930-00010  

NOTICE:

Loosen the staked part of the rear axle shaft nut completely, otherwise the threads of the rear drive shaft assembly may be damaged.



b.

Using a 30 mm deep socket wrench, remove the rear axle shaft nut while applying the brakes.


Hide 47319F 5.SEPARATE REAR FLEXIBLE HOSE

a.
C448009

Remove the bolt and separate the rear flexible hose from the flexible hose bracket.


Hide 48840A 6.REMOVE REAR STABILIZER LINK ASSEMBLY

Hide 48258C 8.REMOVE REAR LOWER COIL SPRING INSULATOR

Hide 48740F 9.REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY

Hide 48720A 10.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY

Hide 48790 11.SEPARATE REAR UPPER CONTROL ARM ASSEMBLY

a.
C448010

Remove the bolt and nut, and separate the rear upper control arm assembly from the rear axle carrier sub-assembly.

NOTICE:

Loosen the bolt with the nut secured.



Hide 42340B 12.REMOVE REAR DRIVE SHAFT ASSEMBLY

a.
C448011C01
2.885,1.385 3.031,1.219 3.031,1.219 2.813,1.083 true 3.052,1.135 3.25,1.344 0.198,0.208 10 true *a
*a Matchmark


Put matchmarks on the rear drive shaft assembly and the rear axle hub and bearing assembly.


b.
C448012

Using a plastic hammer, separate the rear drive shaft assembly from the rear axle hub and bearing assembly.

NOTICE:
·

Do not push the rear axle hub and bearing assembly towards the outside of the vehicle any further than necessary.

·

Do not damage the rear drive shaft outboard joint boot.

·

Do not deform the parking brake plate sub-assembly.

·

Do not damage the deflector.



HINT:

If it is difficult to separate the rear drive shaft assembly rear axle hub and bearing assembly, tap the end of the rear drive shaft assembly using a brass bar and a hammer.



c.
C448013N01
0.948,0.698 0.667,1.938 0.667,1.938 1.365,1.615 true 0.365,1.865 0.823,2.063 0.458,0.198 10 false SST

Using SST, remove the rear drive shaft assembly from the rear differential carrier assembly.

SST
09520-01010  
09520-20010  (09521-02010, 09521-02040, 09521-02060)

NOTICE:
·

Do not damage the rear drive shaft oil seal.

·

Do not damage the rear drive shaft inboard joint boot.

·

Do not drop the rear drive shaft assembly.

·

When removing the rear drive shaft assembly, keep it level.




Hide 42360M 13.REMOVE REAR DRIVE SHAFT INBOARD JOINT SHAFT SNAP RING

C129495

a.

Using a screwdriver, remove the rear drive shaft inboard joint shaft snap ring.